• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.293-296
• /
• 2002

In this paper, we proposed a beam tilting microstrip patch array antenna for the reception of satellite signals by using low cost copper etched polyester films and foams. The configuration and coupling mechanism of the proposed antenna are similar to the dipole Yagi-Uda antenna. It is composed of 3 layers of polyester films and three layers of foam. In order to prevent unwanted radiation and coupling loss by microstrip feeding networks and parasitic patches, a stacked layer with rectangular slots above the driver patch array is inserted. The 16${\times}$8 element microstrip Patch way antenna is Presented by experimental results. Its beam patterns are affected by many parameters such as sizes of the patches, gap between the patches. characteristics of the substrates, feeding method, etc. Owing to its complexities of various design parameters, both simulation and experiment were performed. The fabricated antenna received DBS signal from KOREASAT 3 by doing nothing but adjusting azimuth direction.

• Journal of computational fluids engineering
• /
• v.19 no.1
• /
• pp.15-20
• /
• 2014

Accurate simulation of free-surface wave flows around a ship is very important for better hull-form design. In this paper, a computational fluid dynamics (CFD) code, termed SNUFOAM, which is based on the open source libraries, OpenFOAM, was developed to predict the wave patterns around a ship. Additional anti-diffusion source term for minimizing a numerical diffusion, which was caused by convection differencing scheme, was considered in the volume-fraction transport equation. The influence of the anti-diffusion source term was tested by applying it to free-surface wave flow around the Wigley model ship. In results, the band width of the volume fraction contours between 0.1 to 0.9 at the hull surface was narrowed by considering the anti-diffusion term.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.2
• /
• pp.202-209
• /
• 2005

A new effective thick-layered RP process, Transfer-type Variable Lamination Manufacturing using expandable polystyrene foam (VLM-ST) has been developed with thick layers and sloped surfaces. VLM-ST has the innate advantages by virtue of its working principle: high building speed, low cost for introduction and maintenance of VLM-ST apparatus, little staircase surface irregularities of parts. Despite these advantages in VLM-ST, the surface roughness of VLM-ST parts is still inadequate to be used as RP master patterns for rapid tooling (RT). This paper describes the systematic and effective methodology to remove the laminated pattern and improve the surface roughness for VLM-ST parts. From the results of surface finishing of VLM-ST parts, it can be seen that the laminated pattern is completely removed and the surface characteristics such as surface roughness, surface hardness, and paintability are improved.

• Journal of Microbiology
• /
• v.37 no.2
• /
• pp.66-72
• /
• 1999

Mycolic acid-containing actinomycetes associated with extensive foaming in the aeration basin of the activated sludge process were isolated and analyzed by phenotypical, chemotaxonomical and phylogenetic methods. Whole cell sugar patterns of two isolates were pattern A. The nearly complete sequences of the 16S rRNA genes (rDNAs) of the isolates were determined and compared by using several tree-making algorithms. With polyphasic methods, strain SCNU1 was identified as Gordona sputi, and strain SCNU5 assigned to the genus Tsukamurella. The presence of opportunistic pathogens of chronic lung infections within foams can cause public health problems and render waste-treatment processes inefficient.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.11
• /
• pp.85-92
• /
• 2003

In this paper, a multiple U-shaped slot antenna on 5㎓ band is designed, fabricated, and measured. The prototype consists of a U-shaped slot and two Invert U-shaped slot. To obtain wide bandwidth, the foam layer is inserted between ground plane and substrate. After various parameters, length, width, position of U-shaped slot horizontal, interval length between two invert U-shaped slot, feeding position and airgap width, optimized, a multiple U-shaped slot antenna is fabricated and measured. The measured results of the antenna are compared with its simulated results. A 2:1 VSWR impedance bandwidth of 20.4% is achiedved by employing this technique. The gain is about 5.5㏈i. The experimental far-field patterns are stable across the pass band.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.3
• /
• pp.258-266
• /
• 2017

Numerical simulations of turbulent two phase flows around KCS have been performed to investigate effects of trim conditions on ship resistance of KCS in short waves by utilizing waves2foam. The wave lengths of LPP/2 and LPP/4 with 1m and 2m wave heights were imposed at inlet boundary. The resistance reduction at 2m trim by head and the increase of resistance at trims by stern were observed regardless of wave lengths and wave heights. The hull pressure on fore-and-aft rather than wave patterns around bulbous bows was mainly responsible for the total resistance coefficients of KCS in short waves. A phase diagram of contribution of hull pressure to the total resistance coefficients disclosed that the phase of representing the maximum resistance in time history played an important role in the effect of trim conditions on ship resistance of KCS in short waves.

• Journal of the Korean Home Economics Association
• /
• v.46 no.9
• /
• pp.137-146
• /
• 2008

This study was conducted in order to spread out lower body 3D scan data of men in their twenties. The aim was to achieve slacks pattern with ease allowance through comparison with existing flat patterns. For conversion of 3D scan data into 20 pattern, reference lines were established by using Rapid Foam in 3D shape analysis software. 2C-AN program and Yuka CAD were used to convert 20 pattern earned with straight posture of 3D scan data into slacks pattern by using Triangle Simplification & Runge-Kutta Method. In order to achieve this we needed to set a line 9cm below the hip line, to array vertex of each block to crease line while maintaining the horizontal line. And then we needed to set ease allowance in back crotch and to set waist circumference or hip circumference ease allowance in side seam of slacks. Results showed that long front crotch length can be achieved if 3D scan data is compared with 20 existing flat pattern. Slacks pattern that raise front crotch by about 1.5cm compared to back crotch and also possess ease allowance in back crotch area are great in appearance evaluation.

• Journal of Korea Foundry Society
• /
• v.17 no.1
• /
• pp.93-99
• /
• 1997

A possibility of production of aluminium matrix composites by using the lost foam process was investigated. Silicon carbide particles, graphite particles, and stainless steel wires were used as reinforcement materials. The reinforcement materials were introduced to the polystyrene to form patterns via injection molding process. The results obtained from this experiment can be summarized as follows. In Al/SiCp system, the particles with the radius of $100{\mu}m$ and over were entrapped in the matrix in the case of upward freezing of which solidification direction was opposite to floating direction of the particles. And few particles were entrapped in the matrix in downward freezing. In Al/graphite system, almost no particles were entrapped in the matrix except the area chill attatched. When the thickness of polystyrene slice was 4mm in Al/stainless steel wire system, the floating tendency of fibers was observed to increase as the distance from the ingate was increased.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.386-390
• /
• 2016

Water aeration is an effective water treatment process, which involves the injection of air or air-water mixture into water treatment reservoir commonly through pipes. The main purpose of water aeration is to maintain healthy levels of dissolved oxygen (DO), which is the most important water quality factor. The pipes' operating conditions are important for controlling the efficiency and effectiveness of aeration process. Many studies have been conducted on two-phase flows in pipes, however, there are a few studies to deal with small s ale in millimeter. The main objective of this study is to perform 2-dimensional two-phase simulations inside various straight pipes using the computational fluid dynamic (CFD) OpenFOAM (Open source Field Operation And Manipulation) tools to examine the influence of flow patterns on bubble size, which is closely related to DO concentration in a water body. The both flow regimes, laminar and turbulence, have been considered in this study. For turbulence, Reynolds-averaged Navier-Stokes (RANS) has been applied. The coalescence and breakage of bubbles caused by random collisions and turbulent eddies, respectively, are considered in this research. Sauter mean bubble diameter and water velocity are compared against experimental data. The simulation results are in good agreement with the experimental measurements.

• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.5
• /
• pp.278-286
• /
• 2020

Reynolds-averaged Navier-Stokes simulations have been performed to investigate an effect of numerical region with high resolution for Kelvin wave around KRISO container ship on its resistance. In the present study, 13 millions cells were used to describe wave profile along the ship hull and Kelvin wave patterns. In order to control a size of numerical region with high resolution for waves around the hull, we employed relaxation zones from a side boundary of numerical domain in which Kelvin wave was suppressed. When the far-field Kelvin wave was not precisely resolved due to the relaxation zone, the instantaneous history of ship resistance was affected although the time average of ship resistance showed -1.15~2.1 % errors. Especially, the damping characteristics of ship resistance in time history was significant when using a large relaxation zone in the side boundary.