• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.654-657
• /
• 2003

We obtained amorphous calcium carbonate through the carbonation reaction of $Ca(OH)_2$, and through this reaction, observed changes in particle shape and phase by electric conductivity, XRD and TEM analysis. According to the result of the analysis, in the first declining stage of electric conductivity, amorphous calcium carbonate that has formed is coated on the surface of $Ca(OH)_2$ and obstructs its dissolution, and in the first recovery stage of electric conductivity, amorphous calcium carbonate is dissolved and re-precipitated and forms chains of fine calcite particles linearly joined. In the second decline of conductivity, viscosity increases due to the growth of chains of calcite particles, and finally the calcite particles are dissolved and separated into colloidal crystalline calcite, thereby increasing electric conductivity again.

• 한국전산유체공학회:학술대회논문집
• /
• 1998.05a
• /
• pp.128-137
• /
• 1998

In this numerical experiment, the preconditioned compressible Navier-Stokes equation is tested to analyze the laminar spray combustion. Sprayed flow field is formulated by Eulerian-Lagrangian system for the gas and liquid phases each. DSF(Deterministic Separated Flow) model was adopted for the sprays with the vortex model to describe transients of individual droplet heating. Simplified single global reaction model approximates methanol-air reaction with and without disk flame holder. The equation system is discretized by finite difference technique and time integrated by LU-SGS. Due to greatly simplified chemical reaction mechanism and the lack of experimental evidences, most of the efforts were devoted to show the applicability and robustness of preconditioned compressible flow calculation algorithm. Computation results in qualitatively reasonable combusting flow field, hence it is believed that further refinement are required to produce quantitatively accurate solutions.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.7
• /
• pp.1563-1566
• /
• 2009

One-dimensional aluminum nitride (AlN) nanostructures were synthesized by calcining an Al(OH)(succinate) complex, which contained a very small amount of iron as a catalyst, under a mixed gas flow of nitrogen and CO (1 vol%). The complex decomposed into a homogeneous mixture of alumina and carbon at the molecular level, resulting in the lowering of the formation temperature of the AlN nanostructures. The morphology of the nanostructures such as nanocone, nanoneedle, nanowire, and nanobamboo was controlled by varying the reaction conditions, including the reaction atmosphere, reaction temperature, duration time, and ramping rate. Iron droplets were observed on the tips of the AlN nanostructures, strongly supporting that the nanostructures grow through the vapor-liquid-solid mechanism. The variation in the morphology of the nanostructures was well explained in terms of the relationship between the diffusion rate of AlN vapor into the iron droplets and the growth rate of the nanostructures.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.2
• /
• pp.232-238
• /
• 2016

In this study, a liquid carbonation method was applied for producing precipitate calcium carbonate by liquid-liquid reaction. Also a shuttle mechanism of wet chemical absorption using MEA was utilized. The high concentration $CO_2$(A) and exhaust gas(B) was used for collecting carbon dioxide in the 30% MEA aqueous solution, and $CO_2$ was fixed with rate of 0.35 mg of $CO_2$ per mg of sludge through the liquid carbonation process. It was found from SEM data that calcium carbonate was mainly made up with spherical vaerite with the mixing of a small quantity of calcite.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.10
• /
• pp.1508-1512
• /
• 2004

A gas chromatography/mass spectrometric (GC/MS) method has been developed for the determination of trace mono-n-butyltin (MBT), di-n-butyltin (DBT), and tri-n-butyltin (TBT) compounds in sediments. Samples were extracted by 10% acetic acid in methanol containing 0.03% tropolone and were then derivatized for GC/MS analysis. Ethylation by sodium tetraethylborate and phenylation by sodium tetraphenylborate were evaluated as a derivatization reaction of the organotins in sample extract. n-Hexane was added into reaction media in the beginning of the reaction for the continuous extraction of derivatized organotins. Ethylation requires less than 2 hours to get proper derivatization yields for MBT, DBT, and TBT altogether and produces relatively low amounts of side reaction products. Compared to ethylation, phenylation requires much longer time but provides relatively lower yield and produces considerable amounts of side reaction products. Therefore, the ethylation reaction was applied for the analysis of organotin compounds in sediment. An isotope dilution mass spectrometric (IDMS) method based on GC/MS has been applied to the accurate determination of DBT compounds in the sediments. The IDMS results from the analyses of sediment samples showed a reasonable repeatability and a good agreement with the values obtained by IDMS based on liquid chromatography/induced coupled plasma/mass spectrometry.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.380-385
• /
• 2009

The absorption rate of carbon dioxide with 2-amino-2-methyl-1-propanol(AMP) was measured in such non-aqueous solvents as methanol, ethanol, n-propanol, n-butanol, ethylene glycol, propylene glycol, and propylene carbonate, and in water at 298 K and 101.3 kPa using a semi-batch stirred tank with a plane gas-liquid interface. The overall reaction rate constant, obtained under the condition of fast reaction regime, from the measured rate of absorption was used to get the elementary reaction rate constants in complicated reactions represented by reaction mechanism of carbamate formation and the order of overall reaction of $CO_2$ with amine. The correlation between the elementary reaction rate constant and the solubility parameter of the solvent was also presented.

• Journal of the Korean Wood Science and Technology
• /
• v.19 no.4
• /
• pp.80-84
• /
• 1991

Lignocellulosic biomass including acetosolv ricestraw and spruce lignin were liquefied and converted into liquid hydrocarbons by catalytic hydroliquefaction reaction. These experimental works were carried out in 1-liter-capacity autoclave using 50% tetralin and m-cresol solution respectively as soluble solvent and Ni. Pd. Fe and red mud as catalyst. $H_2$ gas was supplied into the reactor for escaltion of deoxhydroenolysis reaction. Catalyst concentrations were 1 % of raw material based on weight. The ratio between raw materials and soluble solvent are 1g and 10cc. The reaction conditions are 400-$700^{\circ}C$ of reaction temperature, 10-50 atms of reaction pressure. The highest yield of hydrocarbon, so called "product oil" showed 32% and 5.5% of lowest char formation when red mud was used as catalyst. The product oil yields from those of other catalysts were in the range of 20-29%. The influence of different initial hydrogen pressures was examined in the range d 30-50 atms. A minimum pressure of 35 atms was necessary to obtain a complete recovery of souble solvent for recycling.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.553-556
• /
• 2005

Pyrolysis of polyethylene was carried out in the stainless steel reactor of internal volume of $40cm^3$. Pyrolysis reactions were performed at temperature $390-450^{\circ}C$ and the pyrolysis product were collected separately as reaction products and gas products. The molecular weight distributions(MWDs) of each liquid product were determined by GC-SIMDIS. Molecular weight of each product were decreased wi th increase of react ion temperature and time.

• Proceedings of the KIEE Conference
• /
• 2008.05a
• /
• pp.201-202
• /
• 2008

Formation of pores in melt processed ceramics oxides and its effect on the microstructure were studied. Spherical Pores with a size of a few tens of microns were formed due to the evolution of oxygen gas during melting of a oxide. The liquid pockets were converted into sperical oxide regions with a lower oxide density through the peritectic reaction during subsequent fabrication.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.867-870
• /
• 2007

In order to solve image sticking phenomena, the gas-phase and liquid-phase interfacial reactions of photosensitive polyimide can annihilate photoreactive carbon-carbon double bonds, which remain after photo-alignment process. The annihilation processes dramatically affect residual DC and photochemical reorientation of photoactive functional groups.