• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.331-334
• /
• 2009

This paper presents the characteristics of external inductor for impulse current waveform with 10/350 ${\mu}s$ time parameters. Impulse generator was composed with capacitor having large capacitance and low working voltage for the safe of operator and small discharging sound. Parallel R-L-C circuits with crow-bar gaps and superposition method were proposed to make a high current lightning impulse according to IEC 62305-1. The high energy inductor with several taps for fitting half decay time T2 within the tolerance range and experimental data of inductance according to charging voltages were suggested.

• Journal of Power Electronics
• /
• v.14 no.3
• /
• pp.432-443
• /
• 2014

In order to improve the output efficiency of solar cells and to extend the life span of batteries, the input currents of converters are required to be continuous. If low output voltage ripple is required at the same time, it is obvious that the application of basic two-order converters (such as Buck and Boost derived converters) will not be good enough. In this paper, a lot of non-isolated push-pull converters (NIPPCs) with continuous current will be introduced due to their lower current stress, higher efficiency and better EMC performance. By decomposing the converters into push-pull cells, inductor and free-wheeling diodes, two families of NIPPCs based on single inductor and coupled inductor separately are systematically generated. Furthermore, characteristics analyses for some of the generated converters are also shown in this paper. Finally, two prototypes based on the corresponding typical topologies are built in the lab to verify the theoretical outcomes.

• Journal of Power Electronics
• /
• v.2 no.3
• /
• pp.199-205
• /
• 2002

This paper compares three kinds of soft-switching circuits from viewpoints of surge suppression, load characteristic, and power efficiency for a tapped-inductor buck converter with low voltage and high current. As a result, these soft-switching techniques have achieved much higher efficiency of 80 % when compared with a hard-switching buck converter for the output condition of 1V and 20A.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2004.05a
• /
• pp.154-158
• /
• 2004

Power inductor is usually used in the field of the power circuit of a cellular phone, TFT LCD module etc.. This paper presents the development process of Power Inductor Full Automation Winding/Welding System for TFT LCD. This process, the process algorithm, high precision welding current control, design of welding head, high speed, high precision feeding mechanism, and user interface process control program technologies are included.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.3
• /
• pp.191-199
• /
• 2016

Conventional two-level Zeta converters have drawbacks, such as high voltage stresses and high current ripples. To address these problems, a three-level Zeta converter that uses a couple inductor is proposed in this study. The proposed converter utilizes the three-level power switching circuit to reduce the voltage stresses and inductor current ripples. Compared with the conventional converter, the proposed converter can improve power efficiency and power density. A 500 W prototype circuit is used to verify the operation and performance of the proposed converter via experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.494-495
• /
• 2007

As a pocket size electronic device have developed and electronic parts is increased, it need dual face soldering using SMT(Surface Mount Technology) and it can be getting high density soldering. Inductor is one of their electronic parts using SMT and inductor was developed to make electromagnetic energy. In this study, it is analyzed temperature properties of surface mount type Inductor due to current injection which is satisfied the demand of utmost small size and the substance of high density simultaneously.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.662-671
• /
• 2018

This paper presents a new structure for a step up dc-dc converter, which has several advantageous features. Firstly, the input dc source and the clamped capacitor are connected in series to transfer energy to the load through dual voltage multiplier cells. Therefore, the proposed converter can produce a very high voltage and a high conversion efficiency. Secondly, a double voltage clamped circuit is introduced to the primary side of the coupled inductor. The energy of the leakage inductance of the coupled inductor is recycled and the inrush current problem of the clamped circuits can be shared equally by two synchronous clamped capacitors. Therefore, the voltage spike of the switch tube is solved and the current stress of the diode is reduced. Thirdly, dual voltage multiplier cells can absorb the leakage inductance energy of the secondary side of the coupled inductor to obtain a higher efficiency. Fourthly, the active switch turns on at almost zero current and the reverse-recovery problem of the diodes is alleviated due to the leakage inductance, which further improves the conversion efficiency. The operating principles and a steady-state analysis of the continuous, discontinuous and boundary conduction modes are discussed in detail. Finally, the validity of this topology is confirmed by experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.1
• /
• pp.53-58
• /
• 2021

Operation of the interleaved Boost PFC converter in Critical Conduction Mode (CrM) shows the advantages of high efficiency and good EMI characteristics owing to the valley switching of FET. However, when it is designed for a highly pulsating load, operation at a relatively high frequency is inevitable at non-pulsating typical load condition, resulting in efficiency degradation. Moreover, the physical size of the inductor becomes problematic because of the nature of the CrM operation, where the inductor peak current is about two times the inductor average current, thereby requiring high DC-bias characteristics, which is worse when the output power is high. In this study, a new parallel driving method of two sets of interleaved boost PFC converters for highly pulsating high-power application is proposed. The proposed method does not require any additional load-sharing controller, resulting in high efficiency and smaller inductor size.

• Journal of Magnetics
• /
• v.20 no.2
• /
• pp.138-147
• /
• 2015

The unique nano-scale inter-lamellar microstructure and unparalleled heat treatment process give our developed metal powder composite its outstanding magnetic property for power inductor & motor applications. Compared to the conventional polycrystalline Fe or amorphous Fe-Cr-Si-B alloys, our unique designed inter-lamellar microstructure strongly decreases the intra-particle eddy current loss at high frequencies by blocking the mutual eddy currents. The combination of optimum permeability, magnetic flux and extremely low core loss makes this powder composite suitable for high frequency applications well above 10 MHz. Moreover, it can be also possible to SMC core for high speed motor applications in order to increase the motor efficiency by decreasing the core loss.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1187-1189
• /
• 2002

In the case of an existing high frequency inverter is became forced extinction by quick load change, due to be connected with series inductor on switch, it is destroyed or is generated conduction loss by resistance component in reactor. And, In the operation of high current with a soft switching, conduction loss can not neglect. In this paper, for the high current power source, we make sure of soft swtching operation and reducing surge when the forced extinction by using a connected switch with series inductor. Also, we poropos a topology of the half bridge type high frequency inverter that can be realized high amplitude operation of the load current. And, analyze the circuit to decide an opmtial circuit parameter.