• 한국초전도ㆍ저온공학회논문지
• /
• 제2권2호
• /
• pp.15-19
• /
• 2000

The stability of variable cross-sectional area HTS current lead is considered. The cross-sectional area is varied to have a constant safety factor which is defined as the ratio of operating current and critical current of superconductor. As the constant area HTS lead, the variable cross-sectional area HTS lead also has three steady states above the bifurcation point and only one steady state below the bifurcation point. The temperature profiles and current sharing ratios for each steady state are calculated. The heat dissipation into cryogenic system for super-conducting, intermediate, and upper states are compared. For Bi-2333 sheathed with silver-gold alloy 2m length of current lead, and the maximum temperature of upper state seems to be burn-out free below 5m length.

• 한국주조공학회지
• /
• 제10권5호
• /
• pp.399-407
• /
• 1990

The effect of thermal cycling and isothermal exposure on the high temperature microstructural stability of unidirectionally solidified $Al-CuAl_2$ eutectic composite has been studied. A coarsening procedures of lamellar eutectic structures were initiated at growth fault region because of diffusion through low angle boundary at this region. It was considered that thermally induced residual stresses produced by thermal cycling were high enough to increase the dislocation density in Al-rich matrix phase. However, it was also considered that dislocations generated by these high thermal stresses were annihilated at high temperature by stress relaxation. Consequently, the thermal cycling up to 1440 cycles between 20 and $520^{\circ}C$ did not affect the microstructural stability.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.93-93
• /
• 2011

Nanostructures consisting of $TiO_2$ particles as a core and carbon as a shell ($TiO_2$@C) were prepared by heat treatment of $TiO_2$ nanoparticles at high temperature in a methane atmosphere. X-ray diffraction and transmission electron microscopy showed that a carbon shell layer was formed well. These structures were used as supports for platinum nanoparticles and the hybrid particles exhibit improved catalytic activity and stability toward ORR compared to Pt on a carbon black (Vulcan XC-72R). It is likely that enhanced catalytic properties of the Pt on $TiO_2$@C could be due to the stability of the core-shell support in comparison with carbon black support.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.185-190
• /
• 2011

The important use of the desuperheater(multi spray type) changes the superheated steam into the saturated steam. It is more efficient and suitable for using the process. Also, it is more convenient and stable regarding the process temperature control. In this study, transient and quasi-static analysis were done for the evaluation of structural integrity of the multi spray type desuperheater of the power plant. Computational analysis was used to calculate the thermal stress, and the vibration test was done to evaluate the structural stability. This paper is verified by analysis that water spray nozzle(${\phi}=28mm$) shows the best ability. The results show that structural stability of the desuperheater under the real operating condition was proven.

• Restorative Dentistry and Endodontics
• /
• 제16권1호
• /
• pp.1-5
• /
• 1991

The purpose of this study was to investigate the color stability of 2 light - polymerized veneer resins and 3 heat - polymerized veneer resins. Five specimen discs of each brand were immersed in distilled water at $37^{\circ}C$, in darkroom for 120 days. The distilled water was changed on every third day to prevent contamination from micro - organisms. The color characteristics of all the samples were measured by computer controlled spectrophotometer. The appearence was characterized by means of the $L^*$, $a^*$ and $b^*$ uniform color space(CIELAB) and total color difference was calculated. The following results were obtained 1) ${\Delta}E^*ab$ - value in all brand except IS is were greater than 1 perceptable in visual evaluation. 2) ${\Delta}E^*ab$ - value in VI, IS and VG were lower than upper limit of acceptablilty(3.3 in ${\Delta}E^*ab$). DC was the worst in color stability and was changed into yellow color.

• The Korean Journal of Ceramics
• /
• 제1권4호
• /
• pp.219-223
• /
• 1995

Ceramic membranes of the supported $TiO_2-CeO_2$ were prepared by dip-coating method on an $\alpha-Al_2O_3$ porous substrate. The mean pore diameter of an alumina support was 0.125 um. The mean particle diameter of $TiO_2-CeO_2$ top layer varied with firing temperature and ranged from 20 to 85 nm. The thermal stability of the composite membranes was studied from their surface microstructure after calcination at $600-900^{\circ}C$. The supported $TiO_2-CeO_2$ composite membranes exhibited much higher heat resistance than the $TiO_2$ membrane.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.587-589
• /
• 2000

In this paper, the stability criterion for cryocooler-cooled high-temperature superconducting (HTS) coils is discussed. We choose the current, Itr at which "thermal runaway" occurs, as a stability criterion and adopt the relationship between the cooling power of GM cryocooler and the heat generation in coil system to evaluate Itr. We also investigate the transient behavior during a quench process in HTS coils by a newly developed FEM computer program.

• 한국초전도ㆍ저온공학회논문지
• /
• 제19권3호
• /
• pp.8-12
• /
• 2017

If the part of the HTS magnet is exposed to the outside of the cryogenic coolant due to the fluctuation of the height of the cooling liquid or the vapor generation, the uncooled part becomes very unstable. In this paper, the unstable equilibrium temperature distribution of the uncooled part of a superconductor is obtained, and the maximum temperature and energy are calculated as a function of the uncooled length. Similar to the superconductor stability problem, the current sharing model was applied to derive the theoretical formula and calculated by numerical integration. We also applied a jump model, which assumes that joule heat is generated in all of the uncooled segment, and compares it with the current sharing model results. As a result of the analysis, the stable equilibrium state and the critical uncooled length in the jump model are not shown in the current sharing model. The stability of the conductors to external disturbances was discussed based on the obtained temperature distribution, maximum temperature, and energy.

• 한국전기전자재료학회논문지
• /
• 제27권12호
• /
• pp.776-791
• /
• 2014

A marvellous solar cell technology system based on organometal halide perovskites has recently shown an unprecedented progress in power conversion efficiency (PCE); the certified one of 17.9% and unconfirmed of 19.3%, as well as the estimated electricity with a generating cost lower than the half of conventional methods based on fossil fuels. In this report the present status of stability with regards to moisture, ambient temperature, ultraviolet and lead toxicity as well as the key technological developments for the early commercialization are covered. Comprehensive understanding of material science for perovskites is required, together with complete encapsulation technologies beyond those for OLEDs, in order to ensure a 20-year-longer-than lifetime of PSCs (perovskite solar cells) and the stability according to the IEC 61646 damp heat test standard, which will result in the replacement of silicon solar cells with PSCs.

• 한국재료학회지
• /
• 제16권10호
• /
• pp.614-618
• /
• 2006

The thermal stability of Cu/Ti(or Ta)/NiSi contacts was investigated. Ti(Ta)-capping layers deposited to form NiSi was utilized as the Cu diffusion barrier. Ti(Ta)/NiSi contacts was thermally stable upto $600^{\circ}C$. However when Cu/Ti(Ta)/NiSi contacts were furnace-annealed at $300{\sim}400^{\circ}C$ for 40 min., the Cu diffusion was found to be effectively suppressed, but NiSi was dissociated and then Ni diffused into the Cu layer to form Cu-Ni solutions. On the other hand, the Ni diffusion did not occur for the Al/Ti/NiSi system. The thermal instability of Cu/Ti(Ta)/NiSi contacts was attributed to the high heat of solution of Ni in Cu.