• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.5
• /
• pp.9-15
• /
• 2022

Discarded bio-wastes, such as seeds and rinds, cause environmental problems. Multiple studies have recycled bio-wastes as eco-friendly energy sources to solve these problems. This study uses bio-waste to fabricate a mandarin peel powder based triboelectric nanogenerator (MPP-TENG). The MPP-TENG is based on the contact separation mode. It generates an open-circuit voltage and short-circuit current of 156V and 2µA, respectively. In addition, MPP-TENG shows stable operation over continuous 3000s without any deviation in output. Also, the device exhibits maximum power density of 5.3㎼/cm² when connected to a resistance of 100MΩ. In an energy storage capacity test for 1000s, the MPP-TENG stores an energy of 171.6µJ in a 4.7µF capacitor. The MPP-TENG can power 9 blue LEDs and 54 green lettering LEDs. These results confirm that the MPP-TENG can provide a new avenue for eco-friendly energy harvesting device fabrication.

• Journal of Bio-Environment Control
• /
• v.28 no.4
• /
• pp.404-410
• /
• 2019

This study was performed to investigate the seed morphological characteristics and dormancy type of Adenophora triphylla var. japonica Hara that high valued medicinal crop and to select the disinfectants and light quality for germination rate improvement. The seed disinfection was carried out using distilled water (control), NaClO 4%, $H_2O_2$ 4%, and benomyl $500mg{\cdot}L^{-1}$. The light quality treatments were set to dark condition (control I), fluorescent lamp (control II), LEDs [red, blue, green, and combined RB LEDs (red:blue = 8:2, 6:4, 4:6, 2:8)] with a photoperiod of 12/12 (light/dark) and light intensity $150{\pm}10{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ photosynthetic photon flux density. Although the Adenophora triphylla var. japonica Hara seed was an underdeveloped embryo (E) and seed (S) with an embryo (E):seed (S) ratio of 0.4, it is germinated within 30 days, and seed moisture saturation was reached within 6 hours after immersion. After seed disinfection, the mold incidence rate was significantly inhibited, and the final germination rate was the highest at 87% in the benomyl seed disinfection. The final germination rate was the highest at 92% in the red light, and the mean daily germination was the lowest in the R2B8. Therefore, there is almost no dormancy in the Adenophora triphylla var. japonica Hara seed, and benomyl seed disinfectant and red light were effective in the improvement of germination rate. So it is considered to the high value of use for medicinal crop Adenophora triphylla var. japonica Hara cultivation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.2
• /
• pp.10-18
• /
• 2011

In order to develop highly-integrated RGBY(Red, Green, Blue, Yellow) LED light, a high thermal radiation ceramic package was manufactured, and the encapsulation process was applied with a vacuum printing encapsulation system(VPES). After the completion of vacuum printing, the shape of the encapsulation layer could be controlled by heat treatment during the curing process, and the optical power became highly increased as the encapsulation layer approached a dome shape. The optical characteristics involved in a Correlated Color Temperature(CCT), a Color Rendering Index (CRI), and the efficiency of RGBY LED light were able to be identified by the experimental designing method. Regarding the characteristics of the white light of RGBY LED light, which were measured on the basis of the aforementioned optical characteristics, CRI posted 88, CCT recorded 5,720[$^{\circ}K$], and efficiency exhibited 52[lm/W]. The chip temperature of RGBY LEDs was below 55[$^{\circ}C$] when the consumption power of LED chips was 0.1[W] for the red, 0.3[W] for the green, 0.08[W] for the blue, and 0.24[W] for the yellow. Also, the thermal resistance of the highly-integrated RGBY LED light measured by T3Ster was 2.3[K/W].

• Journal of the Korean institute of surface engineering
• /
• v.48 no.5
• /
• pp.211-217
• /
• 2015

To fabricate white LED having a high color rendering index value, red color phosphor mixed with the green color phosphor together in the blue chip, namely the blue chips with RG phosphors packaging is most favorable for high power white LEDs. In our previous papers, we reported on successful syntheses of $Sr_{2-}$ $Si_5N_8:Eu^{2+}$ and $CaAlSiN_3$ phosphors for red phosphor. In this work, for high power green phosphor, greenemitting ternary nitride $Ba_3Si_6O_{12}N_2:Eu^{2+}$ phosphor was synthesized in a high frequency induction furnace under $N_2$ gas atmosphere at temperatures up to $1400^{\circ}C$ using $EuF_3$ as a raw material for $Eu^{2+}$ dopant. The effects of molar ratio of component and experimental conditions on luminescence property of prepared phosphors have been investigated. The structure and luminescence properties of prepared $Ba_3Si_6O_{12}N_2:Eu^{2+}$ phosphors were investigated by XRD and photoluminescence spectroscopy. The excitation spectra of $Ba_3Si_6O_{12}N_2:Eu^{2+}$ phosphors indicated broad excitation wavelength range of 250 - 500 nm, namely from UV to blue region with distinct enhanced emission spectrum peaking at ${\approx}530nm$.

• Journal of Bio-Environment Control
• /
• v.29 no.2
• /
• pp.171-180
• /
• 2020

The effect of three different light qualities on growth, photosynthesis, quality and safe parameters of hydroponic cultivated spinach (Spinacia oleracea L.) were investigated indoor. Three different light qualities were created of red (660 nm), blue (450 nm) and green (550 nm) LEDs corresponding at ratio R660/B450 = 4/1 (RBL); R660/B450/G550= 5/2/3 (WWL); R660/B450/G550 = 1/1/1 (WL), which were tested at the same intensity (PPFD =190 μmol m^-2 s^-1). The results showed that the plant height and leaf number were the lowest in WL treatment. The SPAD, Net photosynthesis rate Pn, Fv/Fm, Leaf area index LAI values and all parameters of root characteristics were the highest in RBL treatment and were significantly different from two others. Fresh weight of stem, leaf and root, dry weight of root in the three light qualities were significantly different. In contrast, the highest K⁺ content in WL was different from WWL and RBL treatments, while Ca²⁺ and Fe²⁺ content were the highest in the RBL treatment. Vitamin C content was significantly different between the three treatments. nitrate and oxalic acid contents were the highest in WL treatment, whereas soluble-solids contents and vitamin C contents were the highest in RBL treatment. Oxalic acid, nitrate contents were observed tending reduced under WWL although oxalic acid content in RBL treatment was not different from WL and WWL treatments. In all three different light treatments were not detected Salmonella, E.coli. Our results suggest that RBL may be appropriate light for growth of spinach, but supplementary green light to a combination of red and blue LEDs at the reasonable rate can change the quality of spinach in a positive direction. Hydroponic cultivated spinach was safe for users.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.339-345
• /
• 2018

We investigated the curing properties of cured coatings for a multi-focal UV-LED. The coatings are for LEDs that operate at multiple UV wavelengths, unlike conventional single-wavelength UV-LEDs. Using UV-LED light sources with wavelengths of 365, 395, 420, and 450 nm, we analyzed the optical characteristics such as the direction of light flux and light source. We also analyzed the curing characteristics at each UV-LED wavelength to optimize the LED for composite wavelengths. The curing performance state was predicted through computer simulation for when the multiple wavelengths of UV light sources are superimposed, and then actual LEDs were designed and fabricated. To improve the internal high-speed curing, a multi-spot module was fabricated, in which each LED is condensed, and multiple wavelengths are synthesized and condensed at the same position. The adhesive strength, surface hardness, and internal hardness of the curing agent were tested by varying the wavelength combination conditions. The surface hardening and internal hardening were compared and analyzed using a hardness tester and FT-IR analyzer. As a result, the characteristics of the surface and internal hardness were improved by a multi-spot method in which four wavelengths were overlapped in a UV-LED rather than a single wavelength.

• Journal of Bio-Environment Control
• /
• v.25 no.3
• /
• pp.139-145
• /
• 2016

The objective of this study was to compare the growth and light use efficiency of red leaf lettuce grown under three types of combined light-emitting diodes (LEDs) and fluorescent lamps (FL) in a closed-type plant production system. The eighteen days-old lettuce seedlings of red leaf lettuce (Lactuca sativa L., 'Jeokchima') were transplanted to the close-type plant production system equipped with three types of combined LEDs with red (R, 655 nm), blue (B, 456 nm), green (G, 515 nm), and white (W, 456 nm + 558 nm) (R:B=8:2, R:W:B=8:1:1, R:G:B=8:1:1) and FL. The seedlings were grown under normal growth conditions ($20^{\circ}C$, $181{\pm}4{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, 12 h photoperiod) for four weeks. Lettuce plants grown under FL had significantly higher leaf shape index than those under all LED treatments. Although growth of shoots and roots was not show any significant difference among LED treatments, all of the LED treatments induced about 34% higher shoot fresh weight than that of the FL. On the other hands, the total power consumption of FL was 145 kW for 4 weeks, while the mean value of LED treatments was 54 kW, which was about 3 times lower value than that of the FL. The light use efficiency based on dry matter in LED treatments was about 34 mg/W and this was about 3.5 times higher energy saving value than the FL. In conclusion, this study showed that irradiation of optimal combined LEDs in closed-type plant production systems can improve the lettuce growth as well as maximize in light use efficiency through energy saving than the FL.

• Economic and Environmental Geology
• /
• v.50 no.3
• /
• pp.251-256
• /
• 2017

This study presents measures to enhance the efficiency of Successive Alkalinity Producing Systems(SAPS), a natural biological purification method that prevents environmental pollution arising from the release of Acid Mine Drainage(AMD) from abandoned mines into rivers and groundwater. The treatment of AMD using SAPS is based on biological processing technology that mostly involves sulfate reducing bacteria(SRB). It has been proven effective in real-world applications, and has been employed in various projects on the purification of AMD. However, seasonal decrease in temperature leads to a deterioration in the efficiency of the process because sulfate-reducing activity is almost non-existent during cold winters and early spring even if SRB is able to survive. Against this backdrop, this study presents measures to enhance the activity of the SRB of the organic layer by integrating light emitting diode(LED)s in SAPS and to maintain the active temperature using LEDs in cold winters. Given that mine drainage facilities are located in areas where power cannot be easily supplied, solar cell modules are proposed as the main power source for LEDs. By conducting further research based on the present study, it will be possible to enhance the efficiency of AMD treatment under extreme cold weather using solar energy and LEDs, which will serve as an environmentally-friendly solution in line with the era of green growth.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.7
• /
• pp.1044-1049
• /
• 2014

This study was conducted in order to investigate whether the presence of light or different colors of light would influence the energy expenditure and behavior of broiler chickens. Eight 8-week-old broiler chickens were adapted to a respiration chamber (Length, 28.5 cm; Height, 38.5 cm; Width, 44.0 cm) for one week prior to the initiation of the experiment. In experiment 1, energy expenditure and behavior of the chickens were analyzed in the presence or absence of light for four days. Chickens were exposed to 6 cycles of 2 h light/2 h dark period per day. In experiment 2, the broiler chickens that had been used in experiment 1 were used to evaluate the effect of 4 different wavelength light-emitting diodes (LEDs) on the energy expenditure and behavior of broiler chickens. The LEDs used in this study had the following wavelength bands; white (control), red (618 to 635 nm), green (515 to 530 nm) and blue (450 to 470 nm). The chickens were randomly exposed to a 2-h LED light in a random and sequential order per day for 3 days. Oxygen consumption and carbon dioxide production of the chickens were recorded using an open-circuit calorimeter system, and energy expenditure was calculated based on the collected data. The behavior of the chickens was analyzed based on following categories i.e., resting, standing, and pecking, and closed-circuit television was used to record these behavioral postures. The analysis of data from experiment 1 showed that the energy expenditure was higher (p<0.001) in chickens under light condition compared with those under dark condition. The chickens spent more time with pecking during a light period, but they frequently exhibited resting during a dark period. Experiment 2 showed that there was no significant difference in terms of energy expenditure and behavior based on the color of light (white, red, green, and blue) to which the chickens were exposed. In conclusion, the energy expenditure and behavior of broiler chickens were found to be strongly affected by the presence of light. On the other hand, there was no discernible difference in their energy expenditure and behavior of broiler chickens exposed to the different LED lights.

• Korean Journal of Optics and Photonics
• /
• v.32 no.5
• /
• pp.235-243
• /
• 2021

Photobiomodulation (PBM)-based therapy, which uses a phenomenon in which a light source of a specific wavelength band promotes ATP production in mitochondria, has attracted much attention in the fields of biology and medicine because of its effects on wound healing, inflammation reduction, and pain relief. Research on PBM-based therapy has mainly used lasers and light-emitting diodes (LEDs) as light sources and, despite the advantages of organic light-emitting diodes (OLEDs), there have been only a few cases where OLEDs were used in PBM-based therapy. In this research, the skin-care effect of PBM was analyzed using red (λ = 620 nm), green (λ = 525 nm), and blue (λ = 455 nm) OLED lighting modules, and was compared to the PBM effect of LEDs. We demonstrated the PBM-based skin-care effect of the red, green, blue OLED lighting modules by measuring the increase in the amount of collagen type-1 synthesis, the inhibition of melanin synthesis, and the suppression of nitric oxide generation, respectively.