• 한국결정성장학회지
• /
• 제1권1호
• /
• pp.60-65
• /
• 1991

The hydrothermal growth of $GaPO_{4}$ Single Crystals was carried out by the horizontal temperature gradient method. The most promising solvents for the crystal growth of $GaPO_{4}$ are $H_{3}PO_{4}$ and HCl solutions. Single crystals have been hydothermally grown at temperatures over the range $210-290^{\circ}C$ in these solutions with seed crystals. The glowth rates in HCl solution were higher than that for comparable conditions in $H_{3}PO_{4}$ solution. Morphologies of crystals grown at temperatures below $200^{\circ}C$ tended to be bounded by small major rhombohedral(10$\bar{1}$1) faces. In the temperature range from 200 to $430^{\circ}C$, the single crystals have morphologies bounded by prism (10$\bar{1}$0), small major rhombohedral(10$\bar{1}$1) and minor rhombohedral(01$\bar{1}$1) faces at the early stage, and grew with well developed basal(0001) faces by increasing the growth temperature.

• 한국운동역학회지
• /
• 제31권4호
• /
• pp.283-289
• /
• 2021

Objective: The aim of this study was to analyze the pattern of Kolman technique by five Korean top gymnasts including the three national athletes on horizontal bar. Method: Two digital high-speed camcorders were used with 90 frames/sec and their Kolman motions were filmed in sports science secondary school gymnasium at U city. After the kinematic and kinetic variables were carried out by Kwon3D 3.1 motion package during the whole phase, the optimized release motion was investigated by simulating the body COG path during the aerial phase. Results: Firstly, it was revealed that the average changes of hip, shoulder joint angle were 84 deg, 53 deg respectively during the functional sub-phase and the average swing phaseal time was 1.21 s. Secondly, it was revealed that the average body COG positions and velocities (Y, Z) at release were -0.65 m, 0.48 m, 1.65 m/s, 3.97 m/s respectively and the average release angle, peak height and flight time were 67 deg, 1.29 m, 0.79 s respectively. Thirdly, it was revealed that the directions of somersault of whole and lower body, tilt of lower body were counterclockwise, whereas the directions of tilt of whole body, twist of whole and lower body were clockwise at the ready for re-grasp. Lastly, it was revealed that the body COG paths were different from each other during the aerial phase followed by the different body COG velocities. Conclusion: Korean gymnasts of this study controlled their motions well in terms of the timing of hip·shoulder joint, body position, body angular momentum especially during the functional sub-phase, but their motions were different during the aerial phase. Nonetheless most of them made the adequate body position at the instant of re-grasp. It would be suggested that Korean gymnasts except S3 should increase the vertical velocity.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.261-264
• /
• 1997

A single action press robot, which consists of a driving unit, rotator, up-down feed base and feed bar, is developed and applied for the press automation. The driving unit is made up with a face cam and blade cam, which have a phase angle. The feeding system consists of a double speed-up apparatus and linear motion guides, and has a fast motion characteristics. A horizontal feeding speed of the feed bar is increased twice by the double speed-up apparatus. The driving mechanism could be simplified due to the speed-up of the feeding unit.

• 천문학논총
• /
• 제28권3호
• /
• pp.55-63
• /
• 2013

동아시아에서 규표는 가장 전통적인 천문의기 중 하나였다. 그럼에도 불구하고 고전적 규표는 표의 수직 설치와 유지가 어렵고, 눈금의 시작점이 모호하였으며, 무엇보다도 태양의 표 그림자가 퍼져 관측의 정밀성이 떨어졌다. 이러한 고전적 규표의 단점을 해결하고자 하는 노력의 결과물로 13세기에 횡량형 규표가 개발되었다(민병희 등, 2011). 횡량형 규표는 영부를 사용하여 선명한 횡량 그림자를 얻었다. 영부를 통해 얻은 횡량 그림자는 예리하여 관측의 모호성이 없으며, 동시에 태양의 중심 위치를 관측하는 최적의 천문의기이었다. 대규표는 횡량을 설치하였는데, 이 횡량의 크기는 길이 6자(124.2 cm), 직경 3치(6.21 cm)이었다. 표 기둥 위에 횡량을 올린 것을 얼이라고 하고, 이 얼을 수직으로 설치하는 것이 횡량형 규표의 핵심이었다. 삼점현추법을 사용하여 얼을 규에 수직으로 세울 수 있었다. 삼점현추법을 사용하기 위해 횡량은 길이 5치(10.35 cm), 직경 2푼(4.14 mm)의 철사 3개를 이용하고 있다. 삼점현추법은 단지 횡량을 정렬하는데 만 필요한 것이 아니고, 횡량을 점검하고 진단하는데도 활용되었다. 횡량의 개발은 태양 중심의 그림자길이를 측정하는 천문학적 이점과 더불어 규표의 대형화를 가능하게 하였다. 규표의 적절한 건설 공정과 삼점현추법을 적용하면 이상적으로는 높이에 무관하게 얼을 수직하게 설치할 수 있었기 때문이다. 얼의 크기가 높아질수록 결과적으로 눈금의 분해능을 증가시킬 수 있기 때문에(이용삼 등, 2006) 관측의기의 성능을 향상시킬 수 있었다.

• 대한물리치료과학회지
• /
• 제3권4호
• /
• pp.147-152
• /
• 1996

Therapeuticre rehabilitation of young children has often included the use of walker as mobility aids. Traditional walkers have four vertical legs, a horizontal bar in front of child, and horizontal bars on either side which also serve as hand grip. Child pushes it. It is called 'anterior walker'. 'Posterior walker' have been introduced which the child pull along behind himself during ambulation. The purpose of this investigation was to compare specific gait characteristics of children with developmental disability, while they ambulated with anterior and posterior walker. Using the posterior walker, specific gait characteristics improve than using anterior walker.

• 지구물리
• /
• 제2권2호
• /
• pp.135-142
• /
• 1999

선형 자기쌍극자 모델의 하나인 철근에 대하여 3성분 자력계를 이용한 자력검층을 실시한 후 검층자료를 최소 자승법에 의한 역산을 이용하여 해석하였다. 본 실험에 사용된 철근의 길이는 1.12 m, 샘플링 간격은 0.05 m, 자력계와 철근사이의 거리는 0.3 m이며, 철근의 상단부를 깊이 0 m 지점에 고정하였다. 철근은 연직에 가깝도록 위치시켰다. FFT를 이용하여 평활화한 자기이상을 역산의 입력자료로 활용하였다. 검층자료의 해석을 위하여 선형 자기쌍극자의 상단부 심도, 길이, 단위 길이 당 자기모멘트, 자화방향(편각 및 복각), 경사방향과 경사각 등을 미지수로 설정하였다. 자기이상의 수평성분 및 수직성분 각각에 대한 역산 결과와 수평성분과 수직성분을 동시에 고려한 역산 결과를 비교하였는데 각각의 역산결과는 다소 차이를 보인다. 자기이상의 수평성분과 수직성분을 동시에 고려하여 역산을 수행하는 것이 각각의 성분을 역산하는 경우보다 정확한 해석이 가능한 것으로 판단된다. 이 때 철근 하단부의 추정 심도는 1.18 m로, 실제 심도인 1.12 m에 매우 근접하며, 철근의 복각은 -76°로 추정되었다. 철근의 복각이 음(-)의 값을 갖는 것은 철근의 유도자화 강도에 비하여 잔류자화 강도가 훨씬 커서, 전체적인 자화 방향이 철근의 상단 방향을 향하고 있기 때문으로 해석된다.

• 한국운동역학회지
• /
• 제16권3호
• /
• pp.65-74
• /
• 2006

This study was attempted to Kinematical characteristics of the Endo $360^{\circ}$El-grip Swing on the horizontal bar. To do this, we selected and analyzed the performance of two athletes who did Endo $360^{\circ}$El-grip Swing in the horizontal bar competition of male artistic gymnastic in the 22nd Universiad Games 2003 Daegu. We drew the conclusions from the kinematical factors that were came out through analyzing three-dimensional cinematography of the athletes' movements, by using two video cameras. In point of analyzing the actual competition situation, it is expected that gymnastics and coaches have the effective informations, and the following conclusion had resulted. 1. When performing Endo $360^{\circ}$El-Grip, the average for entire required time was $1.93{\pm}0.06sec$. The average for descent phase time was $0.24{\pm}0.02sec$, ascent phase time was 0.22${\pm}0.07sec$, connecting phase time was $0.87{\pm}0.07sec$, and El-Grip phase time was $0.61{\pm}0.02sec$. The descent phase need short period of time but however to have a stable performance, ensuring ascent and connecting phase time are needed. El-Grip phase need short period of time to have a stable re-grasp. 2. To have a convenient preparation for El-Grip in descent and ascent phase, lowering CM, and ease up in sway and plunge from the High Bar would make descent and ascent even more faster and would have increase effect in trunk rotation. 3. In descent and ascent phase, if shoulder angle and arm slope is dwindling then it would effect rotation angle so might risk it from hitting a Bar when putting legs in and out. 4. In connecting phase, it requires some time to show stable performance when El-Grip phase is continued by using hip angle which would make trunk rotation angle bigger and make descent and ascent time slower. 5. In El-Grip phase, when doing motions like hand standing. using hip angle more than maximum would make CM even faster and it is stable position while performing.

• The Journal of Advanced Prosthodontics
• /
• 제6권1호
• /
• pp.39-45
• /
• 2014

PURPOSE. The aim of the present study was to evaluate the accuracy of three techniques for correction of cast implant bars. MATERIALS AND METHODS. Thirty cast implant bars were fabricated on a metal master model. All cast implant bars were sectioned at 5 mm from the left gold cylinder using a disk of 0.3 mm thickness, and then each group of ten specimens was corrected by gas-air torch soldering, laser welding, and additional casting technique. Three dimensional evaluation including horizontal, vertical, and twisting measurements was based on measurement and comparison of (1) gap distances of the right abutment replica-gold cylinder interface at buccal, distal, lingual side, (2) changes of bar length, and (3) axis angle changes of the right gold cylinders at the step of the post-correction measurements on the three groups with a contact and non-contact coordinate measuring machine. One-way analysis of variance (ANOVA) and paired t-test were performed at the significance level of 5%. RESULTS. Gap distances of the cast implant bars after correction procedure showed no statistically significant difference among groups. Changes in bar length between pre-casting and post-correction measurement were statistically significance among groups. Axis angle changes of the right gold cylinders were not statistically significance among groups. CONCLUSION. There was no statistical significance among three techniques in horizontal, vertical and axial errors. But, gas-air torch soldering technique showed the most consistent and accurate trend in the correction of implant bar error. However, Laser welding technique, showed a large mean and standard deviation in vertical and twisting measurement and might be technique-sensitive method.

• Earthquakes and Structures
• /
• 제19권6호
• /
• pp.459-469
• /
• 2020

An external prestressed steel-bar truss unit was developed as a new strengthening technology to enhance the seismic performance of an in-plane masonry wall structure while taking advantage of the benefits of a prestressed system. The presented method consists of six steel bars: two prestressed vertical bars to introduce a prestressing force on the masonry wall, two diagonal bars to resist shear deformation, and two horizontal bars to maintain the configuration. To evaluate the effects of this new technique, four full-scale specimens, including a control specimen, were tested under combined loadings that included constant-gravity axial loads and cyclic lateral loads. The experimental results were analyzed in terms of the shear strength, initial stiffness, dissipated energy, and strain history. The efficiency of the external prestressed steel-bar truss unit was validated. In particular, a retrofitted specimen with an axial load level of 0.024 exhibited a more stable post behavior and higher energy dissipation than a control specimen with an observed complete sliding failure. The four vertical bars of the adjacent retrofitting units created a virtual column, and their strain values did not change until they reached the peak shear strength. The shear capacity of the masonry wall structure with external prestressed steel-bar truss units could be predicted using the model suggested by Yang et al.

• 한국운동역학회지
• /
• 제19권1호
• /
• pp.37-47
• /
• 2009

본 연구는 체조 철봉종목의 국가대표선수 2명을 대상으로 고난도 공중 비행 기술인 콜만 동작의 완성도를 높이기 위한 기술훈련 프로그램을 개발하여 8주간 적용하고 향상도를 3차원 영상분석을 통해 제시함으로써 경기력 향상에 도움을 주고자 하였다. 훈련 프로그램은 휘돌기 손 놓기, twist, 봉잡기로 구성하여 실시하였으며, 그 결과 다음과 같은 결론을 얻었다. 동작이 처음 시작되는 크게 휘돌기의 물구나무 경과 시 신체를 지면과 수직에 가깝도록 치켜세운 다음 수직하강에 가깝게 신체를 다운시켜서 깊은 추기기 운동을 수행케 하고, 고관절과 견관절의 굴신 폭을 크게 하는 추기기보다는 우선적으로 동체 회전을 중시하면서 신체중심을 충분히 끌어 올리는 봉 이탈, 그리고 비행 시 신체 각 관절의 상대각을 작게 하도록 주문하여 연습케 하였다. 그 결과 철봉의 탄성을 크게 유발하구 신체의 후방 진행속도를 증가시켜서 휘돌기의 구심력을 증가시키면서 높은 위치에서 봉을 이탈하였으며, 비행 시 신체를 빠르게 지면과 수직이 되도록 세울 수 있게 되어 여유로운 공중회전과 비틀기 운동을 수행할 수 있었다. 또한 상승할 때 손 놓는 타이밍을 맞추는데 특별히 신경 쓰지 않더라도 비행방향의 조절을 용이하게 할 수 있어서 봉잡기 시 철봉과 적정한 거리를 유지함과 동시에 충분한 동체의 회전과 비틀기 거리를 확보할 수 있었다.