• 한국태양에너지학회 논문집
• /
• 제31권6호
• /
• pp.1-7
• /
• 2011

Sound waves and acoustic energy generated by two identical TA (ThermoAcoustic) lasers were analyzed and studied. One end of the ceramic stack was heated by a thin NiCr wire wound around that end. The other end of the stack was cooled by natural convection of atmospheric air. The wavelength of the sound waves generated by a single TA laser was four times the tube length and the amplitude of the waves increased with the heating rate. SPL (SoundPressure Level) meters and microphones were employed to measure and study the sound waves at different distances from the glass tube opening and at the focusing point of the TA laser pair for different laser position arrangements. The sound waves of the two TA lasers at the focusing point were found to be almost 180 degrees out of phase when the openings of the two lasers were very close to each other and the angle between the laser axes was small. When the two TA lasers were placed far apart, the sound wave amplitudes and the phase difference between the two laser outputs varied periodically with time. The frequencies of the sound waves changed when the openings of the two TA lasers were in close vicinity and the angle between the laser axes exceeded a certain value. In this case, the glass tube opening was no longer a pressure anti-node and the wavelength of the fundamental mode was not equal to four times the tube length.

• 전력전자학회논문지
• /
• 제16권3호
• /
• pp.302-308
• /
• 2011

현재 철도 차량용 공조 시스템은 3상 AC 380V를 입력으로 받아 온/오프 제어만 하고 있어 효율 저감 및 소음 등의 문제점을 가지고 있으며 AC 전원 공급이 차단될 경우 blower 동작이 멈추는 문제점을 가지고 있다. 본 논문에서는 UPS 기능을 갖는 A/C blower용 인버터 시스템을 제안한다. 제안한 인버터 시스템은 입력으로 AC 전원과 DC 전원을 받아서 blower 구동용 유도전동기의 V/F 제어를 하며, CAN통신을 이용하여 속도, 모드 및 Soft-Start 시간 등을 제어한다. 또한 CAN 통신 고장시에는 정비용으로 RS-232통신을 이용해서도 제어할 수 있고 조작자가 직접 하드웨어적으로 제어할 수도 있어 기존의 문제점을 보완할 수 있다. 시뮬레이션과 실험을 통해 제안한 인버터 시스템의 유용성을 입증한다.

• Journal of Electrical Engineering and Technology
• /
• 제13권3호
• /
• pp.1251-1264
• /
• 2018

The systematic and effective design method of a Class-D current-source resonant inverter for use in an induction cooker with zero-ripple line current is presented. The design procedure is based on the principle of the Class-D current-source resonant inverter with a simplified load network model that is a parallel equivalent circuit. An induction load characterization is obtained from a large-signal excitation test-bench based on parallel load network, which is the key to an accurate design for the induction cooker system. Accordingly, the proposed scheme provides a systematic, precise, and feasible solution than the existing design method based on series-parallel load network under low-signal excitation. Moreover, a zero-ripple condition of utility-line input current is naturally preserved without any extra circuit or control. Meanwhile, a differential-mode input electromagnetic interference (EMI) filter can be eliminated, high power quality in utility-line can be obtained, and a standard-recovery diode of bridge-rectifier can be employed. The step-by-step design procedure explained with design example. The devices stress and power loss analysis of induction cooker with a parallel load network under large-signal excitation are described. A 2,500-W laboratory prototype was developed for $220-V_{rms}/50-Hz$ utility-line to verify the theoretical analysis. An efficiency of the prototype is 96% at full load.

• 한국안전학회지
• /
• 제24권4호
• /
• pp.28-33
• /
• 2009

This study examined the mounting status of cigar lighter receptacles for vehicles and analyzed the tracking phenomenon that occurs when foreign material entered a cigar lighter receptacle to obtain data for the analysis of accident investigation. Regardless of the vehicle's output, cigar lighter receptacles are mounted in a vehicle horizontally, vertically, or at tilting or inclined angle. The tilting type cigar lighter receptacle is much easier to use but current leakage resulting from foreign materials (coffee, beverages, water, etc.) falling into the cigar lighter receptacle may cause a fire to start. This study used a vehicle battery (DC 12V) as a power supply for the tracking test and configured its circuit in the same way as that of an electrical device in a vehicle. The tracking phenomenon that occurred in the standby mode of the vehicle exhibited a fine flame and an irregular occurrence of smoke. While this tracking phenomenon was occurring, the leakage current and the reaching distance of the flame were measured to be approximately 930mA and $20{\sim}50cm$, respectively. It is thought that the resultant flame may ignite toluene, dust, cigarettes, etc. It was observed that as the tracking progressed, the internal metal socket melted and a hole was created, the surface of which was also severely carbonized. In addition, the electrical resistance of the carbonized conductive path was measured to be approximately $30{\Omega}$. It is thought that this much resistance may cause local heating when leakage current flows and could ignite any nearby flammable material.

• Journal of Power Electronics
• /
• 제17권4호
• /
• pp.892-904
• /
• 2017

A design of a Class-E inverter with only one inductor and one capacitor is presented. It is operated at the optimal operation mode for domestic cooker. The design principle is based on the zero-voltage derivative switching (ZVDS) of the Class-E inverter with a parallel load network, which is a parallel resonant equivalent circuit. An induction load characterization is obtained from a large-signal excitation test bench, which is the key to an accurate design of the induction cooker system. Consequently, the proposed scheme provides a more systematic, simple, accurate, and feasible solution than the conventional quasi-resonant inverter analysis based on series load network methodology. The derivative of the switch voltage is zero at the turn-on transition, and its absolute value is relatively small at the turn-off transition. Switching losses and noise are reduced. The parameters of the ZVDS Class-E inverter for the domestic induction cooker must be selected properly, and details of the design of the components of this Class-E inverter need to be addressed. A 1,200 W prototype is designed and evaluated to verify the validation of the proposed topology.

• Elastomers and Composites
• /
• 제33권4호
• /
• pp.267-273
• /
• 1998

MDI와 에스테르타입의 폴리올인 EBA, NBA, HA를 각각 반응시켜 이소시아네이트 말단기를 갖는 다양한 우레탄 프리폴리머를 합성하였다. 합성된 프리폴리머는 상온에서는 100% 고형분이었으며, 약 $80^{\circ}C$로 가열하면 용융되어 도포에 적당한 흐름성을 나타내었고, 냉각하면 고화되고 습기와 반응하면서 서서히 경화되었다. 대기중의 습기와 반응하여 경화된 우레탄수지의 인장물성은 폴리올의 구조에 따라 특징적인 거동을 나타내었다. 접착력은 EBA, NBA, HA순의 큰 값을 나타내었으며, 이는 동일한 조건에서 가교된 우레탄수지의 파단에너지와 같은 경향을 나타내었다. 또한, 접착조인트의 파괴는 모두 접착제 자체에서 일어났으며, 시험속도가 증가함에 따라 증가하였다. 이로 미루어, 우레탄 핫멜트 접착제 자체의 강인성이 접착력을 결정하는 주요 요인임을 알 수 있었다.

• 에너지공학
• /
• 제27권4호
• /
• pp.70-79
• /
• 2018

한국중부발전 제주화력본부에서 방류되는 온배수로부터 열원을 회수하여 약 3 km의 원거리에 위치하고 있는 신촌백합영농조합법인의 시설온실에 냉온수를 공급하기 위한 300 RT 용량의 열펌프 시스템을 구축하였다. 원거리 시설로 온배수열을 공급하기 위한 최적화 방안을 도출하였고, 수송관로의 온도와 누수여부를 모니터링하기 위한 설비들이 설치되었다. 본 논문에서는 제주 시설온실 냉난방을 위한 발전소 온배수 활용 열펌프 시스템의 구성과 주요기기에 대해 기술하였다. 2018년 하절기에 열펌프 시스템의 냉방성능을 평가하기 위한 실증운전을 수행하였다. 냉방운전 시 열펌프 시스템의 주요 위치에서 측정된 유체의 온도와 유량, 그리고 냉방 성능계수를 분석하여, 구축된 열펌프 시스템의 안정성과 냉방성능을 검증하였다.

• 한국산학기술학회논문지
• /
• 제20권4호
• /
• pp.464-469
• /
• 2019

테이퍼 롤러 베어링은 큰 부하 하중이 가해져도 안정적으로 차량을 지지할 수 있어서 승합차, 화물차, 열차 등에 핵심적인 구동 부품으로 광범위하게 사용된다. 테이퍼 롤러 베어링 부품 중에서 케이지는 롤러들 사이의 간격을 유지해 주며, 이를 통해서 마찰 방지 및 마모, 발열을 억제하고 윤활을 위한 공간을 제공해주는 등의 역할을 한다. 차량이 주행 중에 공진으로 인해 케이지가 심하게 변형되면 롤러가 원활한 구름 운동을 하지 못하거나, 케이지를 이탈하는 경우가 발생하게 된다. 따라서 베어링의 안정적인 내구성능을 확보하기 위해서는 케이지의 공진주파수를 파악하는 것이 매우 중요하다. 베어링 케이지는 구조적으로 동일한 형상이 반복되는 주기적 구조물로 볼 수 있는데, 이러한 구조물은 제작과정에서 설계 시 의도한 완벽한 기하학적 형상과는 어느 정도의 오차를 가진 형상으로 제작되게 된다. 본 연구에서는 이러한 케이지의 기하학적 불완전성이 동특성에 미치는 영향을 파악하고자 한다. 그 결과 기하학적인 불완전성에 의하여 이상적인 케이지의 고유진동수 부근에서 고유진동수 분리가 발생하며, 그 간격은 기하학적 오차의 크기에 비례하고 모드의 차수가 증가할수록 그 간격도 넓어진다고 판단된다.

• Computers and Concrete
• /
• 제26권6호
• /
• pp.467-482
• /
• 2020

This research focused on analyzing the post-fire behavior of high-performance concrete-filled steel tube (CFST) columns, with the concrete containing tire rubber and steel fibers, under axial compressive loading. The finite element (FE) modeling of such heated columns containing recycled aggregate is a branch of this field which has not received the proper attention of researchers. Better understanding the post-fire behavior of these columns by measuring their residual strength and deformation is critical for achieving the minimum repair level required for structures damaged in the fire. Therefore, to develop this model, 19 groups of confined and unconfined specimens with the variables including the volume ratio of steel fibers, tire rubber content, diameter-to-thickness (D/t) ratio of the steel tube, and exposure temperature were considered. The ABAQUS software was employed to model the tested specimens so that the accurate behavior of the FE-modeled specimens could be examined under test conditions. To achieve desirable results for the modeling of the specimens, in addition to the novel procedure described in this research, the modified versions of models presented by previous researchers were also utilized. After the completion of modeling, the load-axial strain and load-lateral strain relationships, ultimate strength, and failure mode of the modeled CFST specimens were evaluated against the test data, through which the satisfactory accuracy of this modeling procedure was established. Afterward, using a parametric study, the effect of factors such as the concrete core strength at different temperatures and the D/t ratio on the behavior of the CFST columns was explored. Finally, the compressive strength values obtained from the FE model were compared with the corresponding values predicted by various codes, the results of which indicated that most codes were conservative in terms of these predictions.

• 한국초전도ㆍ저온공학회논문지
• /
• 제9권1호
• /
• pp.18-21
• /
• 2007

Highly textured MgO template by ion-beam-assisted deposition(IBAD) was successfully fabricated using a continuous reel-to-reel(R2R) mode. To enlarge the deposition area, the previous IBAD system was modified into the system with 14-pass and five heating zone. Every processing step was carried out using this multi-turn IBAD system. The overall process consists of R2R electropolishing of a hastelloy C276 tape, deposition of $Al_2O_3$ diffusion barrier, $Y_2O_3$ seed layer, IBAD-MgO and homoepi-MgO layer. The IBAD-MgO templates were fabricated using the IBAD system with 216 cm-length deposition zone and 32 cm diameter ion source. The texture of MgO films developed during the IBAD process was monitored by in-situ reflection high energy electron diffraction(RHEED) to optimize the IBAD process. Recently, 100 m long IBAD-MgO tape with in-plane texture of $\Delta{\phi}<10^{\circ}$ was successfully fabricated using the modified IBAD system. In this report, the detailed deposition condition of getting a long length IBAD-MgO template with a good epitaxy is described.