• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2856-2861
• /
• 2008

A catalytic burner has been developed to utilize thermal energy from the fossil fuel without nitrogen oxides (NOx) emission. The burner is shaped into a mat to maximize the heating surface. Premixed combustion has been developed to be used in a closed chamber, such as a radiation type industrial dryer. The burner yields the thermal energy in the form of thermal radiation in the infrared regime, which is proved to be effective to dry organic substances for low moisture condition. Thermal efficiency including the sensible heat is better correlated to the moisture compared to the dry rate.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2916-2921
• /
• 2008

This paper presents the performance and characteristics of small spark-ignited small 2-stroke engine. A single cylinder, two-stroke, air cooled 23cc SI engine for brush-cutter was used in this study. For the performance of the engine, rpm, torque, fuel consumption and lubricate oil consumption were measured, and also HC, CO, NOx emissions and excess air ratio according to throat open ratio under two lubrication method were measured and analyzed. The results showed that maximum of engine rpm is nearly same in both methods and also, torque, power is similar. exhaust emissions tend to decrease with throat open ratio.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.2
• /
• pp.126-130
• /
• 2009

The present study describes an investigation into the characteristics of combustion oscillation and its suppression instability of a silo type gas turbine combustor in commercial power plant. Combustion oscillation is occurred the combustor in near full load during operation. As a result of FFT analysis of the combustion dynamics, the frequency of the oscillation is analyzed as the 1'st longitudinal mode of acoustic resonance of the combustor. For suppress of the instability, combustion tuning with adjust of fuel valve schedule is carried out, which changes equivalent ratio of each burners. As the result, the oscillation is successfully reduced with meeting the level of NOx emission regulation.

• Journal of Environmental Health Sciences
• /
• v.26 no.4
• /
• pp.38-44
• /
• 2000

Compared to other waste, waste tire has much discharge quantity and calorie. When we use waste heat from waste tire, it can be definitely better substitute energy than coal and anthracite in high oil price age. To use as a basic data for providing low cost and highly effective heating system, following conclusion was founded. Annual waste tire production was 19,596 million in 1999, Recycling ratio was almost 55% and more than 8.78 million was stored. Waste tire has lower than 1.5% sulfur contain ratio which is resource of an pollution, So it is a waste fuel which can be combustion based on current exhaust standard value without any extra SOx exclusion materials. Waste tire has 9,256Kcal/kg calorific value and it is higher than waste rubber, waste rubber, waste energy as same as B-C oil. When primary and second air quantity was 1.6, 8.0 Nm$^3$/min, dry gas production time was 270min and total combustion time was 360 min. In the SOx, NOx, HC of air pollution material density were lower than exhaust standard value at the back of cyclone and dusty than exhaust standard value without dust collector.

• Journal of the Korean Society of Combustion
• /
• v.9 no.3
• /
• pp.36-43
• /
• 2004

The flame patterns were investigated in an oscillating combustion burner equipped with a specially designed proportioning valve. The proportioning valve is driven by a solenoid and has an elastomer part which controls the valve opening area. For characterizing the valve, nozzle exit velocities were measured with a hot wire anemometry. The flame patterns were investigated by direct photographing methods using a high speed camera and a digital camera. The results show that the nozzle exit velocities could be controlled diversely and rapidly changed, so the valve seemed appropriate for the oscillating combustion burner application. Mushroom shape and highly wrinkled structure were typical features of the flames in the oscillating combustion burner. As the oscillating intensity of the fuel flow increased, the flame length was shortened.

• Journal of the Korean Society of Combustion
• /
• v.22 no.1
• /
• pp.23-31
• /
• 2017

Large-scale fuel tanks emit massive amount of hardly-combustible VOC mixtures which are light hydrocarbon species in dilution with nitrogen and carbon dioxide. We have developed a lab-scale burner to combust those VOC mixtures by use of a turbulent partially-premixed flame as a pilot flame. For a higher HC treatment ratio, the mixture gases were reformed by a rotating arc plasma device. The results showed that the nitrogen mole fraction and the injecting speed of the VOC mixture influence on the performance of the burner. It was also found that the size of the pilot flame and the power supplied to the plasma device determine the overall HC treatment ratio and the concentrations of CO and NOx in the exhaust gas.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.107-108
• /
• 2013

An experimental study in the dual swirl burner was conducted to analyze the temperature characteristics in the combustion field. The dual swirl burner consists of a main swirling pre-mixed flame with tangential swirler surrounding a pilot which can stabilize a diffusion flame or a partially premixed flame with vane swirler depending on whether fuel is supplied at the exit plane or further upstream. The purpose of this study is to analyse experimentally the characterization of flame temperature in the reacting zone, specially, according to the various combustor diameters like 80mm, 100mm, 130mm and 150mm(O.D). As a result, the temperatures of combustion field were decreased as the diameter of combustor increased. Therefore, these results can be expected that the larger diameter of combustor tend to emit less NOx emission than the small combustor.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.7-14
• /
• 2003

Recently, LPG has been considered as more environmental friendly fuel than liquid fuels for vehicles. However because LPLi engine has the strong point that not only increases the volumetric efficiency and cold startability, but also decreases unburned hydrocarbon exhaust emission in warm-up condition, much attention has moved to development of the Liquid Phase LPG injection (LPLi) system from the mixer type LPG engine. To reduce exhaust NOx, this study investigated the effect of EGR with LPLi engine and determined optimized EGR feeding position and distribution. In addition, engine stability, performance, and exhaust emission level were evaluated.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.5
• /
• pp.784-787
• /
• 2006

Even if EGR is known as a technology which dramatically reduces NOx emission, its application is a quite complicate since it affects fuel economy and increase of PM emission. Therefore, it is a very important issue to investigate an optimal EGR rate considering all engine parameters. This research was numerically conducted to predict combustion and emission characteristics with respect to various EGR rates.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12a
• /
• pp.289-291
• /
• 2011

저온용 Mn-Cu계 촉매의 적정 적용온도를 파악하기 위해 다양한 조건에서 소성하였으며 소성한 촉매를 사용하여 반응온도, 유속 등에 따른 탈질효율 변화를 조사하였다. 실험결과 촉매의 전처리과정에서 바나듐-티타니아계 촉매보다 낮은 일정온도 이상으로 적용시 촉매의 산화가, pore 등에서 변화가 일어나며 궁극적으로 활성저하로 귀결됨을 알 수 있었다.