• Transactions of Materials Processing
• /
• v.23 no.4
• /
• pp.199-205
• /
• 2014

The current study examines the effect of the analytical parameter values on the theoretical forming limit diagram (FLD) based on the Marciniak-Kuczynski model (M-K model). Tensile tests were performed to obtain stress-strain curves and determine the anisotropic properties in the rolling, transverse and diagonal direction of SPCC sheet materials. The experimental forming limit curve for SPCC sheet material was obtained by limiting dome stretching tests. To predict the theoretical FLD based on the M-K model, the Hosford 79 yield function was employed. The effects of three analytical parameters - the exponent of the yield function, the initial imperfection parameter and the fracture criterion parameter - on the M-K model, were examined and the results of the theoretical FLD were compared to the experimentally measured FLD. It was found that the various analytical parameters should be carefully considered to reasonably predict the theoretical FLD. The comparison of the acceptable forming limit area between the theoretical and experimental FLD is used to compare the two diagrams.

• Journal of Industrial Technology
• /
• v.19
• /
• pp.67-74
• /
• 1999

The mechanical properties including forming limit and deep-drawability of commercially-used sheet metals were experimentally estimated in this study. Uniaxial tensile test to obtain basic mechanical properties was carried out, followed by limiting dome height (LDH) test and forming limit diagram (FLD) test to quantitatively evaluate the sheet-formability. Deep drawing and reverse drawing tests were also performed to find out the critical values of the blank holding force and the gap between the die and the blank holder which enabled the deep drawing and reverse drawing of a successful cop without any wrinkle or fracture. The thickness of the cup wall along the rolling-, transeverse- and $45^{\circ}$-directions was measured and compared with one another. And the punch force-stroke curve and the critical punch force expected from the theory coincided with the experimental result very well for mild steel while not for aluminium alloy.

• Transactions of Materials Processing
• /
• v.15 no.6 s.87
• /
• pp.467-472
• /
• 2006

The forming limit diagram of tube is required for the part design and the formability analysis of tube hydroforming. The finite element analyses of simple bulge test were done to obtain the various strain combinations on FLC. The finite element analysis results were shown that the bursting at various strain combinations could be induced by simple bulge test. The experiment oi tube bulge test was carried out according to the test condition that obtained from finite element analysis and the left hand side of forming limit diagram was built.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.240-243
• /
• 1995

This paper describes the process design and forming limit of the forged hinge produec with the axial protrusion on the sheet metal. Process design is consisted of preform and forging process. In this case, the forged hinge product can be formed in a single workpiece without assembling another axial part to it. Process design of the forged hinge product is analyzed by the commercial FEM program. It is known that process design with perform process, shown by the FEM simulaion, can bring the forming limit of the forged hinge product to a great expansion.

• Transactions of Materials Processing
• /
• v.6 no.4
• /
• pp.300-310
• /
• 1997

A finite element inverse method is introduced for direct prediction of blank shapes, strain distributions, and reliable intermediate shapes from desired final shapes in axisymmetric multi-step deep drawing processes. This mothod enables the determination of process disign. The approach deals with the Hencky's deformation theory. Hill's second order yield criterion, simplified boundary conditions, and minimization of plastic work with constraints. The algorithm developed is applied to motor case forming, and cylindrical cup drawing with the large limit drawing ratio so that it confirms its validity by demonstrating resonably accurate numerical results of each problem. Numerical examples reveal the reason of difficulties in motor case forming with corresponding limit diagrams.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1994.03a
• /
• pp.92-100
• /
• 1994

Forming limit diagrams for three different galvanized deep drawing quality steel sheets have been measured by hemispherical punch stretching. The experimental forming limit diagrams have been compared with results calculated using the shear instability criterion and the M-K model which takes into account a strain gradient effect resulting from bending (curvature) of a flat sheet by punch stretching. The measured data were in good agreement with the results calculated using exponent M value of 8 in Hosford's yield criterion for the M-K model and M= 6 for the shear instability model.

• Transactions of Materials Processing
• /
• v.7 no.4
• /
• pp.354-363
• /
• 1998

In order to analyze the stretch forming characteristics of tailored blanks, laser welded blanks of different thickness and strength combinations were prepared and stretching tests were done. The stretching formability of laser welded blanks was reduced as increasing the deformation restraining force ($strength{\times}thickness$) ratio between two welded sheets. Weld line movement was attributed to strain concentration at weaker sheets and resulted in fracture at weaker sid, so that fracture could be predicted by the forming limit of the weak sheet. In the case of a welded blank with the similar deformation restraining force rations between two welded sheets, crack occurred at weld and its forming limit was about 15% less than the base sheet. The effects of lubrication and weld line position on stretch-ing formability were also investigated by experiments. Lower friction did not always give better formability for tailored blanks. Stretching formability was observed to be improved as increasing the area of weak sheet.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10b
• /
• pp.22-25
• /
• 2003

The forming limits are studied for cold upsetting of high strength aluminium alloy in the present paper. Different geometry ratio and frictional conditions are investigated in the forgeability test to evaluate the forming limits and also to obtain the various strain paths. The critical fracture value can be obtained by integrating along the strain path till free surface crack initiation. To predict the damage evolution of cold upsetting, the computer-aided evaluation of forming limits is obtained by using the finite-element software DEFORM-3D and the modified Cockcroft-Latham criterion. The predicted theoretical limit strains agree quite well with the experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.546-551
• /
• 1997

In sheet metal forming, since the surface area of workpiece is apparently larger than the volume of it, the surface condition of the sheet metal is much varied. The formability of sheet metal is decided by the forming limit and the macroscopic suface defect as like fracture and wrinkle, and microscopic asponent, The factors affected in forming limit are stain herdening exponent, strain-rate scnsitivity exponent, anisotropic coefficient. The increasing of surface roughness is decresed the forming limit curve. It is known that the greater plastic deformation the more surface roughness by Kienzle, Osadaka. The purpose of this study is to investigate the influences of surface roughness in a uniaxial tension and the traperzoidal-shaped box drawing.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.10a
• /
• pp.162-169
• /
• 2004

In press forming of sheet metals, the material sheet is usually subjected to very large plastic strain under in-plane stressing. Moreover, the sheet also very often is subjected to out-of-plane compressive force between tools such as the upper and lower dies, the blank holder and the die, and so forth. In this paper, it is clearly demonstrated theoretically that out-of-plane stress may notably raise the forming limit strain and thus it can be effectively utilized to avoid earlier fracture of the sheet in press forming.