• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.1
• /
• pp.109-116
• /
• 2014

This paper presents a high-efficiency digital class-D audio amplifier using a composite interpolation filter for portable audio devices. The proposed audio amplifier is composed of an interpolation filter, a delta-sigma modulator, and a class-D output stage. To reduce power consumption, the designed interpolation filter has an optimized composite structure that uses a direct-form symmetric and Lagrange FIR filters. Compared to the filters with homogeneous structures, the hardware cost and complexity are reduced by about half by the optimization. The coefficients of the digital delta-sigma modulator are also optimized for low power consumption. The class-D output stage has gate driver circuits to reduce shoot-through current. The implemented class-D audio amplifier exhibited a high efficiency of 87.8 % with an output power of 57 mW at a load impedance of $16{\Omega}$ and a power supply voltage of 1.8 V. An outstanding signal-to-noise ratio of 90 dB and a total harmonic distortion plus noise of 0.03 % are achieved for a single-tone input signal with a frequency of 1 kHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.3
• /
• pp.44-53
• /
• 2008

In this paper, we present the design of delta-sigma modulation-based class-D amplifier for driving headphones in portable audio applications. The presented class-D amplifier generates PWM(pulse width modulation) signals using a single-bit fourth-order high-performance delta-sigma modulator. To achieve a high SNR(signal-to-noise ratio) and ensure system stability, the locations of the modulator loop filter poles and zeros are optimized and thoroughly simulated. The test chip is fabricated using a standard $0.18{\mu}m$ CMOS process. The active area of the chip is $1.6mm^2$. It operates for the signal bandwidth from 20Hz to 20kHz. The measured THD+N(total harmonic distortion plus noise) at the $32{\Omega}$ load terminal is less than 0.03% from a 3V power supply.

• Korean Journal of Optics and Photonics
• /
• v.10 no.2
• /
• pp.146-151
• /
• 1999

We demonstrated a harmonic mode locking scheme that used regeneratie phase modulation to get a high and stable repetition rate in a figure-of-eight fiber soliton laser. From the detected beat spectra of the laser output, a sinusoidal clock freguency tone of 400 MHz, the 96th harmonics of the fundamental mode locking frequency, was extracted with a high Q filter and was used to drive the phase modulator, resulting in stable output of soliton pulse train synchronized with the modulation signal. Generated soliton pulses had FWHM pulsewidth of 930 fs and 3.1 nm linewidth, yielding pulsewidth-bandwidth product of 0.359 that was close to the transform limit. As the modulation frequency always followed the beat frequency of laser modes, stable harmonic mode locking was achieved without the adjustment of the cavity length, which has been commonly required in actively mode-locked lasers.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.97-104
• /
• 1999

Brake squeal noise has been a problem since the early days of motoring . It is important to obtain vibration mode shape for reduction of brake noise . Stroboscopic Electronic Speckle Pattern Interferometry is a very powerful measuring method for study of vibrating objects in static state compared with conventional methods because this method can give both resonance frequency and quantitative visualization of vibration mode shape at the same time. In this paper, we performed qualitative visualization and quantitative analysis of vibration mode shpae of disk brake by using stroboscopic ESPI and phase shifting method. The stroboscopic wavefronts are obtained by chopping continuous wave laser beam using acousto-optic modulator .Experiments were performed at the same constraint conditions as disk brake of the practical vehicle as far as possible. The experimental results of this paper show quantitative measurement of vibration mode shape and quantiative visualization of vibration amplitude of disk brake with 3D plotting.

• Journal of Power Electronics
• /
• v.4 no.3
• /
• pp.152-160
• /
• 2004

This paper presents analysis, modeling, and design of a low-harmonic, isolated, active-clamped SEPIC for future avionics applications. Simpler converter dynamics, high switching frequency, zero voltage-Transition-PWM switching, and a single-layer transformer construction result. This paper describes complete design of a digital controller for a high-frequency switching power supply. Guidelines for the minimum required resolution of the analog-to-digital converter, the pulse-width modulator, and the fixed-point computational unit is derived. A design example based on a SEPIC converter operating at the high switching frequency is presented. The controller design is based on direct digital design approach and standard root-locus techniques.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.6
• /
• pp.608-614
• /
• 2015

A multi-channel audio CODEC with inter-channel interference suppression is proposed, in which channel switching noise-referred sampling error is significantly reduced. It also supports a coarse/fine mode operation for fast frequency tracking with good harmonic performance. The proposed multi-channel audio CODEC was designed in a 65 nm CMOS process. Measured results indicated that SNR and SNDR of ADC were 93 dB and 84dB, respectively, with SNDR improved by 43 dB. Those of DAC were 96 dB and 87 dB, respectively, with SNDR improved by 45 dB when all the channels are running independently.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1321-1323
• /
• 2000

Sigma-delta modulation can perform A/D conversion with a high-resolution. It is useful for simplifing the system and spreading out inband signal noise. When the sigma-delta modulation is applied to a switching converter, it can suppress the harmonic frequencies of output signal and be realized with a simple structure. In this paper, some methods of sigma-delta modulation are discussed so as to find the suitable structure for a switching converter. Noise characteristics are calculated and analyzed through simulations.

• Journal of Institute of Convergence Technology
• /
• v.11 no.1
• /
• pp.7-12
• /
• 2021

The magnetic gear, which amplifies the torque by filtering the magnetic field generated by the low-speed permanent magnet with a modulator, can exclude gear contact and can be effectively applied when there are environmental restrictions. In this paper, we discuss the magnetic force characteristics of a magnetic gear using a magnetic focusing array that replaces a general permanent magnet array magnetized in a radial direction along the circumferential direction. The torque increasing effect of the discussed array, known as an arrangement that increases the principal component by focusing a radial magnetic field, is compared with that of a general magnetic gear. In particular, in a magnetic gear using such an array, the sensitivity of torque according to variables is analyzed to see how various variables known as factors affecting torque have an effect.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.1 s.104
• /
• pp.45-51
• /
• 2006

In this paper, a new predistortion linearizer for controlling the amplitude of low frequency intermodulation distortion signals is proposed. The low frequency intermodulation distortion(IMD) components are generated by harmonic generator. A vector modulator, modulate fundamental signal with low frequency IMD signals, generates predistortion IMD signals and controls amplitude and phase of them with modulation factors. As a result, this predistorter is suppressed IMD signals of power amplifier effectively. The predistortion linearizer has been manufactured to operate in cellular base-station transmitting band($869{\sim}894\;MHz$). The experimental results show that IMD3 of power amplifier are improved more than 20 dB for CW two-tone signals. Also, it's improved the adjacent channel power ratio(ACPR) more than 10 dB for IS-95 CDMA IFA signals.

• Korean Journal of Materials Research
• /
• v.7 no.3
• /
• pp.213-217
• /
• 1997

AOhf(Hcousto-r)l)tic niodulator) with :!OOlIiz freclucncl- and Sfi(;(Seconrl harmonic generation) green lasel-Lvith 53% nm wavelength were used for Il\'IIII~Dii.it,ii v~ilco disk recorder) FOI rhe appli~aptin of high densit]. optical recording, a high po\ver I ~ c r is r c ~ ~ l i ~ i l - u l ic I !tic. s\-sti,m a n d optic.,~I io;iting l,t)c>rs of each optical device must have a high laser damage threshoid hie rn;itie ant] retlwtive coatings on a $TeO_{2}$ singlc crystal. which is used as an acoustooptic material, by E-beam evaporation method. Laser damage threshold \vas nicdsureci hy Ar laser with the input power oi 0.55LV 1,aser damage threiholti 01 $ZrO_{2}$ and $SiO_{2}$. filn-is were higher than $AI_{2}O_{3}$ f i l m U'e also investigated a long--tern1 stability of the output po\ver of St{(; green laser