• International Journal of CAD/CAM
• /
• 제7권1호
• /
• pp.21-30
• /
• 2007

The inverse offset method (IOM) is widely used for generating cutter paths from the point-based surface where the surface is characterised by a set of surface points rather than parametric polynomial surface equations. In the IOM, cutter path planning is carried out by specifying the grid sizes, called the step-forward and step-interval distances respectively in the forward and transverse cutting directions. The step-forward distance causes the chordal deviation and the step-forward distance produces the cusp. The chordal deviation and cusp are also functions of local surface slopes and curvatures. As the slopes and curvatures vary over the surface, different step-forward and step-interval distances are appropriate in different areas for obtaining the machined surface accurately and efficiently. In this paper, the chordal deviation and cusp height are calculated in consideration with the surface slopes and curvatures, and their combined effect is used to estimate the machined surface error. An adaptive grid generation algorithm is proposed, which enables the IOM to generate cutter paths adaptively using different step-forward and step-interval distances in different regions rather than constant step-forward and step-interval distances for entire surface.

• Journal of Power Electronics
• /
• 제18권2호
• /
• pp.356-363
• /
• 2018

The combination of a buck converter and a forward converter can be considered to accomplish a high step-down non-isolated converter. To decrease the insufficient step-down ratio of a regular buck converter and to distribute switch voltage stress, a forward-integrated buck (FIB) converter is proposed in this paper. The proposed interleaved DC-DC converter provides an additional step-down gain with the help of a forward converter. In addition to its simple structure, the transformer flux reset problem is solved and an additional magnetic core reset winding is not required. The operational principle and an analysis of the proposed FIB converter are presented and verified by experimental results obtained with a 240 W, 150 V/24 V prototype.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.312-317
• /
• 2001

Modifying effects of the rectangular forward step for suppressing the unsteady pressure fluctuation during interaction between the upstream vortical flow with the edge are studied numerically. The vortical flow is modeled by a point vortex, and the unsteady pressure coefficient is obtained from the velocity and the potential field. To investigate the effects of the edge shape the rectangular forward step is chamfered with various angles. Calculation show that the pressure peaks become decreased by increasing the vortex height as well as the chamfering angle. The pressure amplitudes are very sensitive to the change of the initial vortex height. From this study we can find out that the chamfered edge has two effects; the one is that it suppresses the pressure amplitude generated from the edge, and the other is that it decreases the time variation of unsteady pressure fluctuation. These modifying concepts can be applied to attenuate the self-sustained oscillation mechanism at the open cavity flow.

• 산업공학
• /
• 제10권3호
• /
• pp.125-132
• /
• 1997

We proposed a 2-step neural network approach for estimating machining parameters of electric discharge wire cut. The first step net, which is described as a backward neuro-estimation, is designed for estimating coarse cutting parameters while the second phase net, as a polishing forward neuro-estimation, is utilized for determining fine parameters. Sequential estimation procedure, based on backward and forward net, is performed using the net's approximation capability which is M to 1 and 1 to M mapping property. Experimental results an given to evaluate the accuracy of the proposed 2-step neuro-estimation.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.66-69
• /
• 2008

In this paper, The author present a load current feed-forward compensator by method that improve voltage controller of Step-down Chopper to get stable output voltage to sudden change of load current. To confirm the characteristicsof a presented load current feed -forward compensator compared each transfer function of whole system that load current feed-forward compensator is added with transfer function of whole system that existent voltage controller is included using Mason gains formula in Root locus and Bode diagram. As a result the pole of system is improved, extreme point of the wave and system improves, and size of peak value and phase margin of break frequency in resonance frequency confirmed that is good. Therefore, presented control technique could confirm that reduce influence by perturbation and improves stationary state and dynamic characteristics in output of Step-down Chopper.

• Structural Engineering and Mechanics
• /
• 제56권5호
• /
• pp.855-870
• /
• 2015

In this paper the effects of fling-step and forward-directivity on the seismic performance of steel eccentrically braced frames (EBFs) are addressed. Four EBFs with various numbers of stories (4-, 8-, 12- and 15-story) were designed for an area with high seismic hazard. Fourteen near-fault ground motions including seven with forward-directivity and seven with fling-step effects are selected to carry out nonlinear time history (NTH) analyses of the frames. Furthermore, seven more far-field records were selected for comparison. Findings from the study reveal that the median maximum links rotation of the frames subjected to three set of ground motions are in acceptable range and the links completely satisfy the requirement stated in FEMA 356 for LS performance level. The arrival of the velocity pulse in a near-fault record causes few significant plastic deformations, while many reversed inelastic cycles result in low-cycle fatigue damage in far-fault records. Near-fault records in some cases are more destructive and the results of these records are so dispersed, especially the records having fling-step effects.

• 한국소음진동공학회논문집
• /
• 제12권3호
• /
• pp.213-220
• /
• 2002

Modifying effects of the rectangular forward step for suppressing the unsteady pressure fluctuation during interaction between the upstream vortical flow and the edge are studied numerically. The vertical flow is modeled by a point vortex, and the unsteady pressure coefficient is obtained from the velocity and the potential fields. To investigate the effects of the edge shape the rectangular forward step is chamfered wish various angles. Calculation shows that the pressure peaks become decreased by increasing the vortex height as well as the chamfering angle. The pressure amplitudes are very sensitive to the change of the initial vertex height and its strength. From this study we can find out that the chamfered edge has two effects; the one is that it suppresses the pressure amplitude generated from the edge, and the other is that it decreases the time variation of unsteady pressure fluctuation. These modifying concepts can be applied to attenuate the self-sustained oscillation mechanism at the open cavity flow.

• 정보보호학회논문지
• /
• 제19권5호
• /
• pp.143-149
• /
• 2009

본 논문에서는 SHA-3의 1 라운드 후보로 제안된 알고리즘인 ARIRANG의 단계수가 축소된 버전들에 대한 역상 공격을 소개한다. 이 공격은 단계 1부터 단계 33까지의 ARIRANG-256 및 ARIRANG-512의 33단계 OFF(Original FeedForward1) 버전의 역상을 찾아내며, 단계 1부터 단계 34까지의 ARIRANG-256 및 ARIRANG-512의 31단계 MFF(Middle Feed-Forward1) 버전의 역상을 찾아낸다. 공격 복잡도는 ARIRANG-256에 대해서 약 $2^{241}$이고 ARIRANG-512에 대해서 약 $2^{481}$이다.

• 한국항공우주학회지
• /
• 제30권1호
• /
• pp.28-35
• /
• 2002

공동흐름에서 직각 계단은 커다란 소음의 원인이 되어 많은 사람들의 와류와 직각계단의 상호 작용 시에 발생되는 소음의 저감 방안을 연구하여 왔다. 본 연구에서는 2차원 저아음속 와류 흐름이 전향계단을 지날 때 발생되는 유동 소음을 전향계단의 형상 변화를 통한, 즉, 계단의 모따기 양과 각도를 바꾸어 가면서 수치적으로 계산하였다. 내부 유동장을 구하기 위해서 비압축성 비점성 이산와류 모델을 가정하였으며, 유동정보로부터 원거리로의 음향장 계산은 MAE 이론을 적용하여 구하였다. 음원에서의 음압과 음압강도를 모따기 높이 및 모따기 각도와 최기 와류의 높이를 변화시켜가면서 다양하게 수치적인 결과를 얻어내었다. 본 연구를 통해서 계단에 접근하는 와류에 의한 원거리 음압은 모따기 양이 계단 높이의 30%에서 모따기 각도가 $15^{\circ}C$에서 $30^{\circ}C$°사이일 때 가장 소음이 적게 발생되는 결과를 얻어내었다.

• 소성∙가공
• /
• 제8권2호
• /
• pp.178-187
• /
• 1999

The Cross rolling between flat jaws, as a kind of hot forging, is the forming method to make the axisymmetric multi-step shaft by its rotation and pressure between flat jaws which move in opposite direction. The purpose of this study is to propose the optimal geometric data for shape development of the forward forming region. All data described on this paper are quantified by experiment from initial shape design to final shape development. As the result, proper geometric data are proved that lenth of the first forming area in the forward forming region is 1.5 times larger than circumference of work-piece and the progress angle changes 3 times smoothly.