• 센서학회지
• /
• 제1권1호
• /
• pp.35-41
• /
• 1992

기체와 액체의 유숙을 측정하기 위한 반도체 기술을 이용한 소형의 정온도형 유속센서가 제작되었다. 유속센서는 유속에 영향을 받는 대류 열전달만을 검출하도록 설계되었고, 다른 종류의 열전달과 간섭효과는 기준센서의 사용으로 상쇄되도록 하였다. 원리는 유동에 의한 센서 양단전류의 변화로 유속을 측정하는 것이다. 이 유속센서의 실험은 수돗물로 가는 관(지름 8mm)을 사용하여 수행되었다. 그 결과 센서의 소비전력과 유속의 제곱근 사이의 관계는 유속이 0-200cm/sec 범위에서 거의 선형으로 나타났다.

• 한국가시화정보학회지
• /
• 제14권2호
• /
• pp.12-17
• /
• 2016

In this work, we investigate the flow velocity controllability of a diffuser-type multiple hydrofoil duct by experimental and numerical flow visualization approaches. The flow velocity controllability is analyzed by changing the angle of the hydrofoil near the outlet, which is the diffuser, while the incoming flow velocity is 0.6 m/s in the experiment. When the diffuser angle is changed from 0 to 7.5 degree, the maximum velocity inside the duct is varied from 1.35 m/s to 1.52 m/s. Also, it is shown from the numerical analysis that the maximum velocity is varied from 1.09 m/s to 1.17 m/s in the same condition. Thus, the aspect of the acceleration in the duct due to the increase of the diffuser angle is similar between the both approaches. Therefore, the multiple hydrofoil duct can be used to control the flow speed inside the duct for continuously extracting power close to a rated capacity.

• Coupled systems mechanics
• /
• 제13권3호
• /
• pp.247-275
• /
• 2024

The paper studies the influence of the fluid flow velocity and flow direction in the initial state on the dispersion of the axisymmetric waves propagating in the inhomogeneously pre-stressed hollow cylinder containing this fluid. The corresponding eigenvalue problem is formulated within the scope of the three-dimensional linearized theory of elastic waves in bodies with initial stresses, and with linearized Euler equations for the inviscid compressible fluid. The discrete-analytical solution method is employed, and analytical expressions of the sought values are derived from the solution to the corresponding field equations by employing the discrete-analytical method. The dispersion equation is obtained using these expressions and boundary and related compatibility conditions. Numerical results related to the action of the fluid flow velocity and flow direction on the influence of the inhomogeneous initial stresses on the dispersion curves in the zeroth and first modes are presented and discussed. As a result of the analyses of the numerical results, it is established how the fluid flow velocity and flow direction act on the magnitude of the influence of the initial inhomogeneous stresses on the wave propagation velocity in the cylinder containing the fluid.

• 한국해안·해양공학회논문집
• /
• 제31권1호
• /
• pp.9-16
• /
• 2019

유속의 크기와 블레이드의 기하학적 형상 변화에 따라 발생하는 조류발전용 쉬라우드 시스템 내 유속 변화를 분석하기 위하여 수리모형실험과 수치해석적 방법을 이용하였다. 모형실험을 통해 시스템의 유입부에서 유속 변화와 블레이드 형상변화에 따른 고유 회전수를 계측하였으며, 수치해석을 통해 쉬라우드내 유속 변화를 분석하였다. 실험 유속이 약 28% 증가하고, 익형의 형상을 적용하였을 때, 쉬라우드 유입부에서 계측된 유속은 최대 약 56% 증가하는 경향을 보였다. 한편, 익형 형상을 적용한 블레이드가 설치된 경우 유입부에서의 유속은 일반 블레이드에 비해 최대 14% 증가하는 경향을 보였으며, 회전수 역시 동일 조건에서 가장 높은 수치를 보였다. 수리실험과 수치해석 결과는 약 13%의 오차를 보였으며, 각각의 결과에서 보이는 유속 변화에 대한 경향은 유사하다. 쉬라우드 내 유속 변화를 수치해석으로 분석한 결과 유입부 대비 블레이드 앞부분에서 유속은 최대 1.7배 증가하는 경향을 보였다. 본 연구를 통해 얻은 시스템 내 유속 변화 분석 결과는 효율적인 조류발전용 쉬라우드 시스템 개발에 필요한 기초 자료를 제시할 수 있을 것으로 판단된다.

• 대한기계학회논문집B
• /
• 제28권2호
• /
• pp.181-188
• /
• 2004

The frequency characteristics in an axial flow fan operating at a design and three off-design operating conditions have been investigated by measuring the velocity fluctuation of a tip leakage vortex and a wake flow. Two hot-wire probe sensors rotating with the fan rotor. a fixed and a moving ones, were introduced to obtain a cross-correlation coefficient between two sensors as well as the fluctuating velocity. The results show that the spectral peaks due to the fluctuating velocity near the rotor tip are mainly observed in the reverse flow region of higher flow rates than those in the peak pressure operating condition. However, no peak frequency presents near the rotor tip for near stall condition. Detailed wake flow just downstream of the rotor blade was also measured by the rotating hot-wire sensor. The peak frequency of a high velocity fluctuation due to Karman vortex shedding in the wake region is mainly observed at the higher flow rate condition than that in the design point.

• 조명전기설비학회논문지
• /
• 제23권5호
• /
• pp.9-17
• /
• 2009

본 논문은 발전소 보일러 및 제철소 고로의 미분탄 연소방식에 적용이 가능한 유량계 개발에 관한 연구로서 분체의 밀도와 속도로 미분탄의 유량을 측정하는 시스템을 개발하였다. 관에 흐르는 미분탄의 밀도는 관의 표면에 전극을 설치하여 기준극과 측정극사이의 커패시터를 이용하여 측정한다. 속도는 일정 거리에 두 개의 전극을 설치하고 이 전극으로부터 두 개의 파형을 교차 상관관계 알고리즘을 이용하여 계산하였다. 분체의 유량을 측정된 밀도와 속도에 의하여 계산한다. 이 시스템에 설치된 로드셀에 의한 데이터와 개발한 유량 측정 시스템의 데이터를 비교하여 신뢰성을 확인하였다.

• 설비공학논문집
• /
• 제3권1호
• /
• pp.1-10
• /
• 1991

The purpose of this study is to lay groundwork for a complete analysis of two component flow by analyzing a single component flow made of continuous fluid without dispersed phase. In order to achieve uniform velocity distributions which are desirable in designing an optimum spray column direct contact heat exchanger, the influence of injection nozzle orientation has been investigated for axial and radial injections. The results that radial injection ensures more uniform velocity distributions compared to the axial case. The flow characteristics in a spray column have been investigated with various L/D values and inlet velocities, the most uniform internal velocity distributions have been obtained for the case of L/D=10 and 0.1m/sec. In the present investigation, it is shown that radial injection method for the continuous flow is advantageous in obtaining desirable uniform velocity distributions in a spray column. It is also found that as the value of L/D increases and the inlet velocity decreases, the flow improves to be better uniform velocity distributions.

• 대한기계학회논문집B
• /
• 제24권7호
• /
• pp.924-929
• /
• 2000

This paper addresses a new technique of measuring the mean flow velocity over the cross sectional area of the pipe using sound field reconstruction. When fluid flows in the pipe and two plane waves propagate oppositely through the medium, the flow velocity causes the change of wave number of the plane waves. The wave number of the positive going plane wave decreases and that of negative going one increases in comparison to static medium in the pipe. Theoretical backgrounds of this method are introduced in detail and the measurement of mean flow velocity using the sound field reconstruction is not affected by velocity profile upstream of microphones.

• 한국정밀공학회지
• /
• 제17권1호
• /
• pp.209-215
• /
• 2000

Precision forging technology that can control flow velocity of workpiece have been developed to minimize the amounts of machining. To get the uniform rib length, flow velocity distribution is needed to be estimated and controlled. Computer-aided design is known for very effective to estimate the deformation behavior and design the die for controlling the flow velocity. In this study, die design to control the deformation velocity are investigated using the DEFORM-2D about rib-web shape parts. Also we can get uniform rib length by enforcing the back pressure at end section of rib. The applied load of back pressure farming is lower than that of conventional forging. These results are analysed and confirmed by the experiment.

• Nuclear Engineering and Technology
• /
• 제55권3호
• /
• pp.1118-1124
• /
• 2023

Experimental study on the fluidelastic instability (FEI) of a curved tube bundle in single phase downward cross flow is investigated for the design qualification and analysis input preparation of helical coiled steam generator tubing. A 6×9 normal square curved tube array with equal and different vertical/horizontal pitch-to-diameter ratio was under-tested up to 6 m/s in term of gap flow velocity to measure the critical velocity for FEI. The critical velocity for FEI was measured at the turning point from the vibration amplitude plot along the gap flow velocity. Our test results were compared with straight tube results and published data in the design guideline. The applicability of the current design guidelines to a curved tube bundle is also assessed. We found that introducing frequency difference in a curved tube array increases the critical velocity for fluidelastic instability.