• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.104-110
• /
• 2006

A design and control of electrostatic suspension system for flexible objects is presented. A number of electrode pairs of which the number depends on the object flexibility are positioned above the object and the voltages applied to each electrode pair are controlled, independently on the others, on the basis of the gap length. To implement the system with low cost and compactness, switched-voltage control scheme that is based on the relay feedback control is utilized. Relay feedback control method deploys only a single high-voltage power supply that can deliver a DC voltage of positive and/or negative polarity and thus high voltage amplifiers that are costly and bulky are not needed any more. It is shown that despite the inherent limit cycle property of the relay feedback based control, an excellent performance in vibration suppression is attained due to the presence of a relatively large squeeze film damping originating from the electrodes and levitated object. Employing fourteen electrode pairs, a thin aluminum plate with a thickness of 0.1 mm has been suspended at a gap length of 0.75mm.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1759-1764
• /
• 2015

Glow corona is a kind of streamer-free corona that can suppress upward leaders in transmission lines. Thus, it has good application potential in lightning protection. This paper investigates its corona characteristics. The suppression characteristic of glow corona on streamer is studied in air gap under negative DC voltage by wrapping thin wires on the electrode. The effect of thin wire winding patterns on the gap breakdown voltage is analyzed. Results are considered to be attributed to the inception condition of glow corona. Thus an inception test of glow corona is also conducted, and the inception voltage is obtained. Results show that the inception voltage decreases with short winding pitch. Thus an investigation on the inception of glow corona influenced by thin wire is conducted, and an influential factor is proposed to evaluate the influence. The inception regular of thin wire glow corona presented in this paper has certain reference value for the application of glow corona in transmission lines.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.1
• /
• pp.4-7
• /
• 2002

Samples of $Nb/Al-AlO_x/Nb$ tunnel junction with the size of $50 ${\mu}{\textrm}{m}$ {\times} 50 ${\mu}{\textrm}{m}$$ were fabricated by using self-aligning and reactive ion etching technique In the high quality samples, the $V_m$ value (the product of the critical current and subgap resistance measured at 2 mV) was 34 mV at the critical current density of $J_c: 500 A/cm^2 and the V_g$ value (the gap voltage) was 2.8 mV. For the higher $J_c$ sample, voltage fluctuation at the gap voltage was observed. The $V_m and J_c$ values for this sample were 8 mV and 900 A/cm$^2$, respectively. Also, the relationship between critical current density $J_c$ and specific normal conductance $G_s$ of the junctions with $J_c$ in the range of 28 A/cm$^2$~940 A/cm$^2$was investigated.

• Journal of Korea Society of Industrial Information Systems
• /
• v.21 no.2
• /
• pp.39-44
• /
• 2016

Using the welding current and voltage signal processing, we have studied the influence that the diameter of the welding wire to the welding quality detection. For the experiments, We have analyzed the signal with respect to large and small artificially a gap between base materials than the welding wire. In this experiment, the 1.2 mm diameter of the welding wire was used, and distance between the welding base materials was respectively 1.0 mm and 2.0 mm. In the welding with a large defect than the diameter of the welding wire it was able to detect a change in the welding current and welding voltage. But it could not detect a change in the welding current and welding voltage in the welding has a small defect than the welding wire diameter.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.7 no.1
• /
• pp.36-39
• /
• 2014

MFC(microbial fuel cell) is the device to produce the electricity by using the microbes which are living in the waste water. In this paper, the electric characteristics of the MFC were investigated according to each different structure and electrode materials. The voltage being reversed phenomenon was observed in the MFC which uses the cupper plate as the cathode material. This result comes from the oxidation reaction of the cupper plate electrode in this MFC. And this MFC has lower output voltage than one that has a platinum plate electrode. The smaller gap distance of the cupper plate electrode of the MFC showed the higher output voltage. The larger electrode area of the cupper plate electrode showed that the reaching time of the output voltage to the maximum value was delayed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.1
• /
• pp.3-11
• /
• 1998

The influence due to particle contaminated on spacer surface is remarkable in the decreasing of dielectric strength in SF6 GIS. In relation with this problem, We studied, AC flash-over voltage characteristics and breakdown mechanism are investigated under metallic and insulating particle initiated condition in SF6 gas by varying the particle position, particle shape with a plane-plane electrode. The main results are as follows $\circled1$ Influence of the flash-over voltage decrease for particle position is lowest in mid gap and is highest in separated small gap on electrode. $\circled2$ The metallic particle shape which results in the more reduced flash-over voltage, the FOV saturation moved in to the region of low pressure. $\circled3$Insulating particle less than 0.6[mm] are not almost influenced by the flash-over Voltage.oltage.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.622-627
• /
• 2019

This paper propose an initial rotor position detection method for sensorless operation of a single-phase permanent magnet synchronous motor(SP-PMSM) with asymmetric air-gap. In general, the sensorless control based on back-emf estimation is difficult to estimate the back-emf at the zero and low speed regions. For this reason, an open loop start-up technique is indispensable, and it is also necessary to detect the initial position of the rotor in order to rotate in a certain direction. In this paper, we propose a method to detect rotor polarity by adding offset voltage to high frequency voltage signal based on the magnetic characteristics of SP-PMSM. The validity and usefulness of the proposed algorithm are verified through several experimental results.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.45-51
• /
• 2007

We designed and fabricated the planar graded-gap injector GaAs Gm diodes with $1.6{\mu}m$ active length for operation at 94 GHz. The fabrication of the Gunn diode is based on MESA etching, Ohmic metalization, and overlay metalization. The measured negative resistance characteristics of the graded-gap injector GaAs Gunn diodes are examined for two different device structures changing the distance between the cathode and the anode electrodes. Also, we discuss the DC results under the forward and the reverse biases concerning the role of the graded-gap injector. It is shown that the structure having the shorter distance between the cathode and the anode electrode has higher peak current, higher breakdown voltage, and lower threshold voltage than those of the larger distance.

• Journal of radiological science and technology
• /
• v.3 no.1
• /
• pp.57-66
• /
• 1980

X-ray grid is the most important means to reduce the scattered ray from patients, but alternative way is air gap technique that is another name of Groedel technique. This technique is mainly used in chest radiography. Authors performed an experimental study on the air gap technique for chest radiography and obtained the results as follows; 1. In using the high voltage air technique, scattered ray could be reduced effectively, while the percentage of scattered ray was slightly increased than conventional grid technique. 2. In film contrast, 30cm air gap technique was inferior to 12:1 grid technique and contrast improvement was increased when the object was thicker and higher voltage was used. 3. The patient exposure dose was reduced about $25{\sim}45%$ compared with conventional grid technique by air gap technique used.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.8
• /
• pp.477-486
• /
• 2000

This paper presents Pspice modeling methods for spark gaps and ZnO varistors and describes the application for the two-stage surge suppression circuit which was composed of the nonlinear components. The simulation modelings of nonlinear components were conducted on the basis of the voltage and current curves measured by the impulse current with the time-to-crest of $1~50 \mus$ and the impulse voltage with the rate of the time-to-crest of 10, 100 and 1000 V/\mus$. The firing voltages of the spark gap increased with increasing the rate of the time-to-crest of impulse voltage and the measured data were in good agreement with the simulated data. The I-V curves of the ZnO varistor were measured by applying the impulse currents of which time-to-crests range from 1 to $50 \mus$ and peak amplitudes from 10 A to 2 kA. The simulation modeling was based on the I-V curves replotted by taking away the inductive effects of the test circuit and leads. The meximum difference between the measured and calculated data was of the order of 3%. Also the two-stage surge suppression circuit made of the spark gap and the ZnO varistor was investigated with the impulse voltage of $10/1000\mus$$mutextrm{s}$ wave shape. The overall agreement between the theoretical and experimental results seems to be acceptable. As a consequence, it was known that the proposed simulation techniques could effectively be used to design the surge suppression circuits combined with nonlinear components.