• 한국표면공학회지
• /
• 제45권3호
• /
• pp.130-135
• /
• 2012

Hydrogen charging was electrochemically conducted at high strength DP steels and TRIP steel with varying charging time. The penetration depths and the mechanical properties with charging conditions were investigated through the distribution of micro-hardness and the microstructural observation of the subsurface zone. The micro-Vickers hardness was measured to evaluate the hydrogen embrittlement of subsurface zone in addition to the microscope investigation. It was shown that the hydrogen amounts decreased in DP steels and TRIP steel with increasing hydrogen charging time. As shown by micro-Vickers hardness test and small punch test results, micro-Vickers hardness and SP energy for DP steels and TRIP steel decreased with increasing hydrogen charging time, for constant value of charging current density. SEM investigation results for the hydrogen contained samples showed that the major fracture behavior was brittle fracture which results in dimples on fractured surface and the size of dimples were decreased with increasing hydrogen charging time. These results indicate that hydrogen embrittlement is the major cause for the fracture of high strength steels and also micro-Vickers hardness test and small punch test is a valuable test method for hydrogen embrittlement of high strength sheet steels.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1355-1360
• /
• 2007

The use of high strength steels are gradually increasing to reduce the weight of automobile to improve the environmental problems and collision safety. To encounter the traditional disadvantages of high strength steels like as a poor formability and high springback, hot press forming has been developed. By this method, the strength of steel sheet is increased about three times of original one through die quenching process. In order to the design of hot press forming tools by using numerical simulation, the knowledge of mechanical and microstructural characteristics are required. This study show the mechanical and microstructural characteristics of a high strength boron-alloyed steel according to the various quenching conditions.

• 한국재료학회지
• /
• 제29권3호
• /
• pp.189-195
• /
• 2019

The effect of C, Mn, and Al additions on the tensile and Charpy impact properties of austenitic high-manganese steels for cryogenic applications is investigated in terms of the deformation mechanism dependent on stacking fault energy and austenite stability. The addition of the alloying elements usually increases the stacking fault energy, which is calculated using a modified thermodynamic model. Although the yield strength of austenitic high-manganese steels is increased by the addition of the alloying elements, the tensile strength is significantly affected by the deformation mechanism associated with stacking fault energy because of grain size refinement caused by deformation twinning and mobile dislocations generated during deformation-induced martensite transformation. None of the austenitic high-manganese steels exhibit clear ductile-brittle transition behavior, but their absorbed energy gradually decreases with lowering test temperature, regardless of the alloying elements. However, the combined addition of Mn and Al to the austenitic high-manganese steels suppresses the decrease in absorbed energy with a decreasing temperature by enhancing austenite stability.

• Metals and materials international
• /
• 제24권6호
• /
• pp.1202-1212
• /
• 2018

The effects of Nickle (Ni) addition on bainitic transformation and property of ultrahigh strength bainitic steels are investigated by three austempering processes. The results indicate that Ni addition hinders the isothermal bainite transformation kinetics, and decreases the volume fraction of bainite due to the decrease of chemical driving force for nucleation and growth of bainite transformation. Moreover, the product of tensile strength and total elongation (PSE) of high carbon bainitic steels decreases with Ni addition at higher austempering temperatures (220 and $250^{\circ}C$), while it shows no significant difference at lower austempering temperature ($200^{\circ}C$). For the same steel (Ni-free or Ni-added steel), the amounts of bainite and RA firstly increase and then decrease with the increase of the austempering temperature, resulting in the highest PSE in the sample austempered at temperature of $220^{\circ}C$. In addition, the effects of austempering time on bainite amount and property of high carbon bainitic steels are also analyzed. It indicates that in a given transformation time range of 30 h, more volume of bainite and better mechanical property in high carbon bainitic steels can be obtained by increasing the isothermal transformation time.

• 한국강구조학회 논문집
• /
• 제17권4호통권77호
• /
• pp.395-405
• /
• 2005

본 논문은 고항복비-고강도강의 효율적인 이용을 위하여 유강혼합구조 시스템의 실험결과를 요약한 것이다. 최근 건축구조물에서도 대형화 및 초고층화 되어감에 따라 사용강재에 대하여 높은 성능을 요구하게 되었고, 고강도강을 사용해야 하는 경우가 늘고 있다. 하지만 고강도강은 항복비가 높고 최대 응력시 변형도가 작고 탄성계수가 연강과 같다는 단점으로 인하여 수요가 증가하고 있지 못한 실정이다. 이러한 고항복비를 가지는 고강도강의 결점을 보완하고 효과적인 사용을 위해서는 새로운 구조시스템이 필요하다. 본 연구에서는 고항복비를 가지는 고강도강을 건축구조물에 효과적으로 적용할 수 있는 방안으로 유강혼합구조 시스템을 제안하고, 고강도강이 포함된 유강혼합기둥 실험을 통하여, 고강도강을 효율적으로 사용할 수 있는 가능성을 제시하고자 하였다. 내력비와 강성비를 포함할 수 있는 강요소 (stiff element)와 유요소 (flexible element)의 항복변형비를 변수로 하여, 유강혼합구조시스템 적용시 적절한 항복변형비를 찾고자 하였다. 실험결과 제안된 유강혼합구조시스템은 연강만으로 이루어진 시스템에 비해 높은 에너지 흡수능력을 보여주었고, 강요소에 대한 유요소의 항복변형비가 2.7~3.3일 때 가장 큰 에너지 흡수능력을 갖는 것을 확인할 수 있었다.

• 대한금속재료학회지
• /
• 제48권9호
• /
• pp.798-806
• /
• 2010

The effects of alloying elements and the cooling condition on the microstructure, tensile properties, and Charpy impact properties of high-strength bainitic steel plates fabricated by a controlled rolling process were investigated in the present study. Eight kinds of steel plates were fabricated by varying C, Cr, and Nb additions under two different cooling rates, and their microstructures and tensile and Charpy impact properties were evaluated. The microstructures present in the steels increased in the order of granular bainite, acicular ferrite, bainitic ferrite, and martensite as the carbon equivalent or cooling rate increased, which resulted in a decrease in the ductility and Charpy absorbed energy. The steels containing a considerable amount of bainitic ferrite or martensite showed very high strengths, together with good ductility and Charpy absorbed energy. In order to achieve the best combination of strength, ductility, and Charpy absorbed energy, granular bainite and acicular ferrite were properly included in the high-strength bainitic steels by controlling the carbon equivalent and cooling rate, while about 50 vol.% of bainitic ferrite or martensite was maintained to maintain the high strength.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.269-273
• /
• 2003

There is a growing interest to replace the commercial steels with non-heat treated steels, which does not involve the spheroidization and quenching-tempering treatment. However, Non-heat treated steels should satisfy high strength and good formability without performing heat treatment. Therefore, it is important to investigate optimum materials showing a good combination of strength and formability after the drawing process. In this study, Dual-Phase Steels were studied as candidate materials for non-heat treated steels, which have different martensite morphologies and volume fractions obtained through heat-treatment of intercritical quenching (IcQ), intermediate quenching (ImQ) and step quenching (SQ). The mechanical properties of DP steels were measured by tension and compression tests. Also, the cold formability of three DP steels which have similar tensile strength value was investigated by estimating the deformation resistance and the forming limit. The deformation resistance which is important factor in determining die life was estimated by calculating the deformation energy. And the forming limit was estimated by measuring the critical strain revealing crack initiation at the notch tip of the specimens.

• 소성∙가공
• /
• 제13권1호
• /
• pp.84-89
• /
• 2004

There is a growing interest to replace the commercial steels with non-heat treated steels, which does not involve the spheroidization and quenching-tempering treatment. However, Non-heat treated steels should satisfy high strength and good formability without performing heat treatment. Therefore, it is important to investigate optimum materials showing a good combination of strength and formability after the drawing process. In this study, Dual-Phase Steels were studied as candidate materials for non-heat treated steels, which have different martensite morphologies and volume fractions obtained through heat-treatment of intercritical quenching (IcQ), intermediate quenching (ImQ) and step quenching (SQ). The mechanical properties of DP steels were measured by tension and compression tests. Also, the cold formability of three DP steels which have similar tensile strength value was investigated by estimating the deformation resistance and the forming limit. The deformation resistance which is important factor in determining die life was estimated by calculating the deformation energy. And the forming limit was estimated by measuring the critical strain revealing crack initiation at the notch tip of the specimens.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.385-386
• /
• 2006

For attaining optimum fatigue resistance of PM steels, high density levels are necessary. In this work, sintered steels Fe-1.5%Mo-0.6%C and Fe-1.5%Cr-0.2%Mo-0.6%C were produced with density levels of 7.1 to $7.6\;g.cm^{-3}$. Ultrasonic fatigue testing with 20 kHz was performed in push-pull mode up to 10E9 cycles. It was shown that the fatigue endurance strength is strongly improved by higher density levels, but also higher sintering temperatures are beneficial. The Cr-Mo steels proved to be superior to the plain Mo alloyed, due to a more favourable as-sintered matrix microstructure.

• 한국표면공학회지
• /
• 제8권1호
• /
• pp.15-23
• /
• 1975

Electrodeposition of metals form aqueous solutions (eg, electroplating ) is frequently accompanied, by the discharge of hydrogen ions(in acidic solutions) or water molecules ( in alkaline electrolytes). The atomic hydrogen produced thus may partly diffuse into the interior of the substrate and when this is absorbed by iron/steel substrate, it has detrimental effects on the mechanical properties of the steel, leading to ahydrogen embrittlement. Steels, particularly the high strength steels, are prone to hydrogen embrittlement. In view of the increasing applications of high strength steels in variousindustries, particularly in the aircraft manufacture, there has been renewed interest in the studiesonhydrogen embrittlement during electroplating of metals. In this review, the author summarizes the reports on hydrogen embrittlement during preplating of metals. In this review , the author sumamrizes the hydrogen embrittlement during electroplating of metals. In this review , the author summarizes the reports on hydrogen embrittlement during preplating operations and electroplating of metals like copper, nickel, tin, zinc ,cadimum and chromium. Finally, the effect of degassing by baking to deembrittle the plated high tensile steels and mechanism of hydrogen embrittlement are briefly indicated.