• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.1
• /
• pp.77-82
• /
• 2009

This paper reports a kinematic analysis and experimental results for the polishing process of G7 LCD glass. A kinematic analysis for the relative motion of the upper plate and lower plate has been done and computer simulation has been programmed. A series of polishing experiments has also been carried out and compared with analytical data. The experimental results agreed well with analytical ones. The experimental results indicate that the polishing removal is proportional to the relative speed and pressure.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.665-672
• /
• 1997

In this paper, sixteen column specimens were tested under the concentrated and excentric load condition to examine the structural behavior of strengthened columns. 16 column specimens were divided into four groups. One group is not strengthened, the other three groups are strengthened by the materials : 1) steel plate, 2) carbon fiber sheet, and 3) glass fiber sheet, each group is composed of four specimens. As a result, strengthened columns have larger bearing capacity and energy absorption after ultimate load than unstrengthened columns. The column group strengthened with steel plate has the best bearing capacity among the strengthened column groups. Also, the columns strengthened with the carbon fiber sheet are similar to glass fiber sheet in bearing capacity. If necessary to strengthen columns in trouble, car should be taken to treat the joint between beam and column because of crack propagation in tension side.

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.198-205
• /
• 1992

Abstract-Planarieation technology, which is essential to VLSI, has been developed using non-etch back Spin- On-Glass (SOG). Process factors for 1.5 micron double metal technology are optimized by the statistical design of experiments. Optimum conditions are found to be a process with twice SOG coating, sufficiently long hot plate baking at 300t, and furnace curing for 40 minutes below 400$^{\circ}$C.

• Current Optics and Photonics
• /
• v.8 no.5
• /
• pp.502-507
• /
• 2024

The Wollaston prism (WP) has shown promise in enabling single-shot transport-of-intensity equation (ssTIE) measurements, facilitating efficient phase retrieval in microscopy. The 1-degree prism which produces the minor beam-separation angle is used to prevent distortions. An optical-glass plate is employed in the duplicated beam path to introduce defocusing. This configuration is also advantageous when aligning the beams laterally caused by the refraction of the optical-glass plate, thus allowing another method for single-shot measurements. We applied the proposed method to image the red blood cells (RBCs), demonstrating that the proposed method could be useful in various biological and medical applications.

• Composites Research
• /
• v.29 no.6
• /
• pp.388-394
• /
• 2016

Fiber reinforced plastic (FRP) composites have drawn increasing attentions worldwide for decades due to its outstanding properties. Stress concentration factor (SCF) as an essential parameter in materials science are critically considered in structure design and application, strength assessment and failure prediction. However, investigation of stress concentration in FRP composites has been rarely reported so far. In this study, three resource-conserving analyses (Isotropic analysis, Orthotropic analysis and Finite element analysis) were introduced to plot the $K_T^A-d/W$ curve for E-glass/epoxy composite plate with the geometrical defect of circular hole placed centrally. The plates were loaded to uniaxial direction for simplification. Finite element analysis (FEA) was carried out via ACP (ANSYS composite prepost module). Based on the least squares method, a simple expression of fitting equation could be given based on the simulated results of a set of discrete points. Finally, all three achievable solutions were presented graphically for explicit comparison. In addition, the investigation into customized efficient SCFs has also been carried out for further reference.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.7
• /
• pp.994-1002
• /
• 2009

In this paper, effect of air gap thickness between absorber plate and glass cover on top heat loss of a closed loop oscillating heat pipe (CLOHP) solar collector was investigated. The CLOHP, which is made of copper with outer diameter of 3.2mm and inner diameter of 2.0mm, comprises 8 turns with heating, adiabatic and cooling section. The heating section of the heat pipe was attached to absorber plate which heated by solar simulator simulated by halogen lamps. The cooling section of the heat pipe was inserted into collector's cooling section that made of transparent acrylic. Temperatures of absorber plate, glass cover, and ambient air measured by K-type thermocouple and were recorded by MV2000-Yokogawa recorder. Top heat loss coefficients and top heat loss of the collector corresponding to some cases of air gap thickness were determined. The result of experiment shows the optimal air gap thickness for minimum top heat loss of this solar collector.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.797-800
• /
• 2002

Instead of a solution process producing amorphous $LiV_3O_8$ form, we prepared Lithium vanadate glass by melting $Li_2O-P_2O_5-V_2O_5$ and $Li_2O-P_2O_5-Bi_2O_3-V_2O_5$ composition in pt. crucible and by quenching on the copper plate. From the crystallization of $Li_2O-P_2O_5-V_2O_5$ and $Li_2O-P_2O_5-Bi_2O_3-V_2O_5$, we could abtain glass-ceramics having crystal phase, LiV3O8 from glass matrix. The material heat-treated at lower-temperature, $250^{\circ}C$ had less crystalline and lower capacity, But the material heat-treadted at higher-temperature, $330^{\circ}C$ had higher capacity and $Li_2O-P_2O_5-V_2O_5$ glass-ceramics had higher capacity than $Li_2O-P_2O_5-Bi_2O_3-V_2O_5$ glass-ceramics.

• Journal of Information Display
• /
• v.3 no.1
• /
• pp.11-16
• /
• 2002

This paper presents a study on the tubeless Plasma Display Panel (PDP) packaging using glass-to-glass electrostatic bonding with intermediate amorphous silicon. The bonded sample sealing the mixed gas with three species showed high strength ranging from 2.5 MPa to 4 MPa. The glass-to-glass bonding for packaging was performed at a low temperature of $180^{\circ}C$ by applying bias of 250 $V_{dc}$ in ambient of mixed gases of He-Ne(27 %)-Xe(3 %). The tubeless packaging was accomplished by bonding the support glass plate of $30mm{\times}50mm$ on the rear glass panel and the capping glass of $20mm{\times}20mm$. The 4-inch color AC-PDP with thickness of 8 mm was successfully fabricated and fully emitted as white color at a firing voltage of 190V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.311-315
• /
• 2000

Vanadate glass in the $LiO_2-P_2O_5-Bi_2O_3-V_2O_5$ system containing 10mol% glass fonner, $P_2O_5$ and $Bi_2O_3$ was prepared by melting the batch in pt. crucible followed by Quenching on the copper plate. We found that $LiO_2-P_2O_5-Bi_2O_3-V_2O_5$ glass-ceramics obtained from nucleation of glass showed signifieantly higher capacity and longer cycle life than conventionally made crystalline $LiV_3O_{8}$. In the present paper, we describe the charge / discharge properties during crystallization process and find the best crystallization condition of $LiO_2-P_2O_5-Bi_2O_3-V_2O_5$ glass as cathod material.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.268-269
• /
• 2008

Charging of spacecraft occurs in plasma and radiation environment. Especially, we focused on an accident caused by internal charging in a glass material that was used as the cover plate of solar panel array, and tried to measure the charge distribution in glass materials under electron beam irradiation by using a PEA (Pulsed Electro-Acoustic method) system. In the case of a quartz glass (pure $SiO_2$), no charge accumulation was observed either during or after the electron beam irradiation. On the contrary, positive charge accumulation was observed in glass samples containing metal-oxide components. It is found that the polarity of the observed charges depends on the contents of the impurities. To identify which impurity dominates the polarity of the accumulated charge, we measured charge distributions in several glass materials containing various metal-oxide components and calculated the trap energy depths from the charge decay characteristics of all glass samples.