• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1383-1386
• /
• 1987

This paper concerns, the method for velocity of dynamic Image on two dimensional sequence Image which can be obtained from two sample lines on the street. The velocity of a single moving object Is measured by the number of total frame which Is required when an automobile passes over the second sample line through the first sample line. The measured results show that the velocity error Is less than 5% comparing with the value measured by X-band speed gun.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1200-1202
• /
• 2001

A programmable dymanometer is prosed where the user can define the steady-state and inertial torque-speed characteristic of the load. Rotating machinert can be tested on this dynamometer to determine their transient and steady-state characteristics with a pratical load. The system uses proportional-integrtal(PI)controllers to control a three-phase induction motor using indirect field orientation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.8
• /
• pp.713-718
• /
• 2002

Motion controllers are essential components for operating industrial equipments. Compared with general industrial controllers, motion controllers allow motion control requiring greater speed and precision. This paper presents a method for controlling multi-axes motors via industrial networks. To achieve a line or arc interpolation, the master system delivers instructions to slave systems connected to the network. The network instruction transmitted from the master controller is re-interpolated by the individual slaves through sub-interpolators. The re-interpolated feedrate information is transmitted to the motion control loop in which the current position and the reference position are then calculated. In this way, the interpolation driving between control units is achieved via industrial networks.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2748-2750
• /
• 1999

This Paper describes the design of an induction motor control using the TMS320C32 Digital Signal Processor and the ADMC201 motion coprocessor. Presented hardware architecture can be used for several industry applications with wide range of speed control, e.g. elevator and cranes application, servo motor, electrical vehicles. The main purpose of the paper is demonstration of the implementation and maximum utilization of the ADMC201 motion coprocessor in digital vector control system for AC drives.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.214-215
• /
• 2005

Naval equipments are installed and used for naval vessel with different environmental conditions comparing to the commercial vessel, for example, high engine power per ship displacement size, severe vibration and shock due to high running speed and explosion from naval gun's bombardment and underwater weapons. Therefore, those equipments must be installed on shipboard with small spaces, high ambient temperature around engine room and which are required be fabricated with high resistances of vibration, shock and heat resources. But in case of commercial vessel, the performances of their recent equipments naval have been improved continuously due to the technology development of domestic shipbuilding and shipboard equipment industries, together with the related fundamental industries i.e, metal, steel and electronic industries, to an international level since 1970. With these results, it became possible to unify the specifications of shipboard equipments for the commercial and military vessels(Dual-Use). In this study, vibration and shock test standards for the commercial and military vessels will be compared and reviewed technically.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.6
• /
• pp.384-390
• /
• 2015

The vibration analysis of rotating inward beams considering the pre-twisted is presented based on Euler-Bernoulli beam theory. The frequency equations, are calculated using hybrid deformation variable modeling along with the Rayleigh-Ritz assumed mode methods. In this study, resulting system of ordinary differential equations shows the effects of angular speed, and Young's modulus ratio. It is believed that the results will be a reference with which other researchers and commercial FE analysis program, ANSYS can compare their result.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.682-688
• /
• 2008

Transverse flux machine (TFM) has been considered as a promising driving machine especially at the low-speed applications because it has higher power density, torque and efficiency than the conventional electrical motors. However, it has complicated structure, large torque ripple and sometimes unbalanced magnetic force due to its inherent structure. This paper investigates the characteristics of torque ripple and unbalanced magnetic force of a rotatory two-phase TFM due to the teeth geometry by using the 3-dimensional finite element method, and it develops a rotatory two-phase TFM with herringbone teeth to reduce the torque ripple as well as to eliminate the unbalanced magnetic force.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.211-215
• /
• 2000

Bi-2212 HTS tube was fabricated by CFP(Centrifugal Forming Process). Slury was prepared in the mixing ratio of 8:2 between powder and binder and ball-milled for 24 hrs. Slurry was initially charged into the rotating mold with 300${\sim}$450 rpm and heated at the temperature ranges of 840${\sim}$860$^{\circ}$C for partial melting to finally obtain a uniformly textured tube shape. It was observed the plate-like grains with more than 20 ${\mu}$m were well oriented along the rotating axis and the measured T$_c$ was around 67K. In this paper we will discuss and analyze the tube characteristics depending on many different processing parameters such as, powder composition, binder mixing ratio between powder and binder, motor speed, heating temperature and etc.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1907-1909
• /
• 1996

In this paper, ultrsonic detection properties at a premolde joint utilized in a 23kV cables are studied. In a experiment a artificial defect within a joint and a measuring system are builded for generating discharges, gathering data about a detection properties, respectively. The experiment results show that one point detection is not allowed for monitoring a global status of a joint discharges and a detection sensitivity is less than 100pC. And also the attenuation and wave speed at the material of joint insulator are obtained.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1722-1723
• /
• 2008

This paper present dynamic stiffness of servo motor using labVIEW PXI module. In speed control loop, we apply proportional gain and integral gain, using PID controller, respectively in servo motor and confirmed dynamic stiffness of servo motor varing each gain. Changing proportional gain and integral gain, confirm what effect in dynamic stiffness are change in frequency response..