• 대한기계학회논문집
• /
• 제13권3호
• /
• pp.461-471
• /
• 1989

본 연구에서는 혼합 모우드 균열문제의 연구를 위하여 .KAPPA.$_{II}$ /.KAPPA.S1I\ulcorner조절이 간편하고, 균열진전경로가 하중방향에 따른 균일전면의 자유표면의 영향을 균일하게 한 시험편(이하 RCM 또는 round compact mixed-mode 시험편이라 한다)을 고안하여 균열길이 및 하중작용 방향에 따른 .KAPPA.$_{I}$ 및 .KAPPA.S1II를 수치해석한 다음 일반화 하였다. 또 고강도와 용접성이 요구되는 항공기부품, 압력용기, 지상운송차량 등에 사용되고 있는 5083-H115 알루미늄 합금에 대해 혼합 모우드 균열진전 방향 및 피로균열 진전특성을 분석하고자 한다.다.

• 콘크리트학회지
• /
• 제8권6호
• /
• pp.223-234
• /
• 1996

본 논문에서는 단조증가하중을 받는 철근 및 프리스트레스트 콘크리트 슬래브의 비선형거동, 즉 탄성, 비탄성, 극한영역에 이르기까지의 모든 하중이력에 대한 응력-변형도 관계와 균열의 진행 및 철근 및 텐던과 콘트리트의 응력과 변형도 등을 정확히 해석할 수 잇는 해석법의 제시를 목적으로 한다. 이러한 목적을 위하여 본 연구에서는 재료적 및 기하학적 비선형성을 고려하였다. 기하학적 비선형성은 Von Karman의 가정에 기본을 둔 total Lagrangian formulation에 의해 고려하였으며 재료적 비선형성에 대해서는 균열콘크리트에대한 인장, 압축, 전단모델과 콘크리트 중에 있는 철근 및 텐던모델을 조합하여 고려하였다. 이에 대한 콘크리트의 균열모델로서는 분산균열모델을 사용하였으며, 철근 및 텐던에 대해서는 1축 응력상태로 가정하여 등가의 분산분포된 철근 및 텐던층으로 모델화하였다. 본 논문에서 제안한 해석방법의 타당성을 검증하기 위하여 몇 개의 실험치를 해석치와 비교.검토한 결과, 본 논문의 해석방법에 의하면 철근 및 프리스트레스트 콘크리트 슬래브의 비선형거동을 보다 정확하게 예측할 수 있었다.

• Transactions on Electrical and Electronic Materials
• /
• 제12권1호
• /
• pp.24-27
• /
• 2011

Effect of substitution of Mn for Ni on transformation behavior, shape memory characteristics and superelasticity of Ti45Ni-5Cu alloy has been investigated by means of electrical resistivity measurements, X-ray diffraction, thermal cycling tests under constant load and tensile tests. The one-stage B2-B19' transformation occurred when Mn content was 0.5 at%, above which the two-stage B2-B19-B19' transformation occurred. A temperature range where the B19 martensite exists was expanded with increasing Mn content because decreasing rate of Ms (60 K / % Mn) was larger than that of Ms' (40 K / % Mn). Ti-(45-x)Ni-5Cu-xMn alloys were deformed in plastic manner with a fracture strain of 60 % ~ 32 % depending on Mn content. Clear superelasticity was found in fully annealed Ti-(45-x)Ni-5Cu-xMn alloys with Mn content more than 1.0 at%, which was ascribe to a solid solution hardening by substitution of Mn for Ni.

• Transactions on Electrical and Electronic Materials
• /
• 제12권1호
• /
• pp.28-31
• /
• 2011

Transformation behavior and shape memory characteristics of Ti-(45-x)Ni-5Cu-xCr (x=0.5-2.0) alloys have been investigated by means of electrical resistivity measurements, differential scanning calorimetry, X-ray diffraction and thermal cycling tests under constant load. Two-stage B2-B19-B19' transformation occurred in Ti-(45-x)Ni-5Cu-xCr alloys. The B2-B19 transformation was separated clearly from the B19-B19' transformation in Ti-44.0Ni-5Cu-1.0Cr and Ti-43.5Ni-5Cu-1.5Cr alloys. A temperature range where the B19 martensite exists was expanded with increasing Cr content because decreasing rate of Ms (85 K / % Cr) was larger than that of Ms' (17 K / % Cr). Ti-(45-x)Ni-5Cu-xCr alloys were deformed in plastic manner with a fracture strain of 68% ~ 43% depending on Cr content. Substitution of Cr for Ni improves the critical stress for slip deformation in a Ti-45Ni-5Cu alloy due to solid solution hardening.

• Restorative Dentistry and Endodontics
• /
• 제5권1호
• /
• pp.41-46
• /
• 1979

Silver amalgam has superior mechanical and physical properties, therefore it has been widely used in dental clinics. But we have found the silver amalgam failures frequently, its important reasons are fracture, fallen-out, tarnish, corosion and secondary caries etc. The author studied the compressive strength of silver amalgam. The author made the standardized specimen, prepared the Black's Class II cavity on chromecobalt alloy, and placed the three types of Unitek$^{(R)}$ pin (Type of pins are straight type, "ㄱ" bent type, "$\sqcap$" bent type pin. The compressive strength was measured by (Dynamic Strain Meter Shinko Co. Japan). The author took the following results by comparing with the control group, not used pin. 1) Compressive force of silver amalgam in straight type pin was $187.11{\pm}39.00kg$, $252.98{\pm}31.91kg$ in "ㄱ" type bent pin, $189.00{\pm}37.46Kg$ in "$\sqcap$" type bent pin, $172.33{\pm}28.07Kg$ in the control group. 2) The statistic significance of the compressive strnegth between each group showed that "ㄱ" type, bent pin is stronger than the control group or straight type pin. 3) There were no difference of significances between the control group and straight type pin, control group and "ㄱ" type bent pin and "$\sqap$" type bent pin, "ㄱ" type' bent pin "$\sqcap$" and type bent pin.

• 한국지진공학회논문집
• /
• 제6권4호
• /
• pp.31-37
• /
• 2002

최근에 용접 수평헌치로 보강된 내진 철골 모멘트 적합부의 응력 전달모형 및 설계법이 Lee-Uang에 의해 새로이 제안된 바가 있다. 본 연구에서는 반복재하 실물대 실험을 통하여 이 설계방안의 타당성을 실험적으로 확인하고 응력집중에서 기인하는 헌치단부의 균열을 방지할 수 있는 효과적인 상세도 제안하고자 하였다. Lee-Uang의 방안에 의해 설계된 3개의 시험체는 모두 설계의도에 부합되게, 헌치단부의 외측에서 형성된 소성힌지에서 0.04 radian에 달하는 뛰어난 소성회전능력을 발휘하였다. 도한 헌치단부에 구배를 주고 처공하거나 또는 보 웨브 스티프너를 헌치의 웨브로 부분적으로 또는 완전히 연장하는 상세에 의해 헌치단부의 균열발생을 효과적으로 방지할 수 있음을 실험적으로 입증하였다. 아울러 해석적으로 예견되었던 헌치 웨브의 스트럿 거동도 스트레인 계측을 통하여 실험적으로 입증하였다.

• 대한금속재료학회지
• /
• 제47권8호
• /
• pp.500-507
• /
• 2009

Pb-free solder has recently been used in electronics in efforts to meet environmental regulations, and a number of Pb-free solder alloy choices beyond the near-eutectic SnAgCu solder are now available. With increased demand for thin and portable electronics, the high cost of alloys containing significant amounts of silver and their poor mechanical shock performance have spurred the development of low Ag SnAgCu solder, which provides improved mechanical performance at a reasonable cost. Although low Ag SnAgCu solder exhibits significantly higher fracture resistance under high-strain rates, little thermal fatigue data exist for this solder. Therefore, it is necessary to investigate thermal fatigue reliability of low Ag SnAgCu solder under variation of thermal stress in order to allow its implementation in electronic products with high reliability requirements. In this study, the reliability of Sn0.3Ag0.7Cu(SAC0307), a low Ag solder alloy, is discussed and compared with that of Sn3Ag0.5Cu(SAC305). Three sample types and six samples size are evaluated. Mechanical properties and microstructure of the solder joint are investigated under thermal shock cycles. It was observed that the mechanical strength of SAC0307 dropped slightly with thermal cycling relative to that of SAC305. This reveals that the failure mode of SAC0307 is different from that SAC305 under this critical condition.

• Geomechanics and Engineering
• /
• 제19권2호
• /
• pp.167-178
• /
• 2019

Open-pit (OP) and underground (UG) mining are usually used to exploit shallow and deep ore deposits, respectively. When mine deposit starts from shallow subsurface and extends to a great depth, sequential use of OP and UG mining is an efficient and economical way to maintain mining productivity. However, a transition from OP to UG mining could induce significant rock movements that cause the slope instability of the open pit. Based on Yanqianshan Iron Mine, which was in the transition from OP to UG mining, a large-scale two-dimensional (2D) model test was built according to the similar theory. Thereafter, the UG mining was carried out to mimic the process of transition from OP to UG mining to disclose the triggered rock movement as well as to assess the associated slope instability. By jointly using three-dimensional (3D) laser scanning, distributed fiber optics, and digital photogrammetry measurement, the deformations, movements and strains of the rock slope during mining were monitored. The obtained data showed that the transition from OP to UG mining led to significant slope movements and deformations that can trigger catastrophic slope failure. The progressive movement of the slope could be divided into three stages: onset of micro-fracture, propagation of tensile cracks, and the overturning and/or sliding of slopes. The failure mode depended on the orientation of structural joints of the rock mass as well as the formation of tension cracks. This study also proved that these non-contact monitoring technologies were valid methods to acquire the interior strain and external deformation with high precision.

• 화약ㆍ발파
• /
• 제37권1호
• /
• pp.14-23
• /
• 2019

암석이나 콘크리트와 같은 취성재료의 경우에는 역학적 강도의 하중속도 의존성을 보임에 따라 발파 및 충격해석에 있어 이를 반영코자 하는 노력이 증가하고 있다. 이와 같은 암석의 동적강도의 경우에는 순간적으로 높은 하중이 작용하는 동적하중의 가압특성에 따라 시험편 내의 응력평형상태를 고려한 평가가 수행되어야함이 제안된 바 있다. 본 연구에서는 스플릿 홉킨슨 압력봉 장비를 이용한 포천 화강암의 동적일축압축강도 실험을 통해 응력평형조건의 충족 유무에 따른 암석의 동적파괴과정 및 역학적 강도특성에 대해 고찰하였다. 연구결과 적절한 응력평형상태가 이루어지진 않은 상태에서 평가된 암석의 동적일축압축강도는 상대적으로 과소평가되는 것으로 나타났으며, 이는 하중의 가압면에서 발생하는 조기파괴에 따른 에너지 파괴에너지 손실 및 변형률속도 과대평가에 의한 것으로 판단되었다. 결론적으로 합리적인 동적강도 평가를 위해서는 암석의 변형거동특성에 대한 분석 및 파괴패턴에 대한 검토를 통한 응력평형조건의 세밀한 검증이 수반되어야 할 것으로 판단하였다.

• Structural Engineering and Mechanics
• /
• 제68권6호
• /
• pp.747-760
• /
• 2018

In the present study, a methodology for developing fragilities of arch concrete dams to assess their performance against seismic hazards is introduced. Firstly, the probability risk and fragility curves are presented, followed by implementation and representation of the way this method is used. Amirkabir arch concrete dam was subjected to non-linear dynamic analyses. A modified three dimensional rotating smeared crack model was used to take the nonlinear behavior of mass concrete into account. The proposed model considers major characteristics of mass concrete. These characteristics are pre-softening behavior, softening initiation criteria, fracture energy conservation, suitable damping mechanism and strain rate effect. In the present analysis, complete fluid-structure interaction is included to account for appropriate fluid compressibility and absorptive reservoir boundary conditions. In this study, the Amirkabir arch concrete dam is subjected to a set of 8 three-component earthquakes each scaled to 10 increasing intensity levels. Using proposed nonlinear smeared crack model, nonlinear analysis is performed where the structure is subjected to a large set of scaled and un-scaled ground motions and the maximum responses are extracted for each one and plotted. Based on the results, fragility curves were plotted according to various and possible damages indexes. Discrete damage probabilities were calculated using statistical methods for each considered performance level and incremental nonlinear analysis. Then, fragility curves were constructed based on the lognormal distribution assumption. Two damage indexes were introduced and compared to one another. The results indicate that the dam has a proper stability under earthquake conditions at MCE level. Moreover, displacement damages index is more conservative and impractical in the fragility analysis than tensional damage index.