• Food Science and Preservation
• /
• v.11 no.2
• /
• pp.269-275
• /
• 2004

This study was conducted to develop an optimization model using Box's Complex Algorithm, and to determine optimum operating conditions to minimize costs for the drying and storage system using the grain cooler. To minimize the system operation cost, the optimum moisture contents after the first drying were found to be from 17.2 to 19.8 %. And optimum drying and cooling capacities were obtained. The combination of the dryer and grain cooler was found to be economical, showing enhancement of the drying capacity over 50%, and decrease of drying cost over 10%. When the circulating grain dryers of 6 and 20 ton/batch were used in conjunction with the grain cooler, the cost required for drying and storage system for paddy were 28,464∼33,317won/ton and 20,588∼26,511 won/ton, respectively, which was from 2.6 to 27.3% lower than that of conventional drying and storage system.

• Journal of the Korean Ceramic Society
• /
• v.36 no.6
• /
• pp.646-654
• /
• 1999

• Korean Journal of Metals and Materials
• /
• v.49 no.11
• /
• pp.893-899
• /
• 2011

Fabrication of a complex aluminum alloy by the ARB process using dissimilar aluminum alloys has been carried out. Two-layer stack ARB was performed for up to six cycles at ambient temperature without a lubricant according to the conventional procedure. Dissimilar aluminum sheets of AA1050 and AA5052 with thickness of 1 mm were degreased and wire-brushed for the ARB process. The sheets were then stacked together and rolled to 50% reduction such that the thickness became 1 mm again. The sheet was then cut into two pieces of identical length and the same procedure was repeated for up to six cycles. A sound complex aluminum alloy sheet was successfully fabricated by the ARB process. The tensile strength increased as the number of ARB cycles was increased, reaching 298 MPa after 5 cycles, which is about 2.2 times that of the initial material. The average grain size was $24{\mu}m$ after 1 cycle, and became $1.8{\mu}m$ after 6 cycles.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.4
• /
• pp.127-133
• /
• 2008

As the application of the MEMS parts increases, the structural safety of MEMS appears importantly. A lot of MEMS parts are made by a multi-grain silicon wafer, which is an orthotropic material. Moreover directions of the materials on each grain are distributed randomly. The stress analysis for the multi-grain is important factor in order to apply the MEMS parts to industrial applications. The finite element method (FEM) is commonly used by a stress analysis method but the boundary element method (BEM) is known as the result of the BEM is more accurate than that of the FEM since the fundamental solution are used. In this study, we derived the boundary integration equation for the orthotropic material by applying fundamental solutions with complex variables. The multi-region analysis procedure for the BEM and the multi-grain generation procedure by a random process technique are developed in order to apply the analysis of the multi-grain orthotropic material. The discontinuous element is used in order to remove the comer problem in the BEM. The results of the present method are compared with those of the finite element method in order to verify the present procedure.

• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.55-61
• /
• 2000

The sintering characteristics of PVA-Al(III) complex added $UO_2$ pellet and AlOOH added $UO_2$pellet were compared. The major phase of PVA-Al(III) complex and AlOOH decomposed at $1000^{\circ}C$ in $H_2$atmosphere was $\theta-Al_2O_3$. Compared with the apparent density of pure $UO_2$, that of AlOOH added $UO_2$ powder was higher but that of PVA-Al(III) complex was lower. the densification of AlOOH added $UO_2$ pellet was initiated at about $800^{\circ}C$, the densification of PVA-Al(III) complex added $UO_2$ pellet was initiated at about $900^{\circ}C$ respectively. In a view of pore size distribution, the PVA-Al(III) complex added $UO_2$ pellet appeared as monomodal type, whereas the AlOOH added $UO_2$ pellet appeared as bimodal type. The grain size of AlOOH added $UO_2$ pellet was about $13\mu\textrm{m}$ but the grain size of PVA-Al(III) complex added $UO_2$ pellet was increased up to about $36\mu\textrm{m}$.

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.83-89
• /
• 1995

In this paper, the specimens-($Ba_{0.997}$ L $a_{0.003}$)Ti $O_{3}$ + xTi $O_{2}$, x=0.005, 0.01, 0.02, 0.03[mol]- were fabricated by a solid-state reaction method which is easy in microstructure control and good in mass production. Their crystalline structures and microstructures were analysed, and electrical properties were investigated. The perovskite-crystalline structure is confirmed by XRD, and it is exhibited by SEM that the grain grows with an addition of Ti $O_{2}$. Resistivity decreases with increasing sinteiing temperature, and the specimen of ($Ba_{0.997}$ L $a_{0.003}$)Ti $O_{3}$ + 0.02Ti $O_{2}$ sintered at 1350.deg. C shows the best PTC effects. The complex impedance plots exhibit the serial equivalent circuit of ( $R_{gb}$ / $C_{gb}$ ) and $R_{g}$ it is realized that PTC effect is attributed to the resistivity of grain boundary.ary.y.

• Current Research on Agriculture and Life Sciences
• /
• v.29
• /
• pp.29-35
• /
• 2011

The relationship between hydrologic processes and scale is one of the more complex issues in surface water hydrology. Disturbances that change vegetation and/or soil properties have been known to subsequently alter the landscape. The primary objective of this study was to estimate the grain size of soils with different properties from the hydraulic conductivity using pedotransfer functions. The double ring infiltrometer method was used to measure the vertical hydraulic conductivity of three soils under different soil planar surface treatments. Seven selected pedotransfer functions were used to estimate percentile diameters and the reduction in infiltration caused by compaction was misconstrued as caused by changes in percentile diameter. Results showed that compaction on the sandy loamy foot paths reduced the hydraulic conductivity by about 50%. The study showed that perceptual models of infiltration processes and appreciation of scale problems in modeling are far more sophisticated than normally presented in texts. Hydraulic measurement methods are still relevant and will provide significant information of grain size of the soils.

• Korean Journal of Materials Research
• /
• v.29 no.12
• /
• pp.753-756
• /
• 2019

Orthorhombic dysprosium manganite DyMnO₃ with single phase is synthesized using solid-state reaction technique and the crystal structure and dielectric properties as functions of temperature and frequency are investigated. Thermally activated dielectric relaxations are shown in the temperature dependence of the complex permittivity, and the respective peaks are found to be shifted to higher temperatures as the measuring frequency increases. In Arrhenius plots, activation energies of 0.32 and 0.24 eV for the high- and low-temperature relaxations are observed, respectively. Analysis of the relationship between the real and imaginary parts of the permittivity and the frequencies allows us to explain the dielectric behavior of DyMnO₃ ceramics by the universal dielectric response model. A separation of the intrinsic grain and grain boundary properties is achieved using an equivalent circuit model. The dielectric responses of this circuit are discerned by impedance spectroscopy study. The determined grain and grain boundary effects in the orthorhombic DyMnO₃ ceramics are responsible for the observed high- and low-temperature relaxations in the dielectric properties.

• Journal of the Korean Ceramic Society
• /
• v.33 no.1
• /
• pp.35-40
• /
• 1996

The influence of grain boundary on the electrical properties of WO3-doped SrTiO3 ceramics has been investi-gated. From the result resistivity and capacitance of grains and boundaries were obtained by employing impedance spectrocopy. And the temperature dependance of capacitance of WO3-doped SrTiO3. was influenced directly by the variation of grain boundary capacitance. It was also found by impedance spectroscopy that the dispersion frequency characteristics showed discernibly that the resistivity of the specimen varied with WO3 content.

• Korean Journal of Materials Research
• /
• v.21 no.4
• /
• pp.187-191
• /
• 2011

Prior austenite grain size plays an important role in the production of high strength hot-rolled steel. This study investigated the effect of Ti and C contents on the precipitates and prior austenite grain size. Steel with no Ti solutes had prior austenite grain size of about 620 ${\mu}m$. The addition of Ti ~ 0.03 wt.% and 0.11 wt.% reduced the prior austenite grain size to 180 ${\mu}m$ and 120 ${\mu}m$, respectively. The amount of Ti required to significantly decrease the prior austenite grain size was in the range of 0.03 wt.%. However, the amount of carbon required to significantly decrease the prior austenite grain size was not present from 0.04 wt.% to 0.12 wt.%. Oxides of Ti ($Ti_2O_3$) were observed as the Ti content increased to 0.03 wt.%. The specimen containing 0.11 wt.% of Ti exhibited the complex carbides of (Ti, Nb) C. The formation of Ti precipitates was critical to reduce the prior austenite grain size. Furthermore, the consistency of prior austenite grain size increased as the carbon and Ti contents increased. During the reheating process of hot-rolled steel, the most critical factor for controlling the prior austenite grain size seems to be the presence of Ti precipitates.