• 대한전기학회논문지:전력기술부문A
• /
• 제49권6호
• /
• pp.280-288
• /
• 2000

Recently, there has been growing interest in utilizing cogeneration(COGN) systems with a high-energy efficiency due to the increasing energy consumption and the lacking of energy resource. But an insertion of COGN system to existing power distribution system can cause several problems such as voltage variations, harmonics, protective coordination, increasing fault current etc, because of reverse power of COGN, especially in protective coordination. A study on a proper coordination with existing one is being required. The existing power distribution system is operated with radial type by one source and protection system is composed based on unidirectional power source. But an Insertion of COGN system to power distribution system change existing unidirectional power source system to bidirectional power source. Therefore, investigation to cover whole field of power distribution system must be accomplished such as changing of protection devices rating by increasing fault current, reevaluation of protective coordination. In this paper, simulation using PSCAD/EMTDC was accomplished to analyze effect of COGIN on distribution fault current. Also, the existing protection system of 22.9[kV] power distribution system and customers protection system to protect of COGIN was analyzed and the study on protective coordination between of two protection system accomplished.

• Journal of Power Electronics
• /
• 제19권1호
• /
• pp.220-233
• /
• 2019

This work aims to study and analyze the various operating modes of universal power converter which is powered by solar and thermoelectric generators. The proposed converter is operated in a DC-DC (buck or boost mode) and DC-AC (single phase) inverter with high efficiency. DC power sources, such as solar photovoltaic (SPV) panels, thermoelectric generators (TEGs), and Li-ion battery, are selected as input to the proposed converter according to the nominal output voltage available/generated by these sources. The mode of selection and output power regulation are achieved via control of the metal-oxide semiconductor field-effect transistor (MOSFET) switches in the converter through the modified stepped perturb and observe (MSPO) algorithm. The MSPO duty cycle control algorithm effectively converts the unregulated DC power from the SPV/TEG into regulated DC for storing energy in a Li-ion battery or directly driving a DC load. In this work, the proposed power sources and converter are mathematically modelled using the Scilab-Xcos Simulink tool. The hardware prototype is designed for 200 W rating with a dsPIC30F4011 digital controller. The various output parameters, such as voltage ripple, current ripple, switching losses, and converter efficiency, are analyzed, and the proposed converter with a control circuit operates the converter closely at 97% efficiency.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 추계학술발표회논문집(1)
• /
• pp.528-533
• /
• 1997

A CANFLEX(CANdu FLEXible fuelling) 43-element bundle has developed for a CANDU-6 reactor as an alternative of 37-element fuel bundle. The design has two diameter elements (11.5 and 13.5㎜) to reduce maximum element power rating and buttons to enhance the critical heat flux(CHF), compared with the standard 37-element bundle. The freon CHF experiments have performed for two series of CANFLEX bundles with and without buttons with a modelling fluid as refrigerant H-l34a and axial uniform heat flux condition. Evaluating the effects of buttons of CANFLEX bundle on CHF and Critical Channel Power(CCP) with the experimental results, it is shown that the buttons enhance CCP as well as CHF. All the CHF's for both the CANFLEX bundles are occurred at the end of fuel channel with the high dryout quality conditions. The CHF enhancement ratio are increased with increase of dryout quality for all flow conditions and also with increase of mass flux only lot high pressure conditions. It indicates that the button is a useful design lot CANDU operating condition because most CHF flow conditions for CANDU fuel bundle are ranged to high dryout quality conditions.

• 전력전자학회논문지
• /
• 제12권3호
• /
• pp.234-240
• /
• 2007

본 논문에서는 비대칭 컨버터에 비하여 전력소자의 수를 감소하면서도, 고속 운전에 적합한 새로운 멀티레벨 인버터를 제안한다. 제안된 인버터는 기존의 비대칭 컨버터에 비하여 전력소자의 수를 감소시킬 수 있는 특징이 있으며, SRM의 감자구간에서 휠링되는 에너지와 전원에서 공급되는 에너지를 교차적으로 활용하는 방식을 적용함으로써, C-dump 인버터에 비해 커패시터의 정격전압을 낮출 수 있는 장점이 있다. 또한, 제안된 멀티레벨 인버터의 동작 모드는 비대칭 컨버터에 비하여, 충전 레벨의 전원을 정역으로 활용하여 빠른 여자(Excitation)와 감자(Demagnetization) 모드를 가지게 되므로, 제어의 활용성이 매우 높다. 따라서, SRM의 고속 운전에 필요한 여자전류의 빠른 확립을 통하여 응답시간을 개선시키며, 토크 발생구간을 확장시킬 수 있다. 제안된 멀티레벨 인버터 구동형 SRM의 운전특성은 시뮬레이션과 실험을 통해 검증하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 F
• /
• pp.2234-2236
• /
• 1997

The SIT, a Static Induction Transistor, is a semiconductor switch that is also called the power junction field-effect transistor (power JFET). Its characteristics are similar to a MOSFET except that its power level is higher and its maximum frequency of operation is lower. The normal method to protect against internal circuit transients of the form of di/dt or dv/dt is the use of snubber circuits. However, the limits of di/dt and dv/dt are high enough for the SIT that it is possible to operate without snubber circuits. SITs can be connected in parallel in order to cope with higher load currents that the value of an individual device rating. The purpose of this study is to investigate the parallel operation of SITs. In this experiment, we used a half-bridge inverter, the output of inverter is up to almost 1MHz and 2kW. Experimental results show that the operation of parallel connected SITs are facilitated individually good current sharing. The reason is the positive temperature coefficient of resistance of the SIT.

• 전력전자학회논문지
• /
• 제17권6호
• /
• pp.507-515
• /
• 2012

DC-DC converter which composed of LLC resonant converter, operated by fixed switching frequency with fixed duty cycle (50%), and flyback converter to provide constant output voltage($400V_{DC}$) with variation of input voltage($30-60V_{DC}$) is proposed in this paper. To obtain constant output voltage($400V_{DC}$), flyback converter is not operated in case of above the maximum input voltage($60V_{DC}$) and operated as the input voltage decreases to below 60VDC. Therefore, flyback converter can be designed to the 50% power rating of the maximum power in the proposed DC-DC converter. Operation modes and voltage gain characteristics were analyzed and a 360W prototype converter was tested to verify the proposed converter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.40-42
• /
• 1999

High-speed brushless permanent magnet machines are good for compressor and aerospace applications, etc, since they are conductive to high efficiency, high power density, small size and low weight. This paper describes a diametrically magnetized PM motor with the rating of 4.3kW and 50000 rpm fur high-speed drive applications. To bear strong stress from high speed, rotor was designed cylindrical structure, was magnetized diametrically permanent magnet. The performance characteristic of motor was evaluated by means of FEA(Finite Element Analysis), no-load test And then, in order to find back-EMF constant, used FEA, search coil.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.23-25
• /
• 2005

This paper describes analysis of transformer sheet winding losses and temperature rise. Sheet windings are used if transformer rating currents are so high that one meets current density limit on windings. Unlike stranded windings, sheet windings may be locally healed due to R direction flux. Winding losses with eddy current effect are calculated by finite element electromagnetic analysis and temperature rise is also calculated by Computational Fluid Dynamics (CFD) with loss result.

• Journal of Power Electronics
• /
• 제19권4호
• /
• pp.944-955
• /
• 2019

In this paper, the three-level T-type neutral-point-clamped indirect matrix converter topology and the relative space vector modulation methods are introduced to improve the voltage transfer ratio and output voltage performance. The presented converter topology is based on combinations of cascaded-rectifier and three-level T-type neutral-point-clamp inverter. It can overcome the limitation of voltage transfer ratio of the conventional matrix converter and the high voltage rating of power switches of conventional matrix converter. Two SVPWM strategies for proposed converter are described in this paper to achieve the advantages features such as: sinusoidal input/output currents and three-level output voltage waveforms. Results from Psim 9.0 software simulation are provided to confirm the theoretical analysis. Hence, a laboratory prototype was implemented, and the experimental results are shown to validate the simulation results and to verify the effectiveness of the proposed topology and modulation strategies.

• KEPCO Journal on Electric Power and Energy
• /
• 제2권3호
• /
• pp.403-407
• /
• 2016

In general, drum-type boilers are designed for base load duty and applied under constant pressure operation mode. Recently, however conditions often occur that even drum-type boilers have to operate at partial load conditions. A feasibility study on adopting the sliding pressure operation for drum-type boiler was conducted, and corresponding performance changes and effects on the equipment were analyzed by utilizing a process simulation model. As a result, the conclusion was reached that drum type boilers are able to adopt the sliding pressure operation and can improve of net efficiency at part load operation in spite of the Rankine cycle efficiency reduction due to the decreases in main steam pressure. Because of thank to improvement of high pressure turbine stage-1 internal efficiency and power savings of boiler feed water pump. The sliding pressure operation is advantageous in terms of stress level relief for boiler tube as well as maintaining the rating steam temperature at part load condition. However, cautions are required because the drum boilers have poor dynamic response characteristics which may get worse during the sliding pressure operation.