• Structural Engineering and Mechanics
• /
• v.63 no.2
• /
• pp.217-223
• /
• 2017

Glass fiber reinforced gypsum panels (GFRG) are hollow panels made from modified gypsum plaster and reinforced with chopped glass fibers. The hollow cores of panels can be filled with in-situ concrete/reinforced concrete or insulation material to increase the structural strength or the thermal insulation, respectively. GFRG panels are unfilled when used as partition walls. As load bearing walls, the panels are filled with M 20 grade concrete (reinforced concrete filling) in order to resist the gravity and lateral loads. The study was conducted in two stages: First stage involves formulation of the alternate light weight mix by conducting experimental investigations to obtain the optimum combination of phosphogypsum and shredded thermocol. In the second stage the alternate mixes are filled in GFRG panels and experimental investigations are conducted to compare the performance against panels filled with conventional M 20 mix.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.36-37
• /
• 2016

Among all the slags, ladle furnace slag (LFS) is reducing slag generated from electric arc furnace. After cooled rapidly by high-pressured air (atomizing technology), LFS has more amorphous phase than slow cooled slag. Therefore, it shows higher reactivity than another recycling slag. This material also is named by rapid cooling LFS (RC-LFS). Pulverized RC-LFS should be fully understood. This paper deal with the present some basic experimental properties and discussions about the setting time of pulverized RC-LFS with different gypsum under the various temperatures. According to the experimental results, the pulverized RC-LFS with gypsum can hydrate in a low-temperature environment, even though the initial and final setting time are delayed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.28-29
• /
• 2015

Although there are many applications with gypsum board because of its economical and construction advantages, four-layer construction technique, (hollow area between two-layer panel sets) is the general case to achieve the insulation, and resistance of horizontally applied force. Since this construction method has many problems such as complicate construction steps and increased cost, it is needed that the two-layer panel for improved construction and economical advantage for lightweight pane: thick panel with favorable performances. Therefore, in this research, based on the ALC panel with 10 to 30mm depth, feasibility of the paper reinforced panel as a lightweight wall material. As a result, favorable performance with increased flexural strength were achieved with paper reinforcement.

• Geomechanics and Engineering
• /
• v.36 no.1
• /
• pp.51-69
• /
• 2024

Currently, composite lining mountain tunnels in China are generally classified based on the [BQ] method for the surrounding rock grade. Increasingly, tunnel field construction is replicated indoors for scale down model tests. However, the development of analogous materials for model tests of composite lining tunnels with different surrounding rock grades is still unclear. In this study, typical Class III and V surrounding rock analogous materials and corresponding composite lining support materials were developed. The whole processes of excavation-support dynamics of the mountain tunnels were simulated. Data on the variation of deformations, contact pressures and strains on the surrounding rock were obtained. Finally, a comparative analysis between model tests and numerical simulations was performed to verify the rationality of analogous material development. The following useful conclusions were obtained by analyzing the data from the tests. The main analogous materials of Class III surrounding rock are barite powder, high-strength gypsum and quartz sand with fly ash, quartz sand, anhydrous ethanol and rosin for Class V surrounding rock. Analogous materials for rockbolts, steel arches are replaced by aluminum bar and iron bar respectively with both shotcrete and secondary lining corresponding to gypsum and water. In addition, load release rate of Class V surrounding rock should be less than Class III surrounding rock. The fenestration level had large influence on the load sharing ratio of the secondary lining, with a difference of more than 30%, while the influence of the support time was smaller. The Sharing ratios of secondary lining in Class III surrounding rock do not exceed 12%, while those of Class V surrounding rock exceed 40%. The overall difference between the results of model tests and numerical simulations is small, which verifies the feasibility of similar material development in this study.

• Korean Journal of Plant Resources
• /
• v.13 no.1
• /
• pp.41-47
• /
• 2000

This study was conducted to evaluate development of seed pellet technique such as pellet polymer search, the shape formation and hardness, the germination and emergence rate of the pellet seeds for labor-saving and reducing production cost in onion(Allium cepa L.) cultivation. The pellet seeds shape formation was good such as kaolin, clay, ash, and gypsum, and clay was good shape formation but surface of pellet seed was cracked during the drying. PG(pearlite + gypsum) as pellet material and PVA as binder were the best among the material in consideration with shape and hardness together. The hardness of the pellet seeds was affected by polymers, the kinds and concentration of binders, and that degree was large at polymer. The high hardness polymers were gypsum and coal ash, but burned lime was the lowest hardness among the pellet material. The germination(GP) and emergence percentage(EP) of pellet seed with PG in vitro were the highest among the material, and that was 93.6, 91.8%, respectively. The EP of pellet seed with PG at 20, $25^{\circ}C$ were 91.3, 92.0%, respectively, The EP of pellet seed were over the 91%, and those did not show difference with field moisture capacity , and that of 5 and 6mm size seed were the highest as 92%, respectively. and other size seeds showed over 90%, too. The EP of pellet seed with PG was decreasing as increasing the sowing depth, and that of at 10mm sowing depth was the highest as 92.7%. The time to 50% emergence of that under 70% field moisture capacity was 158h, and that was delayed at 20h compare to control seed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.4
• /
• pp.673-680
• /
• 1997

NaOH, $Na_2CO_3, CaO, Ca(OH)_2$ and $CaCO_3$ are widely used counteractives for neoutralizing the waste sulphuric acid produced during the metal surface treatment process and/or the metal refining process. To reduce the tremendous expenses for the neutralization treatment of the waste sulphuric acid, the sludge from calcination plant and the stainless refining dust in POSCO (Pohang Iron ＆ Steel co. Ltd.) was utilized. For the sludge, it will be effective to use calcined and then hydrated sludge in strong acid region (pH<2) and to use the sludge itself in weak acid region (pH>2), The gypsum, the by-product of this treatment, was tested to fit the industrial standard of gypsum, so it is expected that it will solve the lack of gypsum supply. For the stainless refining dust, the phase and the morphology of produced gypsum from waste suiphuric acid neutralization was compared with those from pure sulphuric acid. Because of high reactivity and reaction temperature, $CaSO_4$ non-hydrate was obtained in pure sulphuric acid. But $CaSO_4$ dihydrate was obtained in waste sulphuric acid. It is also judged to be a good material for a counteractive of the waste sulphuric acid.

• Journal of the Korean Society of Safety
• /
• v.30 no.6
• /
• pp.40-47
• /
• 2015

In this study, temperature characteristics and fire damage form were analyzed to investigate flame spreading form and fire probability from ignition sources subject to drivit component materials which is finishing material in architecture. Ignition sources were limited to a gas torch and exterior panel board fire, and the size of the sample was manufacture in 30 cm length ${\times}$ 50 cm height ${\times}$ 5cm thickness size. Marble (inner wall) + 3 mm drivit (outer wall), marble (inner wall) + 4 mm plaster stone (outer wall), sandwich panel + 3 mm driver bit (outer wall), sandwich panel + 3 mm driver bit + insulation (outer wall), and gypsum board (inner wall) + 3 mm drivit (outer wall) were prepared for the sample. As result of the research for temperature characteristics, large temperature difference by each material was shown in $218^{\circ}C{\sim}995^{\circ}C$ at 30 seconds and $501^{\circ}C{\sim}1078^{\circ}C$ at 300 seconds. Especially when the inner wall was a plaster board, lowest temperature of $501^{\circ}C$ was shown at 300 seconds and marble inner wall showed the following lowest temperature of $900^{\circ}C$. Temperature rising over $1000^{\circ}C$ was shown in other materials. Regarding fire damage form, drivit or gypsum board outer wall parts exposed to fire showed combustion and carbonization to show calcination(breaking phenomenon) and influence of heat exposure was higher as calcination became more severe.

• Restorative Dentistry and Endodontics
• /
• v.46 no.1
• /
• pp.2.1-2.8
• /
• 2021

Objectives: New premixed bioceramic root repair materials require moisture for setting. Using micro-computed tomography (micro-CT), this study evaluated the filling ability and volumetric changes of calcium silicate-based repair materials (mineral trioxide aggregate repair high-plasticity [MTA HP] and Bio-C Repair, Angelus), in comparison with a zinc oxide and eugenol-based material (intermediate restorative material [IRM]; Dentsply DeTrey). Materials and Methods: Gypsum models with cavities 3 mm deep and 1 mm in diameter were manufactured and scanned using micro-CT (SkyScan 1272. Bruker). The cavities were filled with the cements and scanned again to evaluate their filling capacity. Another scan was performed after immersing the samples in distilled water for 7 days to assess the volumetric changes of the cements. The statistical significance of differences in the data was evaluated using analysis of variance and the Tukey test with a 5% significance level. Results: Bio-C Repair had a greater filling ability than MTA HP (p < 0.05). IRM was similar to Bio-C and MTA HP (p > 0.05). MTA HP presented the largest volumetric change (p < 0.05), showing more volume loss than Bio-C and IRM, which were similar (p > 0.05). Conclusions: Bio-C Repair is a new endodontic material with excellent filling capacity and low volumetric change. The gypsum model proposed for evaluating filling ability and volumetric changes by micro-CT had appropriate and reproducible results. This model may enhance the physicochemical evaluation of premixed bioceramic materials, which need moisture for setting.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.4
• /
• pp.481-487
• /
• 2017

The purpose of this study is to develop the hybrid sound-absorbing materials that is made from organic polyurethane sponge impregnated with inorganic binder solutions. The inorganic slurry which is made from ${\alpha}$-hemihydrate gypsum mixed with 60% water, and various additives including plasticizer are used as binder. The test specimens are prepared and tested for sound absorption performance by the impedance tube methods. From the test results, noise reduction coefficient(NRC) of development materials specimen bound by the inorganic binder slurry is 0.41. They are 2 times or more higher than commercial products specimens bound by organic materials only which have NRC values in the range of 0.14 to 0.28. The polyurethane sponge specimens impregnated with inorganic gypsum slurry binder have a good balance between performance and cost, and have proper properties in density, thermal conductivity, non-combustible, and absence of harmful substances as sound-absorbing internal boards for noise barrier wall. It is apparent that the good sound absorption materials can be produced according to the optimum mix design that is recommended from this study.

• Korean Journal of Soil Science and Fertilizer
• /
• v.40 no.2
• /
• pp.145-150
• /
• 2007

This study was conducted to evaluate the application effects of phospho-gypsum fertilizer (PGF) as reclamation material in the newly reclaimed paddy fields located in Goheung and Youngam, Jeonnam province in Korea. The PGF used in this experiment was produced by Namhae Chemical Co. as the name of Soil-Saver$^{TM}$. Prior to rice transplanting, the PGF was applied as soil amendment as the amount of $3,000kg\;ha^{-1}$. The PGF increases rice plant height and number of tiller at the heading stage by 119.9 cm and 9.1, respectively, in Youngam area. The harvest index of brown rice increased up to 5 and 13% more in the PGF applied paddy field from both sites than in the non-application of PGF at paddy field before rice transplanting, and the ripening ratio in increased in both sites to 81 and 90%. Protein content of brown rice was also greater than in the non-application of PGF at the both sites. For the effects of the reclamation by PGF in the paddy field soils, we found that PGF reduced exchangeable Na to 18 and 28% for both sites, respectively, and increased exchangeable Ca and $SO_4$. And we found relatively higher amounts of $K_2O$, CaO and MgO in the rice plants from both sites applied with PGF.