• International Journal of Highway Engineering
• /
• v.17 no.1
• /
• pp.91-98
• /
• 2015

PURPOSES : Although signalized intersections have been considered the best way to control traffic volume in urban areas for several decades, roundabouts are currently being discussed as an alternative way to control traffic volume, especially when traffic is light. Because a roundabout's efficiency depends on the load geometry as well as the traffic volume, design guidelines for roundabouts are recommended only if the incoming traffic volume is very low. It is rare to substitute a roundabout for an existing signalized intersection in urban areas. This study aims to estimate the benefits from the transformation of an existing signalized intersection into a roundabout in an urban area. When there is a more moderate volume of traffic, roundabouts can be effectively used by optimizing signals located at an approaching roadway. METHODS : The methodologies of this paper are as follows: First, a signalized intersection was analyzed to determine the traffic characteristics. Second, the signalized intersection was transformed into a roundabout using VISSIM microscopic traffic simulation. Then, we estimated and analyzed the effects and the performance of the roundabout. In addition, we adjusted a method to improve the benefits of the transformation via the optimization of signals located at an approaching road to control the incoming traffic volume. RESULTS : The results of this research are as follows: The signal-optimized roundabout improved delays compared with the signalized intersection during the morning peak hour, non-peak hour, and evening peak hour by 1.78%, 12.45%, and 12.72%, respectively. CONCLUSIONS : According to the simulation results of each scenarios, the signal-optimized roundabout had less delay time than the signalized intersection. If optimized signal control algorithms are installed in roundabouts in the future, this will lead to more efficient traffic management.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.4
• /
• pp.637-642
• /
• 2020

In this study, the SLB(Sidelobe Blanking)/BLB(Blacklobe Blanking) design of the VHF band radar using the low-frequency band having a relatively larger beam width than the S-band or X-band radar. The antenna of the VHF band has a relatively large beam width, so it is reflected from the side lobe. If the reflected target signal is not processed into sidelobe, the false alarm rate of the radar increases by recognizing it from the main lobe signal. This method of SLB blocking is the elimination of the side lobe signal in the front of the array antenna using the central radiating element of the array antenna, and the blocking of side lobe signal from the antenna rear through BLB receiver block. After completed the radar implementation, The function of blocking of side lobe signals was confirmed through the system unit test by Simulated signal generator. Through this study, it will be used in the implementation of the side-lobe blocking technology of the array antenna for low-frequency band radar with large antenna size and beam width in the future.

• Journal of Convergence for Information Technology
• /
• v.9 no.8
• /
• pp.148-154
• /
• 2019

The purpose of this study is to review systematically the literatures on the research of the elderly speech signal processing based on the domestic gender innovation and to introduce the utility and innovation of the gender analysis methods. From 2000 to present, among the 37 research papers published in the Korean Journal, 25 papers were selected according to the inclusion and exclusion criteria. And gender analysis methods were applied to gender research subject and design. Research results show diversity of research field and high gender recognition of R & D team are needed in research and development of engineering of gender innovation perspective. In addition, government-level regulation and research funding should be systematically applied to gender innovation research processes in the elderly voice signal processing and various gender innovation projects. In the future gender innovation in the elderly speech signal processing can contribute to the creation of a new market by developing a voice recognition system and service that reflects the needs of both men and women.

• Investigative Magnetic Resonance Imaging
• /
• v.26 no.2
• /
• pp.125-134
• /
• 2022

Purpose: The aim of this study was to investigate the change in signal sensitivity over different acquisition start times and optimize the scanning window to provide the maximal signal sensitivity of [1-¹³C]pyruvate and its metabolic products, lactate and alanine, using spatially localized hyperpolarized 3D ¹³C magnetic resonance spectroscopic imaging (MRSI). Materials and Methods: We acquired 3D ¹³C MRSI data from the brain (n = 3), kidney (n = 3), and liver (n = 3) of rats using a 3T clinical scanner and a custom RF coil after the injection of hyperpolarized [1-¹³C]pyruvate. For each organ, we obtained three consecutive 3D ¹³C MRSI datasets with different acquisition start times per animal from a total of three animals. The mean signal-to-noise ratios (SNRs) of pyruvate, lactate, and alanine were calculated and compared between different acquisition start times. Based on the SNRs of lactate and alanine, we identified the optimal acquisition start timing for each organ. Results: For the brain, the acquisition start time of 18 s provided the highest mean SNR of lactate. At 18 s, however, the lactate signal predominantly originated from not the brain, but the blood vessels; therefore, the acquisition start time of 22 s was recommended for 3D ¹³C MRSI of the rat brain. For the kidney, all three metabolites demonstrated the highest mean SNR at the acquisition start time of 32 s. Similarly, the acquisition start time of 22 s provided the highest SNRs for all three metabolites in the liver. Conclusion: In this study, the acquisition start timing was optimized in an attempt to maximize metabolic signals in hyperpolarized 3D ¹³C MRSI examination with [1-¹³C] pyruvate as a substrate. We investigated the changes in metabolic signal sensitivity in the brain, kidney, and liver of rats to establish the optimal acquisition start time for each organ. We expect the results from this study to be of help in future studies.

• Journal of Positioning, Navigation, and Timing
• /
• v.4 no.3
• /
• pp.107-114
• /
• 2015

Binary Offset Carrier (BOC) signal planned for future Global Navigation Satellite System (GNSS) provided better positioning accuracy and smaller multipath error than GPS C/A signal. However, due to the multiple side peaks in the auto-correlation function (ACF) of the BOC modulated signals, a receiver may false lock onto one of the side peaks in the tracking mode. This false lock would then result in a fatal tracking error. In this paper, we propose an unambiguous tracking method for composite BOC (CBOC) signals to mitigate this problem. It aims to reduce the side peaks of the ACF of CBOC modulated signals. It is based on the combination of traditional CBOC correlation function (CF) and reference CF of unmodulated pseudo- random noise code (PRN code). First, we present that cross-correlation function (CCF) with unmodulated PRN code is close to the secondary peaks of the traditional CBOC. Then, we obtain an unambiguous correlation function by subtracting traditional CBOC ACF from these CFs. Finally, the tracking performance for the CBOC signals is examined, and it is shown that the proposed method has better performance than the traditional unambiguous tracking method in additive white Gaussian noise (AWGN) channel.

• Proceedings of the KIEE Conference
• /
• 2001.11c
• /
• pp.376-379
• /
• 2001

In this paper, I design the control chip that controls inner test sequence of Logic Tester to test chip. Logic tester has the thirteen inner instructions to control test sequence in test. And these instructions are saved in memory with test pattern data. Control chip generates address and control signal such as read, write signal of memory. Before testing, necessary data such as start address, end address, etc. are written to inner register of control chip. When test started, control chip receives the instruction in start address and executes, and generates address and control signals to access tester' inner memory. So whole test sequence is controlled by making the address and control signal in tester's inner memory. Control chip designs instruction's execution blocks, respectively. So if inner instruction is added from now on, a revision is easy. The control chip will be made using FPGA of Xilinx Co. in future.

• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.569-583
• /
• 2013

In this study, the simultaneous use of a multi-level converter (MLC) as a DC-motor drive and as an active battery cell balancer is investigated. MLCs allow each battery cell in a battery pack to be independently switched on and off, thereby enabling the potential non-uniform use of battery cells. By exploiting this property and the brake regeneration phases in the drive cycle, MLCs can balance both the state of charge (SoC) and temperature differences between cells, which are two known causes of battery wear, even without reciprocating the coolant flow inside the pack. The optimal control policy (OP) that considers both battery pack temperature and SoC dynamics is studied in detail based on the assumption that information on the state of each cell, the schedule of reciprocating air flow and the future driving profile are perfectly known. Results show that OP provides significant reductions in temperature and in SoC deviations compared with the uniform use of all cells even with uni-directional coolant flow. Thus, reciprocating coolant flow is a redundant function for a MLC-based cell balancer. A specific contribution of this paper is the derivation of a state-space electro-thermal model of a battery submodule for both uni-directional and reciprocating coolant flows under the switching action of MLC, resulting in OP being derived by the solution of a convex optimization problem.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.2
• /
• pp.129-136
• /
• 2011

The aim of this paper is to present the method of identifying the impact location on the plate. This basic research has the future purpose to achieve the human-interaction technology based on the signal processing, piezoelectric materials, and wave propagation. The present work concerning the location identification of a single impact on the plate simulated the waveform numerically generated by impact force and applied the SWFOM(sliced Wigner higher fourth order moment) to the waveform to get the arrival time differences due to impact force between three sensors attached to the plate. The simulated signal is useful to get the information for time interval for the only direct wave. This information is used the source localization by using experimental work. The measured signal is also used for source localization of a single impact based on the higher order time frequency as a novel work.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.11
• /
• pp.1113-1120
• /
• 2003

It is expected in the future that the demand of optical subcarrier multiplexing system, in which a number of small size base stations with only antenna and RF transmission are connected to central station using optical fiber, will be increased in the CDMA digital cellular mobile communication network. In this paper, in order to analysis the performance of optical SCM system fur CDMA RF signal transmission, MZ modulator is modelled as a non-linear transfer function with cubic operation. The performance degradation due to multipath signals and other user signals through MB modulator is analyzed and the performance is improved using the Rake receiver.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.12
• /
• pp.2769-2774
• /
• 2010

In this paper, we have proposed sideband injection locking method, heterodyne technique, to generate millimeter-wave signal. Microwave signals in cellular broadband mobile communication networks and distributed networks can favorably be generated and distributed by optical techniques. In principle, these techniques have already been investigated for optical control of phase-array antennas, characterization of photo-detector and phase locking of millimeter-wave oscillators and now being applied to wireless communications. The generation and transmission of millimeter-wave radio signals by optical means is of interest for future pico-cell broadband mobile communication system, especially for systems operating at frequencies of tens of GHz applicable to LMDS. We experimented and analysed the generation of millimeter wave signal.