• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.606-607
• /
• 2006

A porous material with a surface layer was fabricated using glass abrasive sludge and expanding agents. The glass abrasive sludges were mixed with expanding agents and compacted into pellets. These pellets were sintered in the range of $700-900^{\circ}C$ for 20min. The sintered porous materials had a surface layer with smaller pores and inner parts with larger pores. The surface layer and pores controlled the absorption ratio and physical properties.

• Current Optics and Photonics
• /
• 제6권4호
• /
• pp.413-419
• /
• 2022

An oxyfluoride glass ceramic containing Eu²⁺-doped nepheline and LaF₃ crystals was modified, with BaF₂ replacing LaF₃ up to 20 mole percent, and its luminescence change was monitored. With increasing BaF₂ content, the greenish yellow emission centered at 540 nm under 400-nm excitation decreased, and a new afterglow emission from the modified ceramic was observed after removal of the excitation light source. X-ray diffraction (XRD) and transmission electron microscopy with energy dispersive spectroscopy (TEM-EDS) were used to investigate the changes in the crystalline phases within the glass matrix. Time dependent emission intensity was monitored to observe the afterglow, and the possible mechanism for the afterglow due to BaF₂ addition was considered.

• 한국세라믹학회지
• /
• 제50권3호
• /
• pp.238-243
• /
• 2013

We investigated the effect of Pb-metal filler added to a hybrid paste(PbO-$Bi_2O_3-B_2O_3$-ZnO glass frit and Pb-powder), for joining flip-chip sat lower temperatures than normal. The glass transition temperature was detected at $250^{\circ}C$ and the softening point occurred at $330^{\circ}C$. As the temperature increased, the specific density decreased due to the volatility of the Pb-metal and boron component in the glass. When the glass was heat-treated at $350^{\circ}C$ for 5 min, XRD results revealed a crystalline $Pb_4Bi_3B_7O_{19}$ phase that had been initiated by the addition of Pb-filler in the hybrid paste. The addition of the Pb-metal filler caused are action between the Pb-metal and glass that accelerated the formation of the liquid phase. The liquid phase that formed, promoted bonding between the flip-chip substrate sat lower temperature.

• 한국세라믹학회지
• /
• 제46권4호
• /
• pp.413-418
• /
• 2009

Glass systems based on Ca, Sr, Ba, and Zn modified alumino-boro silicates were investigated in order to improve the dielectric and mechanical properties of a typical LTCC (low temperature co-fired ceramic) which was developed for high frequency highly-integrated modules. The glass was prepared by a typical melting procedure and then mixed with cordierite fillers to fabricate glass/ceramic composite-type LTCC materials. The amount of cordierite filler was fixed at 50 volumetric%. For an optimal glass composition of 7.5% CaO, 7.5% BaO, 5% ZnO, 10% $Al_2O_3$, 30% $B_2O_3$, and 40% $SiO_2$ in mole ratio, the resultant LTCC composite showed a dielectric constant of 5.8 and a dielectric loss ($tan{\delta}$) of 0.0009 after firing at $900^{\circ}C$. An average bending strength of 160MPa was obtained for the optimal composition.

• 한국결정성장학회지
• /
• 제20권1호
• /
• pp.43-52
• /
• 2010

삼척 도계지역의 탄광에서 석탄채취시에 발생되는 석탄폐석을 이용하여 유리를 제조하였다. 소다라임계 화학조성을 갖는 유리를 제조하기 위하여 화학원료로서 소다회, 탄산칼슘 등의 원료를 추가로 사용하였고, 화학원료인 탄산칼슘 대신에 천연광물원료인 석회석을 사용하였을 때의 특성을 검토하였다. 전기로를 사용하여 $1,550^{\circ}C$에서 1시간 용응하여 투명한 유리를 제조할 수 있었다. 석탄폐석의 종류 및 파유리의 종류에 따라 다양한 종류의 유리샘플이 제조되었다. 유리샘플의 투과율 및 색차와 같은 광학적 특성을 UV/VIS/NIR Spectrometer를 이용하여 측정하였고, 또한 열팽창계수 및 연화점과 같은 열적특성도 측정하였다. 그 결과, 일반 선탄경석으로는 70% 이상의 가시광선투과율을 갖는 투명한 유리를 제조할 수 있었으며, 또한 쉘(shell) 타입의 선탄경석으로는 0~35%의 가시광선 투과율을 갖는 검정색의 칼라유리를 제조할 수 있었다. 따라서 석탄폐석을 이용하여 건축재료로서 유리타일이나 발포유리와 같은 유리 2차제품을 제조하는데 활용할 수 있으리라 판단되었다.

• 한국표면공학회지
• /
• 제50권5호
• /
• pp.301-307
• /
• 2017

The purpose of this study is to investigate the electrical properties of thick-film resistor (TFR) prepared from $CaO-ZnO-B_2O_3-Al_2O_3-SiO_2$ (CZBAS) glass containing $RuO_2$ particles. $RuO_2$-glass composite powder was made by mixing and melting oxide powders of constituents. For comparison, $RuO_2$ powder was simply mixed with glass powder. $RuO_2$-40wt% glass composite and mixture were dispersed in an organic binder to obtain printable resistor paste and then thick-film was formed by screen printing, followed by sintering at the range between $750^{\circ}C$ and $900^{\circ}C$ for 10 min with a heating rate of $50^{\circ}C/min$ in an ambient atmosphere. $RuO_2$-glass composite sample showed much higher resistance compared to the simple mixed sample. This could be attributed to the difference in conducting mechanism. After sintering at $850^{\circ}C$, temperature coefficient of resistance of composite sample was lower than that of simple-mixed sample. TFR with dense and homogeneous microstructure could be obtained by using $RuO_2$-glass composite powder.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.49-49
• /
• 2007

Glass infiltration 방법을 이용하여 '$A_2O_3$/Glass/$Al_2O_3$' 구조의 무수축 LTCC 기판을 제조하였다. Glass infiltration 법에 의한 무수축 기판 제조에 있어 가장 중요한 요소로는 Glass의 점성은 낮고, alumina에 대한 Glass의 젖음성 (wettability)이 좋으며. 낮은 반응성이 요구되기 때문에 Glass의 조성 선정이 무엇보다 중요하다. 본 연구에서는 Na, Pb, Mg 계열의 각기 다른 glass들의 alumina에 대한 젖음성을 평가하여 젖음성 및 치밀성이 우수한 Pb 계열의 Glass를 이용하여 LTCC 기판으로 적용 가능한 온도인 $700{\sim}900^{\circ}C$에서 '$A_2O_3$/Glass/$Al_2O_3$'구조의 glass infiltration 특성을 고찰하였다. 소성 후 수축율은 x-y축 0.2%, Z축 40%, 밑도 $3.8g/cm^3$, 유전율 6.8, 품질계수 552로 무수축 기판으로서의 적용 가능성을 확인하였다.

• 한국전기전자재료학회논문지
• /
• 제20권1호
• /
• pp.19-24
• /
• 2007

The effects of $B_2O_3-SiO_2-R(R;CaO,\;BaO,\;ZnO,\;Bi_2O_3)$ borosilicate glass system on the sintering behavior and microwave dielectric properties of ceramic/glass composites were investigated as functions of modifier, glass addition ($30{\sim}50\;vol%$) and sintering temperature ($500{\sim}900^{\circ}C$ for 2 hrs). The addition of 50 and 45 vol% glass ensured successful sintering below $900^{\circ}C$. Sintering characteristics of the composites were well described in terms of modifier. Borosilicate glass enhanced the reaction with $Al_{2}O_{3}$ to form pores, second phases and liquid phases, which was responsible to component of modifier. Dielectric constant (${\varepsilon}_{r},\;Q{\times}f_{o}$) and temperature coefficient of resonant frequency (${\tau}_{f}$) of the composite with 50 and 45 vol% glass contents($B_{2}O_{3}:SiO_{2}:R=25:10:65$) demonstrated A-CaBS(7.8, 2,560 GHz, -81ppm/$^{\circ}C$), A-BaBs(5.8, 3.130 GHz, -64 ppm/$^{\circ}C$), A-ZnBS(5.7, 17,800 GHz, -21 ppm/$^{\circ}C$), A-BiBs(45 vol% glass in total)(8.3, 2,700 GHz, -45 ppm/$^{\circ}C$) which is applicable to substrate requiring an low dielectric properties.

• 한국세라믹학회지
• /
• 제48권1호
• /
• pp.80-85
• /
• 2011

The crystallization behavior and microstructural change of the glass-ceramics were analyzed as a function of concentration and etching time of the HF solution in order to enhance the degree of crystallinity induced by heterogeneous nucleation of glass of bottom ash containing 15 wt% $Li_2O$. The nucleation site seemed to be generated where the Si ion was eluted. The main crystal phases in the glass-ceramics fabricated in this study were $\beta$-spodumene and $Li_2SiO_3$. The specimens etched with HF of 0.5 vol% within 0~60 seconds showed increased crystalline peak intensities in XRD pattern with etching time compared to no-etched one. Also the crystal size and crystal occupancy in the glass matrix observed by SEM were increased with etching time. For the glass-ceramics etched with 1.0 and 2.0 vol% HF solution, the etching time over 10 s was not effective to increase the crystallinity. From this study, it was found that the glass-ceramics with the higher crystallinity could be obtained by HF-etching followed by heat treatment process, even though the nucleating agent or 2-stages thermal treatment process were not used.

• 한국세라믹학회지
• /
• 제29권10호
• /
• pp.827-835
• /
• 1992

The effects of CeO2 on the properties of cordierite-based glass-ceramics and its applicability to low firing temperature substrate were examined. Glass-ceramics were prepared by sintering the glass powder compacts at 900~100$0^{\circ}C$ for 3 h. Density, bending strength, dielectric constant and thermal expansion coefficient of the glass-ceramics were measured as functions of CeO2 contents and sintering temperatures. By adding CeO2, dense glass-ceramics were obtained below 100$0^{\circ}C$. dielectric constant and bending strength were more dependent on the porosity of glass-ceramics containing 5 wt% CeO2, sintered at 100$0^{\circ}C$ for 3 h, were as follows; relative density is 95.3%, bending strength is 178$\pm$11 MPa, dielectric constant is 4.98$\pm$0.20 (at 1 MHz) and thermal expansion coefficient is 33.7$\times$10-7/$^{\circ}C$. Therefore, the glass-ceramics containing 5 wt% CeO2 appeared to be suitable for low firing temperature substrate of electronic devices.