• ETRI Journal
• /
• v.46 no.2
• /
• pp.227-237
• /
• 2024

This study proposes a novel, conditionally applied neural network technique to reduce the overall peak-to-average power ratio (PAPR) of an orthogonal frequency division multiplexing (OFDM) system while maintaining an acceptable bit error rate (BER) level. The main purpose of the proposed scheme is to adjust only those subcarriers whose peaks exceed a given threshold. In this respect, the developed C-ANN algorithm suppresses only the peaks of the targeted subcarriers by slightly shifting the locations of their corresponding frequency samples without affecting their phase orientations. In turn, this achieves a reasonable system performance by sustaining a tolerable BER. For practical reasons and to cover a wide range of application scenarios, the threshold for the subcarrier peaks was chosen to be proportional to the saturation level of the nonlinear power amplifier used to pass the generated OFDM blocks. Consequently, the optimal values of the factor controlling the peak threshold were obtained that satisfy both reasonable PAPR reduction and acceptable BER levels. Furthermore, the proposed system does not require a recovery process at the receiver, thus making the computational process less complex. The simulation results show that the proposed system model performed satisfactorily, attaining both low PAPR and BER for specific application settings using comparatively fewer computations.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.4
• /
• pp.461-466
• /
• 2020

There are many application fields of electrical energy storage such as load shifting, integration with renewables, frequency or voltage supports, and so on. Especially, the frequency regulation is needed to stabilize the electric power system, and there have to be more than 1 GW as power reserve in Korea. Ni-rich layered oxide cathode materials have been investigated as a cathode material for Li-ion batteries because of their higher discharge capacity and lower cost than lithium cobalt oxide. Nonetheless, most of them have been investigated using small coin cells, and therefore, there is a limit to understand the deterioration mode of Ni-rich layered oxides in commercial high energy Li-ion batteries. In this paper, the pouch-type 20 Ah-scale Li-ion full cells are fabricated using Ni-rich layered oxides as a cathode and graphite as an anode. Above all, two test conditions for the application of frequency regulation were established in order to examine the performances of cells. Then, the electrochemical performances of two types of Ni-rich layered oxides are compared, and the long-term performance and degradation mode of the cell using cathode material with high nickel contents among them were investigated in the frequency regulation conditions.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.3
• /
• pp.116-126
• /
• 1993

The finite element method(FEM) has been commonly used for structural dynamic analysis. However, the direct global application of FEM to large complex structures such as ships and offshore structures requires considerable computational efforts, and remarkably more in structural dynamic optimization problems. Adoption of the component-mode synthesis method is an efficient means to overcome the above difficulty. Among three classes of the component-mode synthesis method, the free-interface mode method is recognized to have the advantages of better computational efficiency and easier implementation of substructures' experimental results, but the disadvantage of lower accuracy in analytical results. In this paper, an advanced method to improve the accuracy in the application of the free-interface mode method for the vibration analysis of large complex structures is presented. In order to compensate the truncation effect of the higher modes of substructures in the synthesis process, both residual inertia and stiffness effects are taken into account and a frequency shifting technique is introduced in the formulation of the residual compliance of substructures. The introduction of the frequency shrift ins not only excludes cumbersome manipulation of singular matrices for semi-definite substructural systems but gives more accurate results around the specified shifting frequency. Numerical examples of typical structural models including a ship-like two dimensional finite element model show that the analysis results based on the presented method are well competitive in accuracy with those obtained by the direst global FEM analysis for the frequencies which are lower than the highest one employed in the synthesis with remarkably higher computational efficiency and that the presented method is more efficient and accurate than the fixed-interface mode method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.431-434
• /
• 2005

Generally, noise in a reciprocating compressor is attributed to the driving force of a pump. However, close examination shows that the noise heard by customers finally results from radiation of a shell in a compressor, the noise caused by both transmission through a shell and resonance with the natural frequency of a shell. Therefore, the peak frequencies contributing to the overall level of a compressor' noise are closely concerned with vibration of a shell. That's why radiated noise by vibration can be reduced by changing the mode of a shell and by shifting the peak frequencies to other ranges, which are not globally related with the overall noise level. In this paper, the main peak frequencies are analyzed to reduce the radiated noise of a shell, and the vibration characteristics of a shell are examined through Frequency Response Function and Finite Element Analysis. Moreover, the Operational Deflection Shape for a shell is measured with consideration of real driving force of a pump. Finally, the optimum position on a shell, closely related to the main peak frequencies, is found, and the overall noise level caused by radiated noise of a shell is noticeably reduced by mass or stiffness modification of the position.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.319-322
• /
• 2007

In the development of paralleling techniques, Multi-Phase Interleaved(MPI) converter constitutes one of the most promising alternatives reported in the last years. This technique consists of a phase shifting of the control signals of several cells in parallel operating at the same switching frequency. As a result, the aggregated input and output current waveform exhibit lower ripple amplitude and smaller harmonics content than in synchronous or stochastic operation modes. Based on the inherent advantages of the MPI converter, in this paper, a control scheme, which can reduce current and voltage rifle, is proposed for PEMFC generation systems. The MPI boost converter is composed of several identical boost converters connected in parallel.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.12
• /
• pp.2002-2008
• /
• 2001

Nonlinear vibration characteristics of a piezoelectric-type micro actuator used for hard disk drives are experimentally studied. The nonlinear characterisitics include hysteresis, superharmonic resonance, jump phenomenon, and shifting of natural frequencies. The vibration modes and frequencies of the commercial actuator of the Hutchinson's Magnum series are measured using a laser vibrometer. From harmonic excitation to the PZT acturator, we observe interesting hysteresis patterns with 3 times input frequency. It is shown that the micro actuator has the typical 3 times superhamonic resonances coupled to the first torsional and sway modes of the suspension.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.5
• /
• pp.445-450
• /
• 2002

We analyzed and measured a CPW(coplanar waveguide)-to-microstrip right-angled transition. Asymmetric CPW-to-microstrip transitions show significant resonances by the slot mode generation at the discontinuities. The air-bridge just shifting the resonance frequency can not fundamentally suppress the occurrence of the slot mode. So, we proposed the structure using offset microstrip section to eliminate the resonance. The proposed structure may be useful for the application of multi-layed structure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.81-82
• /
• 2014

Recently it is often reported about toxic nanomaterials to organisms. In other words, it is called nanotoxicity, toxic nanomaterials have extremely toxic properties. Zinc oxide is widely used as a promising nanomaterials, but some researchers are warning that nanotype zinc oxide has nanotoxicity. One of typical zinc oxide materials is a zinc oxide nanowire, especially, there is no technique which is detecting a zinc oxide nanowire because of its geometric. In here, we use reduced graphene oxide in order to detect zinc oxide nanowire and use DNA immobilized cantilever sensor, we detect graphene wrapped zinc oxide nanowire. Detection of a zinc oxide nanowire is measured by shifting of cantilever's resonance frequency based on vibration theory. It is proved that cantilever sensor is valid for nanomaterial detection. We showed that detection of a zinc oxide nanowire is successful.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.165-166
• /
• 2008

Bistatic spotlight synthetic aperture radar(BSSAR) with single track configuration uses the transmitter and the receiver which travel along the single track such as the leader-follower. For the BSSAR imaging, we modify the range migration algorithm. In time domain, we make the monostatic SAR using shifting of path, Then, in frequency domain, we compensate the separated distance between the scene center and the flight path using the principle of the stationary phase (PSP).

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.2
• /
• pp.94-97
• /
• 2007

The desin and implementation of a CMOS analog integrated circuit that provides dual-mode modulations, PWM for active clamp reset converter and PFM for LLC resonant converter, is described. The proposed controller is capable of implementing programmable soft start and current-mode control with compensating ramp for PWM and frequency shifting soft start for PFM. Also it provides delay time for both modes. PWM mode is implemented by active clamp reset converter and PFM mode is implemented by LLC resonant convereter, respectively. The chip is fabricated using the 0.6um high voltage CMOS process.