• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.137-145
• /
• 2008

In this paper, novel CMOS charge pump having NMOS and PMOS transfer switches and a bulk-pumping circuit has been proposed. The NMOS and PMOS transfer switches allow the charge pump to improve the current-driving capability at the output. The bulk-pumping circuit effectively solves the bulk forward problem of the charge pump. To verify the effectiveness, the proposed charge pump was designed using a 80-nm CMOS process. The comparison results indicate that the proposed charge pump enhances the current-driving capability by more than 47% with pumping speed improved by 9%, as compared to conventional charge pumps having either NMOS or PMOS transfer switch. They also indicate that the charge pump reduces the worst-case forward bias of p-type bulk by more than 24%, effectively solving the forward current problem.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.11
• /
• pp.74-79
• /
• 2005

Computational studies on the hydrodynamic behavior of the forward-sweep inducers for the rocket-engine turbopump are presented in comparison with the conventional backward- sweep inducers. In the present study, two kinds of forward-sweep inducers are designed and numerically investigated. Forward-sweep inducers have bigger tip solidity compared to backward-sweep inducers even with shorter axial length due to their forward-sweep leading edge profiles. It is shown that back flows at the inlet decreases dramatically for forward- sweep inducers. And the low pressure region at the back flow are also decreased, which is assumed to promote the suction performance of the inducers. It seems that the hub located upstream of the tip at the leading edge induces pre whirl at the inlet blade tip for the backward sweep inducer. And this pre whirl leads to the big back flow.

• Journal of the Korean Society of Physical Medicine
• /
• v.13 no.3
• /
• pp.121-132
• /
• 2018

PURPOSE: This study was conducted to investigate the effects of type of exercise on neck disability, pain, and postural changes in subjects with forward head posture. METHODS: Two independent researchers conducted a search using KISS, RISS, DBpia (domestic), PubMed, OVID, and Science Direct (overseas) databases. We selected randomized controlled clinical trials by searching using the terms "forward head posture", "exercise therapy", and "therapeutic exercise". Studies published from 2007 to December 2017 were included. PEDro Scale was used to evaluate the quality of the selected studies, and meta-analysis was conducted using the CMA program. This review was registered at PROSPERO (CRD42018068633). RESULTS: Of the total 13768 studies searched, 17 were selected. Positive effects on neck disability were achieved with the base and biomechanical elements (ES=1.63, 95% confidence interval [CI] .49 to 2.75) as well as base, modulator, and biomechanical elements (ES=1.50, 95% [CI] .69 to 2.30). Neck pain improved with the base, modulator, and biomechanical elements (ES=1.96, 95% [CI] 1.08 to 2.82), while postural changes improved with biomechanical elements (ES=1.45, 95% [CI] .64 to 2.25). Additionally, type of exercise had a positive effect. CONCLUSION: The most effective exercises for neck disability are of the base and biomechanical elements, while the most effective types for neck pain are of the base, modulator, and biomechanical elements and the most effective exercise for posture is of biomechanical elements. Combined exercises targeting biomechanical elements were effective at treating disability, pain, and postural changes.

• Journal of Fashion Business
• /
• v.11 no.1
• /
• pp.61-74
• /
• 2007

Photographic measurement was first made with the subjects of 190 males in their 20s residing in the Ningbo area, Zhejiang Province in China. In this second report, lower body shapes were classified and discriminated by using indirect measurement, measurement items, and lower body analysis. The following sums up the research: 1. The subjects were $8.85^{\circ}$ (hip breadth angle), $1.58^{\circ}$ (abdomen upper angle), $11.80^{\circ}$ (hip upper angle), and $5.12^{\circ}$ (lateral lower body posture angle). 2. The subjects of Chinese males in their 20s showed three types of lower bodies: Bow Legs & Slight Slant of Lateral Lower Body Type (30.5%)-gap between legs, curve waist-hip contour, average abdomen-hip profile, and lateral lower body posture were slightly slanted forward. Adjacent Straight Legs & Slight Slant of Lateral Lower Body Type (35.8%)-adjacent straight between legs, curve waist-hip contour, slim abdomen-hip profile, and lateral lower body posture were slightly slanted forward. Balance Legs & Large Slant of Lateral Lower Body Type (33.7%)-average between legs, straight waist-hip contour, protruding hip profile, and lateral lower body posture were largely slanted forward. 3. Eight useful variables for the categorization of the subjects' lower body types were chosen through stepwise discriminant analysis, and the hit ratio of discrimination was 97.9%.

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.5
• /
• pp.44-53
• /
• 1993

In this paper, we discuss on the control algorithm to make the wheeled inverse pendulum type mobile robot move in two dimensional plane. The robot considered in this paper has two independently driven wheels in same axel which suport and move it-self, and is assumed to have the fyro type sensor to know the inclination algle of the body and rotary encoders to know wheel's rotation angular velocity. The control algorithm is divided into three parts. The first part is for the posture and velocity control for forward-backward direction, the second is the steering control, and the last part is for the control of total system to track the given trajectory. We handle the running velocity control of the robot as part of the posture control to keep the balance because the posture relates deeply with the velocity and can be controlled by the velocities of the wheels. The control problem is analyzed as the tracking control, and the controller is realized with the state feedback and feed-forward of the reference velocity. Constructing the control system which contained one intergrator in forward path, we also realized the control system without observer for the estimation of the accumulated errors in the inclination angle of the body. To prevent the robot from being unstable state by sudden variation of the reference velocity when it starts and stops, or changes velocity, the reference velocity of which acceleration is slowly changing, is ordered to the robot. To control its steering, we give the different reference velocities for both wheels which are calculated from the desired angular velocity of the body. Finally, we presents the experimental results of the experimental robot Yamabico Kurara in which the proposed control algorithm had been implemented.

• Journal of Power Electronics
• /
• v.14 no.5
• /
• pp.1047-1056
• /
• 2014

In most grid-connected inverters (GCI) with an LCL filter, since the design of both the LCL filter and the controller is done separately, considerable tuning efforts have to be exerted when compared to inverters using an L filter. Consequently, an integrated co-design of the filter and the controller for an LCL-type GCI is proposed in this paper. The control strategy includes only a PI current controller and a proportional grid voltage feed-forward controller. The capacitor is removed from the LCL filer and the design procedure starts from an L-type GCI with a PI current controller. After the PI controller has been settled, the capacitor is added back to the filter. Hence, it introduces a resonance frequency, which is identified based on the crossover frequencies to accommodate the preset PI controller. Using the proposed co-design method, harmonic standards are satisfied and other practical constraints are met. Furthermore, the grid voltage feed-forward control can bring an inherent damping characteristic. In such a way, the good control performance offered by the original L-type GCI and the sharp harmonic attenuation offered by the latter designed LCL filter can be well integrated. Moreover, only the grid current and grid voltage are sensed. Simulation and experimental results verify the feasibility of the proposed design methodology.

• Korean Journal of Materials Research
• /
• v.26 no.8
• /
• pp.412-416
• /
• 2016

The electrical properties of Au/n-type Ge Schottky contacts with different contact areas were investigated using current-voltage (I-V) measurements. Analyses of the reverse bias current characteristics showed that the Poole-Frenkel effect became strong with decreasing contact area. The contribution of the perimeter current density to the total current density was found to increase with increasing reverse bias voltage. Fitting of the forward bias I-V characteristics by considering various transport models revealed that the tunneling current is dominant in the low forward bias region. The contributions of both the thermionic emission (TE) and the generation-recombination (GR) currents to the total current were similar regardless of the contact area, indicating that these currents mainly flow through the bulk region. In contrast, the contribution of the tunneling current to the total current increased with decreasing contact area. The largest $E_{00}$ value (related to tunneling probability) for the smallest contact area was associated with higher tunneling effect.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.6
• /
• pp.2227-2236
• /
• 2017

In order to solve the neutral-point voltage fluctuation problem of three-phase three-level T-type inverters (TPTLTIs), the unbalance characteristics of capacitor voltages under different switching states and the mechanism of neutral-point voltage fluctuation are revealed. Based on the mathematical model of a TPTLTI, a feed-forward voltage balancing control strategy of DC-link capacitor voltages error is proposed. The strategy generates a DC bias voltage using a capacitor voltage loop with a proportional integral (PI) controller. The proposed strategy can suppress the neutral-point voltage fluctuation effectively and improve the quality of output currents. The correctness of the theoretical analysis is verified through simulations. An experimental prototype of a TPTLTI based on Digital Signal Processor (DSP) is built. The feasibility and effectiveness of the proposed strategy is verified through experiment. The results from simulations and experiment match very well.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1229-1234
• /
• 2010

High quality and high speed multimedia services will be required in the next generation mobile communications. To satisfy these services, powerful error correction techniques are used. ARQ(Auto Repeat Request) techniques, aspects of the throughput, and FEC(Forward Error Correct) techniques have disadvantages in terms of reliability. H-ARQ(Hybrid Auto Repeat Request) systems have been studied extensively as a solution of these disadvantages. In this paper introduce double layer coding and H-ARQ type, proposed H-ARQ system using double layer coding methods. Simulate BER performance and throughput. And we suggest that according to channel condition suitable H-ARQ type.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.3
• /
• pp.349-361
• /
• 2008

The purpose of this study was to develop bodice basic patterns fitted on different body types of adult women. To meet this purpose, first, human bodies were measured using tight fitting technique and classified based on the shapes of upper trunk. The subjects were 214 women $20{\sim}39$ years of age. For the measurement of female upper trunk, tight fitting technique was utilized. The development of figures of upper trunks were obtained from women. These development of figures were then digitized and analysed using the PAD system. A total of 155 measurements were taken from each of the development of figures. then, 32 measurements were selected for the further analysis. As complimentary data, 22 direct body measurements using an anthropometric method and 23 body measurements using a photographic method from the side view pictures of the participants were also obtained. The results and discussions of this study are as follows: Using the body measurements from the development of figures, a factor analysis and a cluster analysis were conducted. As a result, the body types were classified into 5 different types, which differ in terms of bust volumes, shoulder slopes, shoulder tilts, back silhouettes, body axises. The prominent characteristics of each type are as follows: The first type has a large bust volume. The second type has a right figure. The third type has a rounded back silhouette. The fourth type has a back silhouette of scapular coming backward. Finally the fifth type has a shoulder tilted forward.