• Design & Manufacturing
• /
• v.12 no.2
• /
• pp.34-39
• /
• 2018

The biggest topics in the automobile industry are light weightening and fuel efficiency improvement. There's a lot of research going on. It is focused on light weight materials. Light weight material is seen as the best way to reduce fuel consumption and to solve the problem of environmental pollution and resource depletion. For the light weight materials, new materials such as aluminum, magnesium, and carbon-hardening materials can be found. Research on the joining techniques of dual materials, improvement of material properties by improving the method of manufacture of existing materials, and studies on ultra-high strength steel sheets are expected to take up the most weight in lightweight materials. As the strength of the ultra-high strength steel sheets increases during forming, it is difficult to obtain dimensional precision due to the increase in elastic restoring force compared to mild or high strength steel sheets. Spring back is known to be affected by a number of factors due to poor plastic molding, and can be divided into the effects of the material spraying and the process. The study on the plasticitic variables were studied as plasticitic factors that can be controlled by a part company. Tensile testing of ultra-high strength materials was conducted to derive properties for plasticitic analysis and to analyze spring back with two factors controlling the height of the bead and blank holding force by adding tensile force and controlling the flow rate.

• Journal of Biosystems Engineering
• /
• v.39 no.3
• /
• pp.158-165
• /
• 2014

Purpose: The objective of this paper was to compare test standards regarding the performance and safety of agricultural tractors to identify the differences in test conditions, measurement tolerances, and test procedures. Based on the comparison, some recommendations were proposed for possible revisions or improvements to current tractor test standards. Methods: The test standards and codes of major standards development organizations (SDOs), such as the Organization for Economic Cooperation and Development (OECD), the International Organization for Standardization (ISO), the American Society of Agricultural and Biological Engineers (ASABE), EC type approval, and the board of actions of the Nebraska Tractor Test Laboratories (NTTL), were selected and analyzed. Comparison of the test standards: The ISO provides references for fuel and lubricants for tractor tests, and the OECD provides additional measurements for calculating fuel consumption characteristics during the power take-off (PTO) tests. The ISO, EC type approval, and the ASABE provide PTO protective device and the safety requirements. During drawbar power tests, seven transmission ratios are selected for fully automatic transmissions, according to the OECD. In case of hydraulic lift tests, ISO 789-2 and OECD Code 2 advise the use of a static lift force, while SAE J283 advises the use of additional dynamic lift capacity tests for a better representation of in-field operations. The OECD, the ISO, and EC type approval determine the seat index point (SIP), whereas the ASABE determines the seat reference point (SRP) for roll-over protective structure (ROPS) tests. Diversified measurement tolerances were among the braking performance test standards. The European Union (EU) has developed daily limits for vibration exposures with adaptations from ISO 2631-1. Electromagnetic compatibility evaluations are emerging of high-efficiency tractors due to the long-term conformance to electromagnetic emissions and interferences. Comparisons of tractor test standards discussed in this paper are expected to provide useful information for tractor manufacturers and standards development personnel to improve the performance and safety test standards of tractors.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.2 s.257
• /
• pp.188-194
• /
• 2007

New diesel engines equipped with common-rail injection systems and advanced engine management control allow drastic decreases in the production of particulate matters and nitrogen oxides with a significant advantage in terms of the fuel consumption and $CO_2$ emissions. Nevertheless, the contribution of exhaust gas after treatment in the ultra low emission vehicles conception has become unavoidable today. Recently the passive type DPF(Diesel Particulate Filter Trap) system for diesel passenger vehicle has been manufactured into mass production from a French automotive maker since the year of 2000. This passive DPF system fully relies on the catalytic effects from additives blended into the diesel fuel and additives injected into the DPF system. In this study, the effects of PM regeneration in the commercial diesel passenger vehicle with the passive type DPF system were investigated in chassis dynamometer CVS(constant volume sampler)-75 mode. As shown in this experimental results, the DPF regeneration was observed at temperature as low as $350^{\circ}C$. And the engine-controlled the DPF regeneration founded to be one of the most promising regeneration technologies. Moreover, the durability of this DPF system was evaluated with a season weather in terms of the differential pressure and exhaust gas temperature traces from a road test during the total mileage of 80,000km.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.5
• /
• pp.576-582
• /
• 2016

To cope with international regulations, such as Energy Efficiency Design Index (EEDI), Ship Energy Efficiency Management Plan (SEEMP) and so forth, and to enforce limitations on $CO_2$ emissions, green-ship technology to lower fuel consumption has been actively researched, and the development of an energy-saving device (ESD) is being pursued. In order to design an ESD for small and medium-sized domestic vessels, an analysis on flow characteristics has been performed in the present study. Through a model test and numerical analyses, the characteristics of flow around the stern bilge and bulb have been compared to improve wake quality and resistance performance. As a result of these comparisons and analyses, a vertical plate has been adopted,, as a new ESD. Design criteria for the proposed ESD are also suggested. By applying this new ESD, it is expected that the total resistance and average nominal wake can be reduced by 3.04 % and 18.8 %, respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.211-216
• /
• 2015

Large hydraulic excavator weighted 90 tons used the several pumps installed in parallel to use the hydraulic pump driving gearbox to improve fuel consumption by improving the energy efficiency of the hydraulic system. Gearbox connected to hydraulic pump supply the mechanical output to the high pressure and low pressure pump to be supplied by torque and rotation, which are the mechanical power, through a input shaft connected to large size engine of the excavator. So, gearbox connected to hydraulic pump is same as main artery in the human body and is required long life because it operates the hydraulic pump continuously during operating the engine. This study had used oil contamination analysis method to check the wear characteristics of the gearbox and frequency response characteristic analysis method to check the failure of the teeth failures of gearbox, while the test equipment adopted by the electrical feedback method to reduce the energy consumption was operating for the life assessment, in which the required power was 600 kW input power.

• Journal of Energy Engineering
• /
• v.24 no.4
• /
• pp.42-47
• /
• 2015

While the oxygen content of gasoline for automobiles in Korea is regulated to less than 2.3 weight %, European and World-Wide Fuel Charter (WWFC) regulate it to less than 2.7 weight %. The oxygen content of oxygen-containing materials increases the octane number of the fuel due to the secondary combustion in the internal combustion engine. It has been reported to be effective in reducing emissions, such as CO, HC, which is caused by incomplete combustion. Before 2000s in the United States and Europe, there has been many researches about vehicle application of the changes in oxygen content of gasoline. However, there are not many domestic researches which reflect the improvement of the fuel quality and automotive technology. In this study, fuels of three different oxygen contents were applied to GDI and MPI engines. As a result, the changes of fuel consumption and emission gas were very similar depends of the oxygen content changes. The PN in GDI engine was decreased as the oxygen content was increased.

• Food Engineering Progress
• /
• v.13 no.4
• /
• pp.308-313
• /
• 2009

This study was conducted to design and fabricate a heat pump that can produce some weather conditions similar to those of the dry season of the rough rice in Korea, and to investigate basic performances of the apparatus. During the drying test, the amount of energy consumption and drying characteristics were measured at four different temperature levels ranging between 20$^{\circ}C$ and 50${^{\circ}C}$. In the psychrometric chart, the freezing capacity and refrigerant circulation ratio of the heat pump were 173 kJ/kg and 49.6 kg/hr, respectively. Therefore, coefficient of performance was 5.5, which was superior to that of refrigerant R-22 (4.0) in standard refrigeration cycle. In addition, the time to reach target drying temperature (30${^{\circ}C}$) and relative humidity (40%) were 6 minutes and 7 minutes, respectively. Temperature differences between the drying temperature and the rice were 1.5${^{\circ}C}$ and 8.5${^{\circ}C}$ at the drying temperatures of 21.9${^{\circ}C}$ and 48.7${^{\circ}C}$, respectively. This result demonstrated that the increased temperature of the rice in the drying section decreased sufficiently in the tempering section. At the drying temperatures of 21.9, 30.7 38.8, and 48.7${^{\circ}C}$, drying rates were 0.29, 0.61, 0.85, and 1.26%/hr, respectively, which were similar to those of commercial dryer. In addition, the amounts of energy consumption were 325, 667, 692, and 776 kJ/kg, respectively. These results showed that this dryer saved up to 86% of energy consumption compared with the commercial dryer, which uses 4,000-5,000 kJ/kg of fossil fuel.

• Journal of Environmental Impact Assessment
• /
• v.8 no.2
• /
• pp.65-71
• /
• 1999

Characteristics of food garbage discharged from primary schools in Seoul Metropolitan city were analysed from a recycling point of view. The results of study are epitomized as follows : 1. Factors of generation of food garbage are mainly an unbalanced diet habit, indifference of class teachers, and worn-out cooking equipments. 2. Measures of reduction are principally a written message to parents, broadcasting in the school, and instructions. 3. Methods of recycling are mainly feed stuff, composting by school itself, composting on commission, and making feed stuff on commission. 4. Obstacles of food garbage recycling are a nasty smell of composting apparatus, an excessive fuel consumption of composting apparatus, a high concentration of salt, and an unstable demand for feed stuff and compost produced from food garbage. 5. Correlation factors are like follows : the number of feeding children and food garbage weight after cooking is 0.35, total food garbage generated and monthly treatment cost of food garbage is 0.20, individual school lunch expenses and food garbage weight after cooking is -0.10, individual school lunch expenses and food garbage generated per capita is 0.02, and individual school lunch expenses and monthly treatment cost of food garbage is 0.03.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.4
• /
• pp.301-308
• /
• 2006

Today's automobiles are changing into miniaturization and light weight for saving natural resources and energies. In order to raise the sufficiency of fuel consumption, new mechanism and components are required. Therefore, the expectations on the new materials are very high. Especially, Al materials are widely used to reduce the motors weight. Al using in automobiles is mostly casting material, and the material is developing rapidly in step with technical innovation. Al die casting has become an important field, as we are turning today's motor into light weight. One of the parts in steering system, valve housing, plays a role to reduce the operating effort of drivers. If valve housing being a part of steering system is produced by gravity casting, the space that manufacturing equipments are installed will be increased, and more energies and workers will be needed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.244-254
• /
• 2002

To enhance the acceleration performance and fuel consumption rate of a vehicle, the torque converter is modified or newly-developed with reliable analysis model. Up to recently, the one dimensional performance model has been used for the analysis and design of torque converter. The model is described with constant parameters based on the concept of mean flow path. When it is used in practice, some experiential correction factors are needed to minimize tole estimated error. These factors have poor physical meaning and cannot be applied confidently to the other specification of torque converter. In this study, the detail dynamic model of torque converter is presented to establish the physical meaning of correction factors. To verify the validity of model, performance test was carried out with various input speed and oil temperature. The effect of oil temperature on the performance is analysed, and it is applied to the dynamic model. And, to obtain the internal flow pattern of torque converter, CFD(Computational Fluid Dyanmics) analysis is carried out on three-dimensional turbulent flow. Correction factors are determined from the internal flow pattern, and their variation is presented with the speed ratio of torque converter. Finally, the sensitivity of correction factors to the speed ratio is studied for the case of changing capacity factor with maintaining torque ratio.