• 한국자동차공학회논문집
• /
• 제11권2호
• /
• pp.63-68
• /
• 2003

The purpose of this study was to investigate reduction of exhaust gas temperature in LPG conversion engine from diesel. A conventional diesel engine was modified to a LPG(Liquified Petroleum Gas) engine that diesel fuel injection pump was replaced by the LPG fuel system. The research was peformed with measurement of exhaust gas temperature by varying spark ignition timing, air-fuel ratio, compression ratio, EGR ratio and different compositions of butane and propane. The major conclusion of this work were followed. (i) Exhaust gas temperature was decreased and power was increased with the advanced spark ignition timing. (ii) Exhaust gas temperature was decreased with lean and rich air-fuel ratio. (iii)Exhaust gas temperature was decreased and power was increased with the higher compression ratio. (iv) Engine power and exhaust temperature were not influenced by varied butane/propane fuel compositions. (v) Finally, one of the important parameters in reduction of exhaust gas temperature is spark ignition timing among the parameters in this study.

• 한국전기전자재료학회논문지
• /
• 제33권6호
• /
• pp.505-509
• /
• 2020

The development of diesel power generation is predominantly geared toward island areas or ships because diesel exhibits weak scale-merit characteristics and power quality problems, which are associated with environmental pollution. However, a new energy paradigm, distribution energy resource (DER), has been emerging as a renewable energy source due to the existing structural problems in waste disposal and complex factors such as the conversion technology of waste emulsified oil (WDF). By combining extended producer responsibility (EPR) support and renewable energy certificates (REC), including waste energy REC 0.25 for other bioenergy and REC 1.0 for power transactions, an adequate profit model can be built through self-energetic power generation, thereby drawing keen attention from related industries. Therefore, if WDF is used appropriately as a high-quality engine fuel, it can lead to the development of various fields such as novel renewable energy sectors, waste management, and EPR-related industries. This study is intended to produce WDF using plastic waste by using it as engine-generator fuel. Moreover, we investigate ways to improve the quality and suitability of WDF as an engine fuel.

• 에너지공학
• /
• 제16권2호
• /
• pp.73-82
• /
• 2007

세계 에너지 수요는 개발도상국을 중심으로 하여 폭발적으로 증가하고 있는 반면 땅 속에 매장되어 있는 화석연료는 점점 줄어들고 있고 화석연료의 사용으로 발생되는 지구 환경오염도 해결해야 할 중요한 과제이다. 이 시점에서 화석연료의 활용도를 높이고 환경친화적인 연료로의 개발이 매우 필요가 있다. 최근 이러한 문제를 해결할 수 있는 연료로서 제시되고 있는 DME 연료에 대하여 국내?외 기술개발, 보급 및 시장현황을 소개하고자 한다.

• 한국수소및신에너지학회논문집
• /
• 제21권6호
• /
• pp.493-499
• /
• 2010

Steam reforming (SR) of glycerol, a main by-product of manufacturing process of bio-diesel, for the production of hydrogen was investigated over the Ni-based catalysts. The Ni-based catalysts were prepared by an impregnation method, and characterized by $N_2$ physisorption, CO chemisorption, XRD and TEM techniques. It was found that the Ni/${\gamma}-Al_2O_3$ catalyst showed higher conversion and catalytic stability for the carbon formation than the other catalysts in the steam reforming of glycerol under the tested conditions. The results suggest that the steam reforming of glycerol over modified Ni/${\gamma}-Al_2O_3$ catalyst minimized carbon formation can be applied in hydrogen station for fuel-cell powered vehicles and fuel processor for stationary and portable fuel cells.

• 한국생물공학회:학술대회논문집
• /
• 한국생물공학회 2003년도 생물공학의 동향(XII)
• /
• pp.164-168
• /
• 2003

유채유를 사용하여 바이오디젤 생산을 위한 1단 전이에스테르화 공정에 있어서 반응온도 $60^{\circ}C$, 유지에 대한 메탄올 몰비 1:10 이상, 1.0 % (w/w) 포타슘 하이드록시드의 조건에서 98.5% 이상의 전화율을 얻을 수 있었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.514-517
• /
• 2008

Water gas shift(WGS) is an important step in fuel process for fuel cells, and improperness of commercial WGS catalysts for use in fuel cell systems has prompted numerous researches on noble metal catalysts. A selected noble metal catalyst for water gas shift reaction(WGS) was prepared with various metal loadings. The prepared catalysts were tested under two feeding conditions. At moderate residence time, carbon monoxide conversion was much higher on the noble metal catalysts as compared to commercial high-temperature shift catalyst. Effects of metal loading were examined by activity tests at short residence time. Higher metal loading effected higher reaction rate. The kinetic data was fitted to simple reaction equations and effectiveness factor was estimated. The results suggest the necessity of a structural design for the highly active noble metal catalysts.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 하계학술대회 논문집
• /
• pp.504-507
• /
• 1991

Modelling and simulation of booster which is used as step-up DC/DC converter for small scale fuel cell generator is studied. And 2kW booster based on this result is designed. Especially, booster efficiency related with fuel cell and control characteristics are analyzed and a 2kW booster is experimented in various operating condition. As a result, power conversion efficiency is above 74% throughout the whole operating range.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1038-1040
• /
• 1992

Booster is used widely as one of the step-up DC/DC power converter in power conversion process for fuel cell power plant which have the electrical characteristic of the high current density and low cell voltage. In view of control system, booster can be unstable when it is operated in broad operation range because the transfer function of booster has zero in right half plane of s-domain. So for reliable operation, controller must make the system stable in whole working range. In this paper, the two control method such as digital PID control and fuzzy control is studied for booster output voltage regulation in fuel cell plant. The design procedure of PID control and fuzzy control is described. And the experiment of designed controller action is performed in various operation points for controller performance test.

• 한국대기환경학회지
• /
• 제14권4호
• /
• pp.387-392
• /
• 1998

Recently, among after-treatment devices which have high possibility of utility, diesel oxidation catalyst (DOC) is concerned over the world. DOC oxidizes pollutants by means of activate-reaction during by -passing in the catalyst, in doing so, conversion efficiency of PM, CO and HC is high, and this device does not have an effect on engine performance because back pressure is not nearly increased. But, as a small amount of sulfur content in fuel is oxidized, it makes sulfate, which is absorbed on the surface of catalyst. So, in this study, the experiment is carried out by means of using ordinary fuel (0.1wt%) and low sulfur fuel (0.05wt%) with DOC, and the emission gas of diesel engine is measured.

• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.60-69
• /
• 2000

In order to obtain underwater or underground power sources, the closed cycle diesel engine is operated in the non air-breathing circuit system where the major species of the working fluid include oxygen, argon, and recycled exhaust gas. In the present study, the closed cycle diesel engine is designed to operate at the intake pressure between 2 and 3 bar. For operating in the open-cycle and closed-cycle situations, experimental apparatus using this diesel engine is made with ACAP as data acquisition system. In open, semi-open, and closed cycle modes, the predicted p-$\theta$ and P-V are compared with load bank power. Computation have been performed for wide range of major experimental parameters such as the specific fuel and oxygen concentrations, fuel conversion efficiency and polytropic exponent, IMEP and maximum cylinder pressure.