• Structural Engineering and Mechanics
• /
• v.77 no.2
• /
• pp.261-272
• /
• 2021

The energy-saving block and invisible multi-ribbed frame composite wall (EBIMFCW) is a new type of load-bearing wall. The study of this paper focus on it is hysteresis rule under horizontal cyclic loading. Firstly, based on the experimental data of the twelve specimens under horizontal cyclic loading, the influence of two important parameters of axial compression ratio and shear-span ratio on the restoring force model was analyzed. Secondly, a tetra-linear restoring force model considering four feature points and the degradation law of unloading stiffness was established by combining theoretical analysis and regression analysis of experimental data, and the theoretical formula of the peak load of the EBIMFCW was derived. Finally, the hysteretic path of the restoring force model was determined by analyzing the hysteresis characteristics of the typical hysteresis loop. The results show that the curves calculated by the tetra-linear restoring force model in this paper agree well with the experimental curves, especially the calculated values of the peak load of the wall are very close to the experimental values, which can provide a reference for the elastic-plastic analysis of the EBIMFCW.

• Journal of Sensor Science and Technology
• /
• v.31 no.4
• /
• pp.218-227
• /
• 2022

Triboelectric nanogenerators (TENGs), a new green energy, that have various potential applications, such as energy harvesters and self-powered sensors. The output performance of TENGs has been improving rapidly, and their output power significantly increased since they were first reported owing to improved triboelectrification materials and interfacial material engineering. Because the operation of a TENG is based on contact electrification in which electric charges are exchanged at the interface between two materials, its output can be increased by increasing the contact area and charge density. Material surface modification with microstructures or nanostructures has increased the output performance of TENGs significantly because not only does the sharp micro/nano morphology increases the contact area during friction, but it also increases the charge density. Chemical treatment in which ions or functional groups are added has also been used to improve the performance of TENGS by modifying the work functions, charge densities, and dielectric constants of the triboelectric materials. In addition, ultrahigh output power from TENGs without using new materials or treatments has been obtained in many studies in which special structures were designed to control the current release or to collect the charge current directly. In this review, we discuss physical and chemical treatments, bulk modifications, and interfacial engineering for enhancing TENG performance by improving contact electrification and electrostatic induction.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.6
• /
• pp.616-622
• /
• 2022

At the present time, interest in hydrogen is increasingly growing worldwide to tackle climate change. Korea also takes an action by announcing the first hydrogen economy implementation basic plan with the import targets of 22.9 million tons of hydrogen from oversea in 2050. To achieve this plan, it is very essential to establish an overseas hydrogen supply chain. In this paper, the study estimates the import price for hydrogen into basic scenario and comprehensive scenario, and also analyses economic feasibility considering price of the each technology.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.6
• /
• pp.594-600
• /
• 2023

In this study, a process model and optimization design direction for a hydrogen production plant through ammonia decomposition are presented. If the reactor decomposition rate is designed to approach 100%, the amount of catalyst increases and the devices that make up the entire system also have a large design capacity. However, if the characteristics of the hydrogen regeneration process are reflected in the design of the reactor, it becomes possible to satisfy the total flow rate of fuel gas with the discharged tail gas flow rate. Analyzing the plant process simulation results, it was confirmed that when an appropriate decomposition rate is maintained in the reactor, the phenomenon of excess or shortage of fuel gas disappears. In addition, it became possible to reduce the amount of catalyst required and design the optimized capacity of the relevant processes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.518-527
• /
• 2020

The establishment of a green remodeling strategy is focused on technology, so the necessity of establishing a customized strategy considering the field situation has emerged. This paper examined the technology strategy through sensitivity analysis as a methodology for guiding strategy. For a 90-square-meter detached house, nine models of the construction standards of pre-1980s, 1984, and 2010 in Seoul, Daejeon, and Busan were assessed using the optimization method that combines the energy plus engine and the ModeFrontier. Sensitivity analysis was performed, and the remodeling strategy priority was derived. For pre-1980 models, the strategy for enhancing the roof insulation performance had a significant priority. The SHGC values of the windows were found to have the next highest priority regardless of the region and the time of completion, showing that the performance standard, including the SHGC, needs to be expanded. The possibility of remodeling while maintaining the existing geometry was confirmed because the adjustment of the window wall ratio accompanying large-scale demolition works has low priority. The priorities of technology strategies in each case showed very different patterns, suggesting the possibility of establishing a remodeling strategy by a comprehensive evaluation along with economics and constructability analysis.

• Corrosion Science and Technology
• /
• v.10 no.4
• /
• pp.109-117
• /
• 2011

The Korean Peninsula is located in the middle latitude of the northern hemisphere and has a clear 4-seasons and shows the typical temperate climate. Because of seasonal winds, it is cold and dry by a northwestern wind in the winter and it is hot and humid by a southeast wind in the summer. Also, temperature difference between the winter and the summer is large and it shows a rainy season from June to July but recently this regular trend may be greatly changed by an unusual weather phenomena. Since the Peninsula is east high west low type, the climate is complicated too. Because these geographical and climate characteristics can affect the properties of corrosion of metals and alloys, a systematic research on atmospheric corrosion in the Peninsula is required to understand and control the corrosion behavior of the industrial facilities. This paper analyzed the atmospheric corrosion factors for several environments in the Korean Peninsula and categorized the corrosivity of atmospheric corrosion of metals and alloys on the base of the related ISO standards. Annual pH values of rain showed the range of 4.5~5.5 in Korean Peninsula from 1999 to 2009 and coastal area showed relatively the low pH's rain. Annual $SO_2$ concentrations is reduced with time and its concentrations of every major cities were below the air quality standard, but $NO_2$concentration revealed a steady state and its concentration of Seoul has been over air quality standard. In 2007, $SO_2$classes of each sites were in $P_0{\sim}P_1$, and chloride classes were in $S_0{\sim}S_1$, and TOW classes were in ${\tau}_3{\sim}{\tau}_4$.That is, $SO_2$ and chloride classes were low but TOW class was high in Korean Peninsula. On the base of these environmental classes, corrosivity of carbon steel, zinc, copper, aluminium can be calculated that carbon steel was in C2-C3 classes and it was classified as low-medium, and zinc, copper, and aluminium showed C3 class and it was classified as medium.

• Korean Chemical Engineering Research
• /
• v.62 no.1
• /
• pp.36-43
• /
• 2024

Fishing net waste (FNW) constitutes over half of all marine plastic waste and is a major contributor to the degradation of marine ecosystems. While current treatment options for FNW include incineration, landfilling, and mechanical recycling, these methods often result in low-value products and pollutant emissions. Importantly, FNWs, comprised of plastic polymers, can be converted into valuable resources like syngas and pyrolysis oil through pyrolysis. Thus, this study presents a process for generating high-purity hydrogen (H₂) by catalytically pyrolyzing FNW in a CO₂ environment. The proposed process comprises of three stages: First, the pretreated FNW undergoes Ni/SiO₂ catalytic pyrolysis under CO₂ conditions to produce syngas and pyrolysis oil. Second, the produced pyrolysis oil is incinerated and repurposed as an energy source for the pyrolysis reaction. Lastly, the syngas is transformed into high-purity H₂ via the Water-Gas-Shift (WGS) reaction and Pressure Swing Adsorption (PSA). This study compares the results of the proposed process with those of traditional pyrolysis conducted under N₂ conditions. Simulation results show that pyrolyzing 500 kg/h of FNW produced 2.933 kmol/h of high-purity H₂ under N₂ conditions and 3.605 kmol/h of high-purity H₂ under CO₂ conditions. Furthermore, pyrolysis under CO₂ conditions improved CO production, increasing H₂ output. Additionally, the CO₂ emissions were reduced by 89.8% compared to N₂ conditions due to the capture and utilization of CO₂ released during the process. Therefore, the proposed process under CO₂ conditions can efficiently recycle FNW and generate eco-friendly hydrogen product.

• Journal of the Korean Ceramic Society
• /
• v.45 no.11
• /
• pp.701-706
• /
• 2008

High frequency dielectric ceramics have potential for applications in mobile and satellite communications systems at frequencies higher than 10GHz. The Ba$(Zn_{1/3}Ta_{2/3})O_3$ ceramics are known to have a high quality factor, a small temperature coefficient of the resonance frequency and a high dielectric constant. On the other hands, sintering at high temperature for extended time is required to obtain the ordered structure for high quality factor. In this study, the microwave dielectric properties of $ZrO_2$ and NiO-added Ba$(Zn_{1/3}Ta_{2/3})O_3$ ceramics prepared by solid-state reaction have been investigated. Adding $ZrO_2$ and NiO could effectively promote the densification even the case of decreasing the sintering time. At the surface of samples, secondary phase of Ba-Ta compounds was formed possibly due to the evaporation of ZnO, however, the interior of the samples remained as pure Ba$(Zn_{1/3}Ta_{2/3})O_3$. The samples sintered at $1600^{\circ}C$ for 2h exhibited 1:2 ordering of Zn and Ta cations. Excellent microwave dielectric properties of $Q{\cdot}f$(>96,000 GHz) and ${\varepsilon}_r$=30 has been obtained.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.2
• /
• pp.93-97
• /
• 2012

In this study, the fabrication and the characteristic analyses of OLED using in-situ passivation are investigated. OLEDs represent a disadvantage in decreasing its life due to the degradation caused by the penetration of moisture and oxygen. After the fabrication of OLED, an in-situ passivation method for inorganic thin films is developed. A process that uses PECVD method which can apply a vapor deposition process at room temperature is also developed. Changes in the degradation and electric characteristics of OLEDs are also analyzed by applying $SiO_2$ and SiNx thin films to OLED as a passivation layer. By applying the fabricated thin film to OLEDs as a passivation layer, the moisture penetration in a single layer film is ensured below $1{\times}10^{-2}\;g/m^2.day$. This leads to the improvement of such degradation characteristics in the application of multilayer films.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.3
• /
• pp.378-386
• /
• 2012

For reduction of the amount of CO2 emitted from ships, power generation characteristics of two power generation systems consisting of a high-efficiency permanent magnet synchronous generator and diode bridge rictifiers are discussed in this paper. One of the discussed systems has three-phase stator windings, and the other has two sets of three-phase (six-phase) stator windings to reduce pulsation in the electromagnetic torque and DC current. Experimental results reveal that the power generation efficiency of the system having six-phase stator windings is higher than that of the system having three-phase stator windings for a light load. The maximum power generation efficiency of the system having six-phase stator windings is almost the same as that of the system having three-phase stator windings. For the electromagnetic torque of the system having six-phase stator windings, the width of pulsation is about one-fifth compared to the system having three-phase stator windings.