• Economic and Environmental Geology
• /
• v.44 no.1
• /
• pp.59-70
• /
• 2011

The surface sediment distribution in a tidal flat in 2001 was compared with that of 2008 using high spatial resolution remote sensing images and a GIS-based analysis. Maps of the surface sedimentary facies for each time frame were induced by an IKONOS data acquired in February, 2001 and a KOMPSAT-2 data acquired in April, 2008 using an object-based classification method. The area ratio of each surface sedimentary facies were estimated, and the results were compared each other for deducing the change in the sedimentary facies during the time interval. The result showed that the percentage of grains larger than very fine sand (0.0625 mm) has increased considerably since the early 2000s in the Hwangdo tidal flat. Mud flat facies has decreased 5.81 % in the late 2000s compared with the early 2000s. However, mixed flat and sand flat have increased 4.46% and 2.14%, respectively. A field campaign also supported the result. This study showed that the monitoring of changes in the surface sedimentary facies in the tidal flat is possible through a GIS-based analysis using high spatial resolution remote sensing images.

• Korean Journal of Mathematics
• /
• v.25 no.4
• /
• pp.537-554
• /
• 2017

In this paper, we study the surfaces foliated by ellipses in three dimensional Euclidean space ${\mathbf{E}}^3$. We prove the following results: (1) The surface foliated by an ellipse have constant Gaussian curvature K if and only if the surface is flat, i.e. K = 0. (2) The surface foliated by an ellipse is a flat if and only if it is a part of generalized cylinder or part of generalized cone.

• Journal of the Korean Society of Combustion
• /
• v.14 no.4
• /
• pp.7-16
• /
• 2009

Porous metal plates (Metal fiber, muti-hole metal plate) using mainly in surface burner are known to have a corrosion and durability problem under high temperature condition. In this study, premixed flat flame with perforated ceramic tile of more durable cordierite material was examined with respect to combustion stability and emission. The flat premixed ceramic burner consists of perforated ceramic tile and various type of baffle plates to form stable surface flame. The results show that most stable flat flame is generated using baffle plate with open ratio of 0.193. In downward flat flame mode which is widely used in condensing boiler, CO is measured below 50ppm from equivalence ratio 0.755 to 0.765 and $NO_X$ is measured below 12ppm from equivalence ratio 0.75 to 0.79. It is also found that the range of blue flame in flame stability curve becomes wider with increasing heat capacity.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.5
• /
• pp.130-136
• /
• 2001

The purpose of this study is an evaluation of flat end mills to develop appropriate tools for the high speed machining. First of all, several flat end mills which are produced by different makers are selected to analyze the performances of the tools. Experimental works are also executed to measure cutting farce, tool wear and surface roughness for different cutting conditions. And then the results are compared and analyzed for developing optimal cutting tool in the high speed condition.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.203-206
• /
• 2001

This paper presents a straightness measurement system for flat and long workpieces. The measurement system consists of a laser optical unit, a CCD camera and processing system, and a carrier system with a stylus. The carrier system accompanies the stylus, which displaces a retroreflector along the surface profile. The optical unit is used to optically amplify the displacement of retroreflector. The CCD camera and processing system finally identifies the vertical displacement of the stylus unit. The developed system is applied to two surfaces: ground surface and LM guide surface. The experimental results show that the developed system can measure the straightness of flat surfaces within sub-micron error.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.543-548
• /
• 2012

The use of glass applied to curved surface as a building material has increased in recent years. However, the curved glass is difficult to guarantee the quality in process of making it into double glazing, So it is vulnerable to thermal breakage. In this paper, when the glass broken during experiments, surface temperature difference on curved double glazing was compared to that of heat strengthened glass and flat glass. As a result, flat single glass was broken at temperature difference of 100~140 degrees but curved double glazing was broken at that of 40~60 degrees. Therefore, curved double glazing is more vulnerable than flat double glazing to thermal breakage, so it should be considered when applied to building facade.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.3
• /
• pp.107-113
• /
• 2002

This paper presents a straightness measurement system for flat and long workpieces. The measurement system consists of a laser, a CCD camera and processing system, a carrier system with a stylus, and some optical units. The carrier system accompanies the stylus, which displaces and retroreflector along the surface profile. The optical unit is used to optically amplify displacement of the stylus unit. The developed system is applied to a ground surface and a LM guide unit. The experimental results show that the developed system can measure the straightness of flat surface and moving systems.

• KIEAE Journal
• /
• v.12 no.3
• /
• pp.83-88
• /
• 2012

This study analyzed the measured value came out by the field test to verify the surface temperature reduction of the flat roof due to green roof, and confirmed the influence of the green roof based on it, and assessed the possibility of saving structures' energy and reducing $CO_2$ emission of structures. For the actual measurement, the differences of the average atmospheric temperature of the green roof and non-green roof flat roof were $8.67^{\circ}C$ and $0.787^{\circ}C$, and the average floor temperature gaps were $11^{\circ}C$ and $2.008^{\circ}C$ in October and November respectively. It was expected that if it's measured on around summer solstice that the temperature gets higher, the deviation of the surface temperature should be bigger, and it was confirmed that the green roof eventually raises insulating effect of structures and will influence on cooling and heating effects such as energy saving and insulating.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1145-1150
• /
• 2005

The aim of this paper is to investigate the effect of surface texturing on metal surface and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 is recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.872-879
• /
• 2010

High rock-fill embankment is relatively flexible, which makes crest of embankment subject to excessive amplification in displacement due to earthquake loading. To overcome problems related with site response in high embankment, it is essential to evaluate shear-wave velocity profile of the embankment with improved accuracy and reliability. In this aspect, an experimental research was performed to answer how to perform surface-wave tests and to analyze measurements at an embankment site with a sloping ground surface. Unlike flat ground surface, sloping ground may hamper and slow down propagation of surface waves due to multiple reflections and refractions in embankment. To figure out this reasoning for the effect of multiple reflections and refractions due to sloping surface, surface wave tests were performed at a reservoir embankment of Chung-Song in North KyeongSang Province. Parameters involved in surface wave tests at non-flat surface, including source directionality, geometry-related constraint and frequency components in source function, were investigated using field measurements.