• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.425-431
• /
• 1999

Nowadays development of electric and optical devices needs precision more and more. This study focuses on hydrostatic journal bearing of grinding wheel spindle. It presents theoretical analysis about cylinder type self-controlled restrictor to control flux of oil flowing into pockets around the hydrostatic journal bearing. As a result of this analysis, optimal properties to maximize bearing stiffness such as initial cross distance, supply pressure, diameter of two supply holes, pre-load of spring and clearance between spindle and housing can be obtained. Therefore, by using them it is possible to estimate bearing stiffness and the performance of grinding wheel spindle can be improved.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.3
• /
• pp.105-110
• /
• 2020

Alumina, a typical ceramic material used for semiconductors and display parts, is the subject of research and development efforts for mineral material processing. Alumina is extremely difficult to process since it is brittleness to either fine ceramics material. We have studied the shape of diamond particles and their use in machinability for alumina processing. Our study was carried out under various processing conditions, including cutting speed, table speed, and the surface roughness of the work piece. We also analyzed the wear characteristics of the tool by total cutting.

• Journal of Welding and Joining
• /
• v.26 no.4
• /
• pp.55-60
• /
• 2008

Structural reliability of electrical panels installed in naval vessels is of critical importance from structural performance viewpoint. The panels may be exposed to vibration and fatigue loadings from internal and external sources and wave loading which cause fatigue cracking. In this study, common methods such as burr grinding and post weld heat treatment (PWHT), for the fatigue strength improvement of weldments are investigated. Burr grinding is carried out using a electric grinder in order to remove surface defects and improve the weld bead profile. And also PWHT is carried out for the purpose of removing residual. The effectiveness of the two post treatment methods is evaluated in terms of fatigue strength improvement of welded structures.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.6
• /
• pp.681-689
• /
• 2009

Disk grinding was often applied to deburring process in order to enhance the final product quality. Inherent chamfering capability of the flexible disk grinding process in the early stage was analyzed with respect to various process parameters including workpiece length, wheel speed, depth of cut and feed. Initial chamfered edge defined as arc zone was characterized with local radius of curvature. Averaged radius and arc zone ratio was well evaluated using neural network system. Additional neural network analysis adding workpiece length showed enhance performance in predicting arc zone ratio and curvature radius with reduced error rate. A process condition design parameter was estimated using remaining input and output parameters with the prediction error rate lower than 2.0% depending on the relevant input parameter combination and neural network structure composition.

• Journal of Korean Institute of Industrial Engineers
• /
• v.26 no.4
• /
• pp.376-383
• /
• 2000

A flexible disk grinding process model has been implemented with varying disk orientation with respect to workpiece surface along with variable feed rate. Before implementing arbitrary disk orientation and translation, disk angle and feed rate variation have been implemented. The disk angle was changed with constant angular velocity only in the entrance stage. The effect of the variable feed rate was added to the geometric schematic. The feed rate was changed either from the entrance stage or from the between edges stage and process performance was evaluated. Effect of changing both angle end feed rate has been also analyzed. Disk trend showing actual disk deflection has also been visualized.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.122-123
• /
• 2021

This study examines the performance of pretreatment process system as the initial construction stage of the pretreatment process system to use CGS, a by-product generated in IGCC, as a concrete fine aggregate of construction materials. The process undergoes a grinding process capable of grinding to a predetermined particle size during primary grinding and a sorting plant through sieve grading of 2.5 mm or less for particle size correction. Afterwards, it is hoped that the use of coal gasification slag of Korean IGCC as a fine aggregate for concrete will be distributed and expanded by producing quality-improved CGS fine aggregate using water as a medium for removing impurities and particulates.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.254-257
• /
• 2002

As the large Coolant amount used of a machine holds mass serious trouble recently, an environment pollution is increased, and a machine is conquering large specific gravity in an empty cost plane. It is the stage that must reexamine the parts washing that processing is later with this current way or a problem of a liquid waste treatment back. The environmental problems by using coolant demanded the new cooling methods. As one of them, the studies on the grinding with compressed cold air and oil mist have been done. The cooling method using compressed cold air was effective through going down the temperature of compressed air supplied below -$25^{\circ}C$ and increasing the amount of compressed cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using oil mist newly were suggested. This method can satisfy both cooling effect and lubrication with only small amount of coolant, also have the benefit in the point of decreasing the environmental pollution. This paper focused on analyzing the grinding characteristics of the cooling method using oil mist. The grinding test according to compressed cold air and oil mist supply direction were done.

• Advances in nano research
• /
• v.12 no.6
• /
• pp.583-592
• /
• 2022

In this paper, a pulsed picosecond laser dressing method for bronze-bonded diamond wheel is studied systematically and comprehensively. The picosecond laser pulse ablation experiment is carried out, and the ablation thresholds of bronze-bonded and diamond abrasive particle are measured respectively. The results indicate that the single-pulse ablation thresholds of bronze-bonded are 0.89J/cm², 0.24J/cm² during strong/weak ablation stages. And the multi-pulse ablation thresholds of diamond abrasive particle are 1.69J/cm², 0.49J/cm² during strong/weak ablation stages. Obviously, diamond grains have less thermal damage during the process of gentle ablation. The diamond grains of the grinding wheel surface are graphitized during laser dressing. The bronze-bonded is relatively smooth and organizational stability, and the diamond grits have suitable prominent height, which are beneficial to maintain the good grinding performance of dressed bronze-bonded diamond grinding wheels.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1119-1120
• /
• 2006

High Energy Milling (HEM) is applied for the grinding of cement and this can lead to substantial refinement $(<2{\mu}m)$ and mechanically activation of the powder particles. The present paper reviews the preliminary studies, explains the novel technique and suggests the route into commercial application. Particular attention is paid to wear results with an applied $Si_3N_4-grinding$ unit where no substantial wear was found after 4000 h of operation.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.12
• /
• pp.1285-1289
• /
• 2012

This study has been focused on application of ELID lapping process for mirror-surface machining of sapphire wafer. Sapphire wafer is a superior material with optic properties of high performance as light transmission, thermal conductivity, hardness and so on. High effective surface machining technology is necessary to use sapphire as various usages. The interval ELID lapping process has been set up for lapping of the sapphire material. According to the ELID lapping experimental results, it shows that 12.5 kg of load for lapping is most pertinent to ELID lapping. the surface of sapphire can be eliminated by metal bonded wheel with micron abrasives and the surface roughness of 60 nmRa can be gotten using grinding wheel of 2,000 mesh in 4.5 um, depth of cut. In this study, the chemical experiments after ELID grinding also has been conducted to check chemical reaction between workpiece and grinding wheel on ELID grinding process. It shows that the chemical reaction has not happened as the results of the chemical experiments.