• 조명전기설비학회논문지
• /
• 제26권9호
• /
• pp.33-39
• /
• 2012

For photovoltaic power generation need certainly decreasing module's price and increasing promote efficiency technology. Almost of solar panel is on the decrease energy efficiency since 2,000. like silicone(Si) solar panel, thin film solar panel and etc. Silicone(Si) solar panel was best efficiency in 1999. It's 24%. But after that time, It didn't pass limit of energy efficiency. That's why, nowadays being issued that using III-V compound semiconductor to high efficiency of concentrating photovoltaic system for making an alternative proposal. In Korea, making researches in allied technology with III-V compound semiconductor solar panel, condenser technology, and solar tracker. but feasibility study for concentrating photovoltaic power generation hasn't progressed yet. This thesis made a plan about CPV(Concentrating Photovoltaic)system and CPV has a higher energy efficiency than PV(Photovoltaic)system in fine climate conditions from comparing CPV with using silicone(Si) solar panel to PV's efficiency test result.

• 한국전기전자재료학회논문지
• /
• 제25권9호
• /
• pp.743-749
• /
• 2012

In this paper, we designed and fabricated LED navigation lights which can replace the existing ones immediately and overcome disadvantages due to use of conventional lamps. To decide the best arrangement and position of a LED module, optical systems of existing navigation lights were analyzed and refracted routes of rays were simulated. The electrical and optical characteristics of the fabricated LED navigation lights were measured and analyzed with a goniophotometer. To calculate ranges of visibility, the vertical and horizontal luminous intensity distributions were evaluated in accordance with the COLREGs (convention on the international regulation for preventing collisions at Sea). From the results, the proposed LED navigation lights showed suitable characteristics for marine environment with the power consumption reduced by 90% and the maximum luminous intensity increased by 20% compared to the existing navigation lights.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.1080-1081
• /
• 2015

CPV system in the desert areas or areas near the equator, as is suitable for high-temperature region. As compared to silicon solar cells, CPV system have a high proportion of a BOS (balance of system). Solar cells because of its low proportion when designing a module technology is applied in a variety of ways. Applied to the CPV system is classified into two kinds of optical technology. One of those using fresnel lens uses refraction of light energy. The other is a mirror reflection of the structure using sprays. Both of these two ways to condense the sun to collect solar cell is a form of light. And goals by using a small solar cell materials is to produce more energy. This research proposes rational design approach to calculate proper system capacity in consideration of the aforementioned factors in CPV system.

• 대한기계학회논문집A
• /
• 제28권3호
• /
• pp.245-250
• /
• 2004

This paper proposes a new method of measuring an air interface distance between a solid immersion lens(SIL) applied magneto-optic technology and the disk surface. For applying near-field recording (NFR) technology to the magneto-optic storage devices for the next generation, it is positively necessary to maintain the small air gap under about 100㎚. We design an apparatus that consists of some optical components such as a prism, a polarizer and an analyzer. By using the Fresnel reflection coefficient equation, Jones matrices calculation and Malus's law, we establish a mathematical model for understanding the characteristics of the system. The simulations are based on the mathematical model and through the simulation results which is made with various cases we can estimate the performance of the new optical gap sensor system. Experimental results, which are also based on the mathematical model for specific cases, are in good agreement with simulated ones and demonstrate the possibility as the new optical gap sensor.

• 한국정밀공학회지
• /
• 제23권5호
• /
• pp.190-196
• /
• 2006

Transparent materials are widely used in the fields of optic parts and bio industry. We have experiment to find out the characteristics of the micromachining inside transparent materials using femtosecond laser pulses. With its non-linear effects by very high peak intensity, filament (plasma channel) was formed by the cause of the self-focusing and the self-defocusing. Physical damage could be found when the intensity is high enough to give rise to the thermal stress or evaporation. At the vicinity of the power which makes the visible damage or modification, the structural modification occurs with the slow scanning speed. According to the polarization direction to the scanning direction, the filament quality is quite different. There is a good quality when the polarization direction is parallel to the scanning direction. For fine filament, we could suggest the conditions of the high numerical aperture lens, the short shift of focusing point, the low scanning speed and the low power below 20 mW. As the examples of optics parts, we fabricated the fresnel zone plate with the $225{\mu}m$ diameter and Y-bend optical wave guide with the $5{\mu}m$ width.

• 한국태양에너지학회 논문집
• /
• 제33권2호
• /
• pp.56-63
• /
• 2013

Daylighting system is an alternative lighting system using daylight collecting device, light transformer and light diffuser. In this paper, we developed a daylighting system in which the collecting device composed by dual parabolic reflectors, the silica optical fiber adapted to the light transformer and light diffuser made of the polyglass square sheet. We have estimated the system efficiency and general color rendering index(Ra) of the developed system. The system efficiency measured to 23.8% and Ra was revealed as 95. Ra number of the developed system is bigger than the number(65) of the previous fresnel lens based sunlight collector.

• Journal of the Optical Society of Korea
• /
• 제16권3호
• /
• pp.247-255
• /
• 2012

Daylighting has a very effective role in reducing power consumption and improving indoor environments in office buildings. Previously, it was not under consideration as a major source of renewable energy due to poor reliability in the design. Optical fiber as a transmission medium in the daylighting system demands uniform distribution of light to solve cost, heat, and efficiency issues. Therefore, this study focuses on the uniform distribution of sunlight through the fiber bundle and to the interior of the building. To this end, two efficient approaches for the fiber-based daylighting system are presented. The first approach consists of a parabolic mirror, and the second approach contains a Fresnel lens. Sunlight is captured, guided, and distributed through the concentrator, optical fibers, and lenses, respectively. At the capturing stage, uniform illumination solves the heat problem, which has critical importance in making the system cost-effective by introducing plastic optical fibers. The efficiency of the system is increased by collimated light, which helps to insert maximum light into the optical fibers. Furthermore, we find that the hybrid system of combining sunlight and light emitting diode light gives better illumination levels than that of traditional lighting systems. Simulation and experimental results have shown that the efficiency of the system is better than previous fiber-based daylighting systems.

• 한국분무공학회지
• /
• 제26권4호
• /
• pp.212-218
• /
• 2021

The present study aims to develop the Surface Plasmon Resonance (SPR) imaging system facilitating the real-time measurement of the concentration of evaporating binary mixture droplet (BMD). We introduce the theoretical background of the SPR imaging technique and its methodology for concentration measurement. The SPR imaging system established in the present study consists of a LED light source, a polarizer, a lens, and a band pass filter for the collimated light of a 589 nm wavelength, and a CCD camera. Based on the Fresnel multiple-layer reflection theory, SPR imaging can capture the change of refractive index of evaporating BMD. For example, the present study exhibits the visualization process of ethylene glycol (EG)-water (W) BMD and measures real-time concentration change. Since the water component is more volatile than the ethylene glycol component, the refractive index of EG-W BMD varies with its mixture composition during BMD evaporation. We successfully measured the ethylene glycol concentration within the evaporating BMD by using SPR imaging.

• 한국광학회지
• /
• 제18권4호
• /
• pp.246-255
• /
• 2007

부양영상시스템은 광학계를 통하여 입력영상 또는 물체의 상을 표시소자의 최종면으로부터 떨어진 특정 공간 내에 재생하는 장치이다. 재생된 입력영상은 표시소자와 관찰자 사이의 공간상에 위치하며 관찰자에게 가상의 입체효과를 제공한다. 입체부양영상시스템은 입체영상 및 입체상을 입력영상으로 하여 재생된 부양영상 내에 돌출 및 후퇴방향의 입체효과를 부과하여 기존의 입체영상 표시소자보다 효과적인 깊이감을 제공한다. 일반적으로 입체영상으로 쓰이는 입력영상의 크기 및 시차량은 광학계를 통하지 않는 입체영상 표시소자에 최적화되어 있다. 따라서 광학계를 통하여 입체상을 재생할 경우, 관찰자에게 재생된 입력영상의 크기 및 시차량은 광학계의 최종배율에 따라 축소 또는 확대된다. 그러나 관찰자와 디스플레이의 최종 면 사이의 관찰거리는 불변이므로 광학계를 통하여 재생된 입체부양영상은 관찰자에게 최종배율과 다른 깊이감을 제공한다. 본 논문은 삼중 프렌넬 렌즈로 이루어진 광학계에서 입체부양영상용 입력영상의 시차량을 광학계의 최종배율에 비례하도록 보정하고, 관찰자에게 올바른 깊이감을 제공하는 방법 및 결과를 제시하였다. 이 광학계는 부양영상의 부양 심도 및 영상의 질 향상을 위하여 사용되었고, 입력영상으로는 19인치 무안경식 입체영상 표시소자를 통하여 재생된 입체영상이 사용되었다.

• 한국항공우주학회지
• /
• 제44권2호
• /
• pp.156-164
• /
• 2016

우주기반기술 검증용 극초소형 위성 STEP Cube Lab.(Cube Laboratory for Space Technology Experimental Project)의 주요 탑재체인 집광형 프레넬렌즈가 적용된 고효율 집광형 태양전력시스템, 열선 절단방식이 적용된 무충격 구속분리장치 그리고 MEMS 기반의 고체추력기에 대해 인증수준의 열진공 시험과 열평형 시험을 수행하였다. 이를 통해 열진공 환경 하의 인증수준의 시험온도규격에서 탑재체의 구조건전성 및 정상작동성을 검증하고, 열평형 시험 결과로부터 보다 신뢰성 높은 보정된 열해석 모델을 확립하였다. 본 논문에서는 주요 임무 탑재체의 인증수준의 열환경 시험에 대한 기능시험 결과 및 시험 결과로부터 수행된 열모델 보정과 최종 열모델의 궤도 열해석 결과에 대해 기술하였다.