한국정밀공학회지 (Journal of the Korean Society for Precision Engineering)

  • 제28권6호
  • /
  • Pages.701-708
  • /
  • 2011
  • /
  • 1225-9071(pISSN)
  • /
  • 2287-8769(eISSN)
한국정밀공학회 (Korean Society for Precision Engineering)
권호 표지

타이타늄 파이프의 내면 자기연마 가공에 관한 연구

A Study on the Characteristics of Internal-Face Magnetic Abrasive Finishing for Titanium Pipe

  • 이여해 (전북대학교 기계공학과) ;
  • 문상돈 (전북대학교 기계설계공학부) ;
  • 김영환 (전북대학교 기계설계공학부) ;
  • 박원기 (전북대학교 기계공학과) ;
  • 양균의 (전북대학교 기계공학과)
  • Li, Li-Hai (Department Mechanical Engineering, Chonbuk National Univ.) ;
  • Mun, Sang-Don (Faculty of Mechanical Design Engineering, Chonbuk National Univ.) ;
  • Kim, Young-Whan (Faculty of Mechanical Design Engineering, Chonbuk National Univ.) ;
  • Park, Won-Ki (Department Mechanical Engineering, Chonbuk National Univ.) ;
  • Yang, Gyun-Eui (Department Mechanical Engineering, Chonbuk National Univ.)
  • 투고 : 2010.09.20
  • 심사 : 2011.03.29
  • 발행 : 2011.06.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Although Titanium material has superior properties, it belongs to difficult-to-machine materials. The present research applies magnetic abrasive finishing to precision machining of internal-face of titanium pipes, and analyzed & assessed the influence of grinding conditions on magnetic abrasive effects through the removed amount and surface roughness of materials. There was the influence on grinding properties according to change of rotational speed, a total input of mixed powder and an input of grinding liquid, and when the total input, rotational speed and ratio of electrolytic iron versus magnetic abrasives are 8g and 1000rpm, it was most advantageous in aspects of surface roughness and material removal amount, and the grinding liquid remarkably improved the surface roughness and material removal amount only with addition of trace amounts of light oil rather than dry machining conditions. And a result of considering the influence on grinding properties by using an inert gas (Argon gas) for improving grinding properties of the internal-face of titanium pipe, the present research has obtained improvement effects in the removal amount and surface roughness through utilization of an inert gas.

키워드

참고문헌

  1. Lee, Y. T. and Hyun, Y. T., "Titanium parts for automobile," Journal of Korean Society of Automotive Engineers, Vol. 15, No. 4, pp. 8-13, 1993.
  2. Choi, J. G., Kim, H. S. and Chung, J. O., "Turning Characteristics of Various Tool Materials in the Machining of Ti-6Al-4V," Transactions of the Korean Society of Machine Tool Engineers, Vol. 17, No. 2, pp. 38-44, 2008.
  3. Kim, H. S., Choi, J. G., Kim, D. M. and Lyu, M. Y., "Machining Characteristics of Ti-6Al-4V Thread," Journal of the Korean Society of Machine Tool Engineers, Vol. 18, No. 5, pp. 514-520, 2009.
  4. Kim, N. Y., Ko, J. B. and Lee, D. J., "A Study on the Machining Characteristics of Ti-6Al-4V Alloy," Journal of the Korean Society of Precision Engineering, Vol. 20, No. 4, pp. 20-28, 2003.
  5. Hong, W. P., Kim, H. C. and Lee, D. J., "Machining Characteristics of Ti-6Al-4V Titainum Alloy," Proc. of the Korean Society of Precision Engineering Autumn Conference, pp. 818-822, 2000.
  6. Choi, B. M., Hong, S. K., Ryuh, B. S. and Park, S. M., "Development of PC-NC Water Jet Cutting System and Cutting of Titanium," Journal of the Korean Society for Precision Engineering, Vol. 18, No. 3, pp. 53-60, 2001.
  7. Kim, S. H., Lim, J. G., Ha, S. B., Choi, H. and Lee, J. C., "A Study on the Grinding of Titanium Alloy Part 1 : Grinding force, Specific grinding energy, Surface roughness, G-ratio," Proc. of the Korean Society of Precision Engineering Autumn Conference, pp. 870-874, 2000.
  8. Ha, G. H., Ku, S. J., Kang, M. C., Kim, J. S., Ha, J. H. and Yang, S. C., "Tool wear monitoring of end mill in slot machining of titanium alloy," Proc. of the Korean Society of Precision Engineering Autumn Conference, pp. 101-104, 1997.
  9. Kim, N. Y., Ko, J. B. and Lee, D. J., "A Study on the Tool Wear and Cutting Characteristics in the Machining of Ti-6Al-4V Using Tungsten Carbide Tool," Transactions of the Korean Society of Machine Tool Engineers, Vol. 11, No. 2, pp. 9-16, 2002.
  10. Heo, S., Kim, W. I., Wang, D. H. and Lee, Y. K., "Characteristics of Surface Grinding for Heat Treated Titanium Alloy," Proc. of the Korean Society of Machine Tool Engineers Autumn Conference, pp. 349-354, 2000.
  11. Kim, J. S., Park, G. B., Shin, O. C. and Jung, Y. G., "A Study on Superfinishing Characteristics of Titanium Using Polishing Film," Proc. of the Korean Society of Precision Engineering Autumn Conference, pp. 259-260, 2009.
  12. Mun, S. D., "Micro Machining of High-Hardness Materials Using Magnetic Abrasive Grains," International Journal of Precision Engineering and Manufacturing, Vol. 11, No. 5, pp. 763-770, 2010. https://doi.org/10.1007/s12541-010-0090-4
  13. Kim, T. W. and Kwak, J. S., "A Study on Deburring of Magnesium Alloy Plate by Magnetic Abrasive Polishing," International Journal of Precision Engineering and Manufacturing, Vol. 11, No. 2, pp. 189-194, 2010. https://doi.org/10.1007/s12541-010-0021-4
  14. Shinmura, T., Takazawa, K., Hatano, E. and Matsunaga, M., "Study on Magnetic Abrasive Finishing," Annals of the CIRP, Vol. 39, No. 1, pp. 325-328, 1990. https://doi.org/10.1016/S0007-8506(07)61064-6
  15. Shinmura, T. and Yamaguchi, H., "Precision Surface Finishing of Si3N4 Fine Ceramic Components by the Application of Magnetic Abrasive Machining Process," Journal of the JSME, Vol. 67, No. 12, pp. 1986-1990, 2001.
  16. Im, I. K., Mun, S. D. and Oh, S. M., "Micro Machining of an STS 304 Bar by Magnetic Abrasive Finishing," Journal of Mechanical Science and Technology, Vol. 23, No. 7, pp. 1982-1988, 2009. https://doi.org/10.1007/s12206-009-0524-z
  17. Maiboroda, V. S., Stepanov, O. V., Taranenko, N. L. and Vermenko, V. Y., "Rheological Characteristics of Magnetic-Abrasive Powders in a Magnetic Field," Powder Metallurgy and Metal Ceramics, Vol. 33, No. 1-2, pp. 57-60, 1994.