• Journal of Magnetics
• /
• v.15 no.2
• /
• pp.91-98
• /
• 2010

The paper presents results of a study on the selective separation technology of ferrous and non-ferrous metals from broken light bulbs. The proposed method is to use magnetic fluids to obtain a magnetic fluid based- separation. [1] The study was conducted using three types of waste materials: regular light bulbs, auto light bulbs and neon tubes. In order to process the waste materials, a six stages technologic flow was developed: a) separation of light bulbs components; b) Physical and chemical analysis of raw materials; c) grain conditioning of the raw material; d) dry magnetic separation of ferrous components; e) magnetic fluid separation of non-magnetic material; f) recovery of the magnetic fluid adhered to the surface of the separated material grains. [2] This study shows that magnetic fluid separation is only profitable for regular and auto light bulbs and is not profitable in the case of neon tubes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.1
• /
• pp.108-116
• /
• 2001

The vortex tube is a simple device which separates fluid stream into a cold stream and a hot stream without any chemical reaction. The process of energy separation in the vortex tube has caused a great deal of interest. Although many studies on energy separation in the vortex tube using air as the working fluid have been made so far, few experimental studies treated energy separation for incompressible fluid. So, an experimental study for the energy separation in the vortex tube using the water which is essentially an incompressible fluid is presented. When working fluid is the water, the best geometric values of nozzle area ratio and number of nozzle holes are 0.155, 6 respectively. These geometric values are showed by the similar values which are presented by compressible fluid as working fluid. But hot side mass fraction of which maximum temperature drop is happened are different from compressible fluid.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.4
• /
• pp.118-127
• /
• 1996

Flow patterns of fluid flow in dividing trbe were visualized, and the energy losses due to dividing were measured in laminar dividing flow of the viscoelastic fluid and its solution in tube junctions with dividing angles of $90^{\circ}$, $60^{\circ}$, $65^{\circ}$ and $15^{\circ}$. Two separation zones were observed. swelling of the streamline to the main tube or to lateral tube was observed. The sizes of the separation zones depend on the Reynolds number, the dividing angle and the dividing flow rate. The energy loss coefficients decrease with increasing Reynolds number, but their decreasing rate decreases with increasing Reynolds number as the sizes of the separation zone increase. The effect of dividing angle on the energy loss coefficients and separation is greater for main tube than for the lateral tube.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.349-352
• /
• 2001

Shape separation method - a separation process which utilizes the fact that particles of different shape behave differently in force fields- is regarded as an useful measure for recycling, mineral processing, upgrading powdered material and so on. In this study, a trial was given to shape separation method using fluid field to recover pure diatom skeleton - which is thought to have many uses in itself and potential for various applications -from low grade diatomaceous earth of southeastern part of the Korean Peninsula. The striking difference of shape between diatom skeleton and other minerals like clay and quartz made it natural to choose shape separation method. Considering the size of particles to be separated, among many possible methods of shape separation, hydrodynamic field using hydrocyclone was adopted. And it resulted in recovery of pure diatom skeleton with high purity

• Applied Science and Convergence Technology
• /
• v.24 no.5
• /
• pp.196-202
• /
• 2015

Human blood consists of 55% of plasma and 45% of blood cells such as white blood cell (WBC) and red blood cell (RBC). In plasma, there are many kinds of promising biomarkers, which can be used for the diagnosis of various diseases and biological analysis. For diagnostic tools such as a lab-on-a-chip (LOC), blood plasma separation is a fundamental step for accomplishing a high performance in the detection of a disease. Highly efficient separators can increase the sensitivity and selectivity of biosensors and reduce diagnostic time. In order to achieve a higher yield in blood plasma separation, we propose a novel fluid wing structure that is optimized by COMSOL simulations by varying the fluidic channel width and the angle of the bifurcation. The fluid wing structure is inspired by the inertial particle separator system in helicopters where sand particles are prevented from following the air flow to an engine. The structure is ameliorated in order to satisfy biological and fluidic requirements at the micro scale to achieve high plasma yield and separation efficiency. In this study, we fabricated the fluid wing structure for the efficient microfluidic blood plasma separation. The high plasma yield of 67% is achieved with a channel width of $20{\mu}m$ in the fabricated fluidic chip and the result was not affected by the angle of the bifurcation.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.2
• /
• pp.10-14
• /
• 2019

In order to improve resource value, separation of nonferrous metals obtained from crushed materials of home appliances is required. In this study, we aimed to develop a continuous separation system by magneto-Archimedes method using magnetic fluid as a medium and the permanent magnet as a magnetic field source. Firstly, the separation conditions were examined in which only copper is settled and the difference in levitation positions between aluminum and other metals are over 1 cm. Based on the results, levitation experiment of each metal and separation experiment from the mixture of nonferrous metals were confirmed. The separation experiment showed that the continuous separation of copper and aluminum from a mixture of nonferrous metals is possible.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.3
• /
• pp.215-222
• /
• 2009

Jets issuing through small holes in a wall into a freestream has proven effective in the control of flow separation. This technique is known as the vortex generator jet (VGJs) method. If a precursor signal of separation is found, the separation control system using VGJs can be operated just before the onset of separation and the flow field with no separation is always attained. In this study, we measured the flow field and the wall static pressure in a two-dimensional diffuser to find a precursor signal of flow separation. The streamwise velocity measurements were carried out in the separated shear layer and spectral analysis was applied to the velocity fluctuations at some angles with respect to the diffuser. The pattern of peaks in the spectral analysis changes as the divergence angle increases over the angle of which the whole separation occurs. This change in the spectral pattern is related to the enhancement of the growth of shear layer vortices and appears just before the onset of separation. Therefore, the growth of shear layer vortices can be regarded as a precursor signal to flow separation.

• KSBB Journal
• /
• v.19 no.4
• /
• pp.263-268
• /
• 2004

The separation method using chiral stationary phase in preparation of chiral compound was wildly used, but in this work, supercritical fluid chromatography was suggested in the stability to resolve the chiral mixtures. To determine the optimum operating condition of the racemic ibuprofen, the retention factor and resolution with change in pressures, temperatures and the contents of IPA % (vol.) in CO$_2$ were investigated. The retention factor was decreased with increase in pressure and decrease in temperature. The factor was also influenced by the content of IPA in mobile phase, while the resolution was worse with a increase in IPA %. From the experimental results, the desirable separation condition was 130 bar, 311.15 K and 4% IPA in CO$_2$. Compared to the asymmetric peak shape by liquid chromatography, that of supercritical fluid chromatography was symmetric which was a favorable condition for preparative separation.

• Journal of Aerospace System Engineering
• /
• v.17 no.4
• /
• pp.28-33
• /
• 2023

In this study, computational fluid dynamics was used to analyze the flow bias generated as air supplied by a fan passes through ducts, piping, and a coal separation screen. The flow bias of the air flow is mostly caused by the spatial characteristics of the fan volute and duct, and the internal baffle and the coal separation screen at the outlet cause strong pressure losses that dampen the flow bias. ANSYS CFX was used for computational fluid dynamics, and since the baffle and the coal separation screen are shaped like perforated plates with many small holes uniformly distributed, actual modeling for analysis was not possible. Therefore, the Porous Loss Model was applied. The evaluation of the flow bias was analyzed based on the velocity distribution of the Porous Loss Model at the outlet surface of the coal separation screen obtained from the computational fluid dynamics results.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.2
• /
• pp.312-314
• /
• 2005