• 한국세라믹학회지
• /
• 제48권1호
• /
• pp.80-85
• /
• 2011

The crystallization behavior and microstructural change of the glass-ceramics were analyzed as a function of concentration and etching time of the HF solution in order to enhance the degree of crystallinity induced by heterogeneous nucleation of glass of bottom ash containing 15 wt% $Li_2O$. The nucleation site seemed to be generated where the Si ion was eluted. The main crystal phases in the glass-ceramics fabricated in this study were $\beta$-spodumene and $Li_2SiO_3$. The specimens etched with HF of 0.5 vol% within 0~60 seconds showed increased crystalline peak intensities in XRD pattern with etching time compared to no-etched one. Also the crystal size and crystal occupancy in the glass matrix observed by SEM were increased with etching time. For the glass-ceramics etched with 1.0 and 2.0 vol% HF solution, the etching time over 10 s was not effective to increase the crystallinity. From this study, it was found that the glass-ceramics with the higher crystallinity could be obtained by HF-etching followed by heat treatment process, even though the nucleating agent or 2-stages thermal treatment process were not used.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.725-730
• /
• 1996

The key process in silicon surface micromachining is the selective etching of a sacrificial layer to release the silicon microstructure. The newly developed anhydrous HF/$CH_3$OH gas phase etching of TEOS (teraethylorthosilicate) sacrificial layers onto the polysilicon and the nitride substrates was employed to release the polysilicon microstructures. A residual product after TEOS etching onto the nitride substrate was observed on the surface, since a SiOxNy layer is formed on the TEOS/nitride interface. The polysilicon microstructures are stuck to the underlying substrate because SiOxNy layer does not vaporize. We found that the only sacrificial etching without any residual product and stiction is TEOS etching onto the polysilicon substrate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.628-631
• /
• 2003

This study describes a new mastless nano-fabrication technique of Pyrex 7740 glass using the combination of nanomachining by nano-indenter XP and HF wet etching. First, the surface of a Pyrex 7740 glass specimen was machined by using the nano-machining system, which utilizes the mechanism of the nano-indenter XP. Next, the specimen was etched by HF solution. After the etching process, the convex structure or deeper hole is made because of masking or promotion effect of the affected layer generated by nano-machining. On the basis of this interesting fact. some sample structures were fabricated.

• 한국재료학회지
• /
• 제23권6호
• /
• pp.316-321
• /
• 2013

The electrical properties and surface morphology changes of a silicon wafer as a function of the HF concentration as the wafer is etched were studied. The HF concentrations were 28, 30, 32, 34, and 36 wt%. The surface morphology changes of the silicon wafer were measured by an SEM ($80^{\circ}$ tilted at ${\times}200$) and the resistivity was measured by assessing the surface resistance using a four-point probe method. The etching rate increased as the HF concentration increased. The maximum etching rate 27.31 ${\mu}m/min$ was achieved at an HF concentration of 36 wt%. A concave wave formed on the wafer after the wet etching process. The size of the wave was largest and the resistivity reached 7.54 $ohm{\cdot}cm$ at an 30 wt% of HF concentration. At an HF concentration of 30 wt%, therefore, a silicon wafer should have good joining strength with a metal backing as well as good electrical properties.

• 한국전기전자재료학회논문지
• /
• 제14권2호
• /
• pp.117-122
• /
• 2001

In this paper, we report on photoelectrochemical etching process of 6H-SiC semiconductor wafer. The etching was performed in two-step process; anodization of SiC surface to form a deep porous layer and thermal oxidation followed by an HF dip. Etch rate of about 615${\AA}$/min was obtained during the anodization using a dilute HF(1.4wt% in H$_2$O) electrolyte with the etching potential of 3.0V. The etching rate was increased with the bias voltage. It was also found out that the adition of appropriate portion of H$_2$O$_2$ into the HF solution improves the etching rate. The etching process resulted in a higherly anisotropic etching characteristics and showed to have a potential for the fabrication of SiC devices with a novel design.

• 반도체디스플레이기술학회지
• /
• 제16권4호
• /
• pp.16-19
• /
• 2017

For the economical and environmental-friendly fabrication of polisher, Mo mask layer were sputtered on glass substrate instead of Cr mask material. Mo mask layers were sputtered by pulsed-DC sputtering and Photoresist patterns were formed on Mo mask layer for different develop times and optimized. After Mo mask layer were patterned and exposed glass was wet etched by HF solution for different etching times, the remaining Mo mask was stripped by using Al etchant. Develop time of 30 sec and HF wet etching time of 3 min were selected as optimized process condition and applied to the fabrication of polisher.

• 마이크로전자및패키징학회지
• /
• 제15권3호
• /
• pp.41-46
• /
• 2008

본 연구는 2.5MHF-xMHCl$(x:0\sim8)$ 혼합 용액에서 $EAGLE^{2000TM}$ LCD 유리의 식각에 관한 것이다. 유리의 용해공정에서 율속단계는 HF를 함유한 식각액과 유리와의 반응이었다. 그 증거로는 유리의 두께는 시간에 따라 직선적으로 감소하였고, 식각속도는 교반정도에 무관하게 일정하였으며, 활성화 에너지가 $35\sim45$ kJ/mol 범위였다는 점이다. 순수한 HF만 사용했을 때 보다 HCl이 첨가되면 식각속도는 증가하였고. 그 속도는 HCl 첨가량에 비례하여 증가하였다. 또한 HCl 첨가시 식각 후의 표면은 식각 전과 유사하였다. 이는 HCl 첨가에 의해 $H_{3}O^{+}$ 이온의 농도가 증가하여 각종 불화물의 용해도를 증가시키고, $H_{3]O^{+]$ 이온의 흡착은 Si-O 결합의 결합력을 감소시키기 때문에 일어난 현상으로 사료된다.

• 한국정밀공학회지
• /
• 제22권7호
• /
• pp.71-78
• /
• 2005

The purpose of this study is to suggest a hyperfine maskless writing technique by using the nanoindentation and HF wet etching technique. Indents were made on the surface of Pyrex7740 glass by the hyperfine indentation process with a Berkovich diamond indenter, and they were etched in $50\;wr\%$ HF solution. After etching process, convex structure was obtained due to the deformation-induced hillock phenomena. In this study, effects of indentation process parameters (etching time, normal load, loading .ate, hold-time at the maximum load) on the morphologies of the indented surfaces after isotopic etching were investigated from an angle of deformation energies. Finally, sample characters were written to show the possibility of the application.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.225-228
• /
• 2005

The purpose of this study is to investigate effects of the plastic/elastic deformation energy on wet etching characterization on the surface of material by using the nanoindentation and HF wet etching technique. Indents were made on the surface of Pyrex 7740 glass by the hyperfine indentation process with a Berkovich diamond indenter, and they were etched in $50\;wt\%$ HF solution. After etching process, convex structure was obtained due to the deformation-induced hillock phenomena. In this study, effects of indentation process parameters (normal load, loading rate) on the morphologies of the indented surfaces after isotopic etching were investigated from an angle of deformation energies.

• 한국정밀공학회지
• /
• 제21권4호
• /
• pp.24-31
• /
• 2004

The objective of this work is to suggest a mastless pattern fabrication technique using the combination of machining by Nanoindenter(equation omitted) XP and HF wet etching. Sample line patterns were machined on a borosilicate surface by constant load scratch (CLS) of the Nanoindenter(equation omitted) XP with a Berkovich diamond tip, and they were etched in HF solution to investigate chemical characteristics of the machined borosilicate surface. All morphological data of scratch traces were scanned using atomic force microscope (AFM).