• Water for future
• /
• v.14 no.4
• /
• pp.73-81
• /
• 1981

More than 650 numbers of water well ranging in depth from 100M to 200M were installed in South Korean Penninsula during the last decade for the purpose of industrial use and municipal water supply. Those data were compiled and synthesized by writer to determine their hydrogeologic occurences in accordance with their geologic and areal characteristics. Rocks yielding the deep seated ground water beared in the geologic primary and secondary porosities are classified into 6 groups according to their geologic, hydrogeologic, and topographic characteristics, that are: volcanic, sedimentary, meta-sediment and/or schist, andesitic, gneissic, and granitic rocks. The order of ground water productivity of the groups is as written above. Even granitic rocks including porphyries, granite, and intermediate and basic plutonic rocks is considered to be the most poorest ground water yielding group among 6, it's average yield form a single well with average drilling depth of 116M is about 225 cubic meters per day if it's drilling site is properly located. Generally speaking, seizable geologic structures such as fractured, sheared, and faulted zone at the flat surface and valley center yield almost 310% more of deep seated bet rock ground water in comparision with minor structures of joints, bedding planes, and so on that are occured at high land. 50 numbers of water well drilled at crystalline rocks were specially checked and measured it's ground water yie 1ds at each drilled depth to determine each interval's productivity while hammer drilling was going on. The results indicate that the specific capacity and yield of each water well at a depth below 70M to 80M was almost neglegible. It means that optimum well depth of crystalline rocks, except the area having seizable geologic structures, shall be not deeper than 80M.

• Membrane Journal
• /
• v.21 no.4
• /
• pp.377-388
• /
• 2011

Flat sheet microfiltration membranes were prepared with polysulfone (PSF), polyethersulfone (PES), and polyphenylsulfone (PPS) by an immersion precipitation phase inversion method. In this method, dimethyl formamide (DMF) and polyvinylpyrrolidone (PVP) were used as a solvent and a wetting polymer additive, respectively. 2-butoxyethanol (BE) was used as a nonsolvent additive catalyst to form pore. The morphology of membranes was investigated by scanning electron microscopy and micropermporometer. The permeability of the membranes was evaluated with the flux of pure water. When the BE was added, the pore size of membranes became larger than blank membranes. The changes in the morphology of membrane due to the BE addition depend on polymer structure. All membranes have similar mean pore size and porosity. The mean pore sizes of PSF, PES, and PPS membranes were 0.282, 0.330 $0.308{\mu}m$, respectively. The porosities of PSF, PES and PPS membranes were 68.5, 66.1, 66.4%, respectively. However, the PPS membrane showed higher pore density on surface and narrower pore size distribution than PSF or PES membrane does. As a result, the pure water flux of PPS membrane ($357L/m^2\;hr$) was higher than that of PSF ($196L/m^2\;hr$) or PES membrane ($214L/m^2\;hr$).

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.1026-1029
• /
• 2005

The feasibility of graphoepitaxial growth of compound semiconductors has been studied. Two kinds of substrates were prepared; one is smooth substrate, the other one is a periodic structured substrate. ZnO film was formed on both substrates by thermal evaporation of elemental Zn and natural oxidation of the deposited Zn. Thermal treatment was performed to improve the crystal quality and to investigate the effect of the periodic structure. Atomic force microscopy (AFM) and photoluminescence (PL) were used to characterize the samples. As a result, the improvement of crystallinity as annealing temperature increase, has been observed from both samples. The samples, annealed at 800 $^{\circ}$C, show the best crystal quality in terms of PL linewidth. Also the sample grown on grating structure shows better crystal quality than the sample grown on flat substrate. It implies that the periodic structure affects the crystallinity of the films, and the graphoepitaxy of compound semiconductors is possible by using appropriate surface structure.

• Applied Microscopy
• /
• v.30 no.1
• /
• pp.11-20
• /
• 2000

The morphological changes in normal and weathering hair shafts of the human scalp were investigated by using the transmission and scanning electron microscopes. The hair shaft composed of cuticular layer, cortex and medula. The surface of normal hairs are smooth and covered by imbricated cuticular scales. The cuticular layer consists of five to seven cuticle cells. These cells, which are flat and thin, measuring about $100{\mu}m$ long and $0.4{\mu}m$ thick, appears intercellular membrane complex in diameter 25 nm. The cortex composed of melanin granules and cornified cells, which multicomponent concentric microfibrils in diameter about 8 nm give rise to macrofibrils in diameter $0.5{\mu}m$ to $0.8{\mu}m$ encased in limiting membrane. The melanin granules are spherical shaped about $0.5{\mu}m$ in size and scattered between macrofibrils. The medulla in the normal hairs are $16{\mu}m$ in diameter centrally region of cortex. Normal hair shafts undergo progressive degenerative changes due to a variety of environmental insults. In the initial weathering process of hair, the cuticular scales became irregularly raised and broken, and then cuticle cells formed cytoplasmic vacuolation, following dissociated intercellular membrane complex, ultimately entirely lost and nuded cortex. Occasionally, transverse fissures were seen at hair shafts indicating that the hairs were deteriorated. Complete removal of the cuticular layer in the heavily damaged cortex portions appeared splitting of the cortical cell into its macrofibrils and scattering of melanin granules.

• Economic and Environmental Geology
• /
• v.24 no.3
• /
• pp.319-327
• /
• 1991

Cheju is the biggest island in Korean peninsula, consisted entirely of volcanic rocks and pyroclastic sediments. The topography is characterized by wide basalt plain in the low altitude but at the center of island, basalt volcano rises 1,950m above sea-level. Surface drainage is very poor, therefore water supply has been dependent on ground water and natural springs. There are about 1,650 production wells and most of them yield $1,000{\sim}2,000mm^3/day$. According to increase of ground water use, saline water is intruded in the low altitude of coastal area. Specially in the eastern coastal area, the topography is extensively flat and the level of ground water is very close to sea-level, at which overuse of ground water has brought saline intrusion up to maximum 6km far from the coast. Hydrochemical monitoring on this salt water intrusion is now undertaken on long term base.

• Restorative Dentistry and Endodontics
• /
• v.33 no.5
• /
• pp.428-434
• /
• 2008

The purpose of this study was to compare the microtensile bond strength in Class I cavities associated with different light curing modes of same light energy density. Occlusal enamel was removed to expose a flat dentin surface and twenty box-shaped Class I cavities were prepared in dentin. Single Bond (3M Dental product) was applied and Z 250 was inserted using bulk technique. The composite was light-cured using one of four techniques, pulse delay (PD group), soft-start (SS group), pulse cure (PC group) and standard continuous cure (CC group). The light-curing unit capable of adjusting time and intensity (VIP, Bisco Dental product) was selected and the light energy density for all curing modes was fixed at $16J/cm^2$. After storage for 24 hours, specimens were sectioned into beams with a rectangular cross-sectional area of approximately $1mm^2$ Microtensile bond strength $({\mu}TBS)$ test was per- formed using a univel·sal testing machine (EZ Test, Shimadzu Co.). The results were analyzed using oneway ANOVA and Tukey's test at significance level 0.05. The ${\mu}TBS$ of PD group and SS group was higher than that of PC group and CC group. Within the limitations of this in vitro study, modification of curing modes such as pulse delay and soft start polymerization can improve resin/dentin bond strength in Class I cavities by controlling polymerization velocity of composite resin.

• Archives of Plastic Surgery
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2007

Purpose: Human adipose tissue-derived stromal cells(hADSCs) can be expanded in vitro and induced to differentiate into multiple mesenchymal cell types. In this study we have examined various neuronal phenotypes and gene expression profiles of the hADSCs in the neuronal induction. Methods: The hADSCs were isolated from human adipose tissue and they were characterized by the flow cytometry analysis using CD13, CD29, CD34, CD45, CD49d, CD90, CD105 and HLA-DR cell surface markers. We differentiated the hADSCs into the neuronal lineage by using chemical induction medium and observed the cells with contrast microscopy. The immunocytochemistry and western blotting were performed using the NSE, NeuN, Trk-A, Vimentin, N-CAM, S-100 and ${\beta}$-Tubulin III antibodies. Results: The hADSCs were positive for CD13($90.3{\pm}4%$), CD29($98.9{\pm}0.7%$), CD49d($13.6{\pm}6%$), CD90 ($99.4{\pm}0.1%$), CD105($96%{\pm}2.8%$) but negative for CD34, CD45 and HLA-DR. The untreated cultures of hADSCs predominately consisted of spindle shaped cells and a few large, flat cells. Three hours after the addition of induction medium, the hADSCs had changed morphology and adopted neuronal-like phenotypes. The result of immunocytochemistry and western blotting showed that NSE, NeuN, Trk-A, Vimentin, N-CAM, S-100 and ${\beta}$-Tubulin III were expressed. However, NSE, NeuN, Vimentin were weakly expressed in the control. Conclusion: Theses results indicate that hADSCs have the capabillity of differentiating into neuronal lineage in a specialized culture medium. hADSCs may be useful in the treatment of a wide variety of neurological disorders.

• Membrane Journal
• /
• v.22 no.1
• /
• pp.23-34
• /
• 2012

In this study, we investigated the permeation property of single gases ($N_2$, $O_2$, $SF_6$, $CF_4$ through hollow fiber polymeric membrane (PSF, PC, PI) as a function of pressure and temperature to decide operating condition for $SF_6$ gas separation process. The results showed the gas permeation varied differentlydepending on the properties of gases and membrane. When permeance of each gases was represented as a function of temperature and pressure in 3 dimensional space, the surface of permeance was shown approximately flat. Thus, we established permeance models with forms of first-and second-order polynomial. These two models showed high goodness of fit. This indicates that the two polynomial models have enough applicability to predict the gas separation process.

• Korean Journal of Materials Research
• /
• v.21 no.11
• /
• pp.634-638
• /
• 2011

We report growth of epitaxial AlN thin films on c-plane sapphire substrates by plasma-assisted molecular beam epitaxy. To achieve two-dimensional growth the substrates were nitrided by nitrogen plasma prior to the AlN growth, which resulted in the formation of a two-dimensional single crystalline AlN layer. The formation of the two-dimensional AlN layer by the nitridation process was confirmed by the observation of streaky reflection high energy electron diffraction (RHEED) patterns. The growth of AlN thin films was performed on the nitrided AlN layer by changing the Al beam flux with the fixed nitrogen flux at 860$^{\circ}C$. The growth mode of AlN films was also affected by the beam flux. By increasing the Al beam flux, two-dimensional growth of AlN films was favored, and a very flat surface with a root mean square roughness of 0.196 nm (for the 2 ${\mu}m$ ${\times}$ 2 ${\mu}m$ area) was obtained. Interestingly, additional diffraction lines were observed for the two-dimensionally grown AlN films, which were probably caused by the Al adlayer, which was similar to a report of Ga adlayer in the two-dimensional growth of GaN. Al droplets were observed in the sample grown with a higher Al beam flux after cooling to room temperature, which resulted from the excessive Al flux.

• Applied Chemistry for Engineering
• /
• v.16 no.6
• /
• pp.822-826
• /
• 2005

Colloidal Silica (CS)/methyltrimethoxysilane (MTMS) and CS/MTMS/epoxysilane (ES) sol solutions were prepared using various synthesizing parameters such as reaction time and types of CS and silane. In order to understand their physical and chemical properties, sol-gel coating films on glass were fabricated. In the case of the CS/MTMS sol, the coating films had high contact angle and more enhanced flat surface than the CS/MTMS/ES sol. In the case of thermal stability, thermal degradation of the CS/MTMS and CS/MTMS/ES coating films did not occur up to $550^{\circ}C$ and $440^{\circ}C$, respectively. The coating films prepared from the CS/MTMS sol were thicker than those of the CS/MTMS/ES sol. In addition, the coating films prepared from single CS were thicker than those of mixed CS. Hardness of the coating films prepared from CS/MTMS increased by adding ES. In case of the mixed CS, the hardness decreased by adding ES.