• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.19-22
• /
• 2005

As the optical communication industry is developed, the demand of optical communication part is increasing. $ZrO_2$ ceramic ferrule is very important part which can determines the transmission efficiency and information quality to connect the optical fibers. In general $ZrO_2$ ceramic ferrule is manufactured by grinding process because the demands precision is very high. And the co-axle grinding process of $ZrO_2$ ceramic ferrule is to make its concentricity all of uniform before centerless grinding. When co-axle grinding of ferrule supported by two pin, pin chucking alignment accuracy is very important. This paper deals with the analysis of the chucking alignment experiment with parallel error on the micro feeding equipment. Thus, if possible be finding highly good the chucking alignment of two pin.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.793-797
• /
• 2000

The environmental problems by using coolant demanded the new cooling methods. As one of them the studies on the dry grinding with compressed cold air have been done. The cooling method using compressed cold air was effdve thmugh going down the temperature of compressed air supplied below $-25^{\circ}C$ and inneasing the amount of mmpresd cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using MQL(Minimum Quantity Lubrication) or mist newly were suggested. These two methods can satisfy both cooling effect and lubrication with only small amount of coolant, also has the benefit in the point of decreasing the envimnmental pollution. This paper focused on analyzing the grindmg characteristics of the cooling method using mid. The generated heat and grinding force of the cooling method using mist were compared with them of coolant and compressed cold air. And them grinding test according to the temperature of compressed cold air, mist spray amount and mist supply direction were done.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.1
• /
• pp.149-156
• /
• 2017

Graphene nanoplatelet (GNP)-reinforced alumina ($Al_2O_3$) is a promising material for micro-partapplications, particularly micro-nozzle shapes, because of its excellent wearresistance. In this study, a $Al_2O_3$/GNPcomposite with 15 vol% graphene nanoplatelets (GNP) was highly densified and fabricated via spark plasma sintering for micro-electrical discharge drilling (Micro-ED drilling) and the wear resistance property of the composite is evaluated via the ball-on-disk method. In addition, the diameter and shape of the micro-electrodes machined by wire electrical discharge grinding (WEDG), block electrical discharge grinding (BEDG), and new linear block moving electrical discharge grinding (LBMEDG) methods are systematically compared and analyzed to observe the micro-hole machining in the micro-ED drilling of the $Al_2O_3$/15vol% GNP composite.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.3
• /
• pp.156-163
• /
• 2012

This research has been carried out to investigate the characteristics of cellulose nanofibers manufactured from domestic lignocellulosic materials by mechanical grinding method. The continuous grinding process was effective for loosening cell wall structure, with increasing grinding time, much smaller nanofibers were observed. Filtration time was linearly increased with increasing grinding time for all experimental materials. Relative crystallinity of cellulose was not changed by grinding process, but increased by delignification treatment. Tensile property of fiber sheets was drastically improved with increasing grinding time. Fibers sheets obtained from delignified cone stalks showed an excellent tensile strength. Consequently, it is considered that this study presented some effective information for manufacturing cellulose nanofibers with domestic plantation resources.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.70-73
• /
• 2002

Using zirconium ceramics makes the ferrule, which is the part of optical communications. The quality of optical communications is directly affected by the concentricity of the optic ferrule. The products of optic ferrule should be meet the following general conditions which are the outer diameter of 2.5mm and the inner diameter of 0.125mm, and high quality conditions which are the concentricity of 0.1~$0.3\mu\textrm{m}$, the form accuracy of $0.2\mu\textrm{m}$, the roundness and the cylindricity of $0.1\mu\textrm{m}$ and the surface roughness of 10nm. Generally, the diamond wheel is used for the high efficiency and precision grinding of the materials. It is good for keeping the shape as it has little wear. Because of the loading phenomena, however, it is difficult to keep the fresh surface of the wheel. In grinding process, grinding fragments resemble fine powders rather than chips. It can easily get attached to the wheel surface and thus cause a loading. The loading takes place, in which the impurities stick to the wheel surface, and the grinding characteristics of wheel is deteriorated. To prevent all of these, a suitable dressing method should be used for the wheel. In this research, the dressing system fur co-axial grinding machine was designed and produced for the machining of ferrule, which is a high performance part. The performance of the developed dressing system was evaluated by measuring the form accuracy of ferrule, which is machined by the dressed wheel in developed dressing system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.500-507
• /
• 2008

By Using various grinding mill in powder cosmetics manufacturing process; screen milt and pin mill, jet mill, properties of the powder and grinding mills were studied; talc, mica, nylon powder, silica, titanium dioxide. Besides, the experiments fur evaluation of grinding were performed by using iron oxides those are tracers. In powders of plate shape, they were grinded more vertically than horizontally at the screen mill and pin mill, although were all grinded vertically and horizontally at the jet mill. The spheric powders became the primary particles or aggregation by electrostatic interaction at the screen mill and pin mill. But, at the jet mill, they resulted the agglomeration or transformation or damage up to 2bar. Titanium dioxides became the primary particles by all grinding mill. Pin mill has an excellent result in experiments which is a change of the tone of color by grinding. From these results, suggest that the jet mill is used to pre-treat of powders of plate shape in practical cosmetic manufacturing process, and the screen mill and pin mill are used to match the color of powder cosmetics. If industrial process condition is taken into consideration, suggest that 4times of grinding is excellent on grinding effect by the screen mill, and twice grinding by the pin mill and grind air pressure of 1bar by the jet mill.

• Resources Recycling
• /
• v.28 no.3
• /
• pp.26-34
• /
• 2019

Due to the increasing demand of rare earth magnet for various application, it is predicted that the amount of waste rare earth magnet will increase sharply. The process of waste rare earth magnet recycling is mainly consisted of leaching and separation of rare earth element contained in the magnet. However, there is no study on the breakage characteristics of the waste rare earth magnet for production of magnet powder. Therefore, in this study, effective crushing/grinding process and breakage characteristics were investigated for waste rare earth magnet. In the case of jaw crusher, the particle size of magnet was effectively reduced without rapid oxidation. In ball mill grinding test, it was found that the grinding process was not performed properly at the early stage of grinding. Moreover, waste rare earth magnet showed very low specific rate of breakage(S) and high fraction of fine particle breakage distribution(B) compared to ordinary minerals. These results can be used as a basic data for developing crushing/grinding circuit of waste rare earth magnet.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.6
• /
• pp.701-708
• /
• 2011

Although Titanium material has superior properties, it belongs to difficult-to-machine materials. The present research applies magnetic abrasive finishing to precision machining of internal-face of titanium pipes, and analyzed & assessed the influence of grinding conditions on magnetic abrasive effects through the removed amount and surface roughness of materials. There was the influence on grinding properties according to change of rotational speed, a total input of mixed powder and an input of grinding liquid, and when the total input, rotational speed and ratio of electrolytic iron versus magnetic abrasives are 8g and 1000rpm, it was most advantageous in aspects of surface roughness and material removal amount, and the grinding liquid remarkably improved the surface roughness and material removal amount only with addition of trace amounts of light oil rather than dry machining conditions. And a result of considering the influence on grinding properties by using an inert gas (Argon gas) for improving grinding properties of the internal-face of titanium pipe, the present research has obtained improvement effects in the removal amount and surface roughness through utilization of an inert gas.

• Design & Manufacturing
• /
• v.1 no.1
• /
• pp.7-11
• /
• 2007

The fabrication of precision optical components by deterministic CNC grinding is an area of great current interest. Replacement of the traditional, craftsman driven, optical fabrication process is essential to reduce costs and increase process flexibility and reliability. Moreover, CNC grinding is well suited to the fabrication of complex shapes such as aspheres, making it possible to design optical systems with fewer components and reduced weight. Current technology is capable of producing surfaces with less than 2 microns peak to valley error, 50 nm rms surface roughness, and less than 1 micron subsurface damage. Bound abrasive tools, in which the abrasive particles are fixed in a second (matrix) material, play an important part in achieving this performance. In this paper, the factors affecting the ultra-fine surface roughness and profile accuracy of machined surfaces of aspheric parts has been analyzed experimentally and theoretically and on ultra-precision aspheric grinding system and precise adjusting mechanism have been designed and manufactured. In the paper we report the results of experiments and modeling performed to examine the effects of machinability, occurring during grinding of optical surfaces, on the tool surface profile. Profiles of machined surface were measured by using SEM. In order to optimize grinding conditions of aspheric lens processing, we performed experiments by design of experiments.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.685-691
• /
• 2013

Ibuprofen, non-steroidal anti-inflammatory drugs; NSAIDs, is a highly crystalline substance with the pharmaceutical properties of poor solubility and low bioavailability. The size reduction of ibuprofen is needed to improve the solubility. The objective of this study is to optimize the grinding condition of ibuprofen. Grinding of ibuprofen was carried out using a planetary mill. Grinding parameters were optimized using Box-Behnken experimental design method. The physical characteristics of ground ibuprofen were investigated for the particle size by particle size analyzer, for the crystal size by X-ray diffraction (XRD), and for the tensile strength by tensile/compression tester. The optimum conditions for the milling of ibuprofen were 290 rpm of the revolution number of mill, 24.6 g of the weight of sample, and 10 minutes of grinding time. The measured value of the particle size of ground ibuprofen at these optimum conditions was $13.5{\mu}m$. The results showed that the crystal size of ibuprofen was reduced by the planetary milling process. In case the relative density of the tablets formulated of ground ibuprofen was range of 0.85~0.90, the tensile strength of them was range of 1$2{\sim}14Kg_f/cm^2$.