• Journal of the Korean Geotechnical Society
• /
• v.33 no.10
• /
• pp.59-69
• /
• 2017

The tension load of the ground anchor inserted in the ground gradually changes over time. In this regard the change of the initial tension load is primarily decreased by the fixation condition of the fixing head and the mechanical characteristics of the tensile material. The subsequent additional tension load is a time-dependent loss mostly due to the fixing conditions of the bonded length and the surrounding ground properties of the field. In this paper, therefore, a measurement system using a relative displacement detector that can relatively easily measure the change of tension load is discussed. As a result of the review, it was confirmed that the results using the relative displacement detector are similar to those of the real scale model test, and it was also confirmed that similar results were obtained with the result of the pull-out test conducted on the ground anchors fixed to weathered rocks condition. In addition, a pull-out test was conducted on the test anchors whose initial tension load loss was relatively large and through this test pull-out behavior of the tension type ground anchors was verified.

• Journal of Welding and Joining
• /
• v.29 no.2
• /
• pp.72-79
• /
• 2011

The scope of this investigation is to evaluate the effect of joining parameters on the microstructural features and mechanical properties of dissimilar aluminum alloys, 1mm-thickness fixing AA6K31 at the top position and fixing AA5J32 at the bottom position. The friction stir lap welds were studied under various welding conditions, rotation speed of 1000, 1250, 1500rpm and welding speed of 100, 300, 500, 700mm/min, respectively. Mechanical test has been investigated in terms of tensile shear test and hardness test. The results showed that three type nugget shapes such as onion ring, zigzag type, hooking with the void, have been observed with revolutionary pitch. All welding conditions fractured at the HAZ of top plate, A6K31 and also the strength compare with base metal of lap joints were low efficiency, 52~63%. The thickness of fractured position was decreased with the lower heat input conditions. The relationships were excellent due to linear between the effective thickness of fractured position and peak load. The fractured position was the interface between joint area and not joint area. Also the strength efficiency compared with base metal was lower than decreasing rate of thickness because the hardness was decreased at fractured position due to softened material.

• Korean Journal of Human Ecology
• /
• v.15 no.5
• /
• pp.803-809
• /
• 2006

Korean traditional paper 'Hanji' made from the bark of the paper mulberry tree is a good handicraft material because of its high viscosity, durability, dyeability, toughness, flexibility, plasticity, and manipulability. Hanji has been used as a textile material such as cotton wool for protection and keeping us warm from cold weather. However, Hanji has many limitations, while other textile materials have many advantages of such as washability, being sunproof, and fast coloring. The purpose of this study is to review physical properties, formation ability, and dyeability of Hanji as a material of fashion accessary. The contents of this study are composed of 5 parts: 1. To introduce the necessities of this study, 2. To review a historical background of Hanji and to identify its physical characteristics as a fashion accessary material, 3. To review and to compare techniques such as bonding, quilting, knitting, creasing and holding, twisting, folding & braiding, paper pasting, coloring & cutting, and outwashing(?) in making Hanji fashion accessaries, 4. To review dyeing and finishing techniques to increase commercial value, 5. To identify the best fashion accessary materials made of Hanji. The most important characteristics of Hanji as a fashion accessary material are its toughness in a wet state, fast color fixing, and flexibility. Especially weaving and knitting are considered as the most desirable techniques to make fashion accessary products stronger and more practical.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.11 no.2
• /
• pp.169-181
• /
• 2009

The purpose of this study was to provide basic information for developing a smart taekwondo uniform with enhanced functionality for children by investigating the wearing condition and satisfaction of taekwondo uniform among taekwondo training children. The data were collected from 162 children living in Seoul and Daegu. For data analysis were performed descriptive statistics, ${\chi}2$ -test and t-test using SPSS Ver. 12. The results of the analysis are as follows. The results revealed that respondents wearing the general training uniform during their training period were the most. The dissatisfaction for the general training uniform was a high price, lack of symbolic, lack of functionality in textiles, lack of variety in design and unfittness of size in order. The developed uniform can adjust the length using a zipper type fastener, and can be used in all seasons as the lining is detachable. It also uses nano-silver material, and soil release finish. It enhances the functionality of movement by treating with raglan sleeve and sleeve hem velcro tape, and designs the upper garment in the draping. Safety is improved through attaching GPS, and elastic material is mixed in the neckline for putting on and off easily. Piece of cloth is added inside the closing of the upper garment. Rings are made for fixing the taekwondo uniform belt. Pocket is designed in the lower garment and colors are multiplied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.325-325
• /
• 2010

Piezoelectric linear motors have been widely studied for auto focusing devices of digital cameras and cellular phones due to their simple structure. In this paper, we confirmed that novel piezoelectric butterfly linear motor was fabricated and its dynamic properties were analyzed. The piezoelectric transducer (having size $9{\times}8{\times}1\;mm^3$) is composed of an elastic plate, which includes a tip for energy transfer and two fixing protrusions for fixture, and two piezoelectric ceramics. The butterfly linear motor has been designed and optimized using A TILA simulation program. The superposed motion is an elliptical vibration on the tip. The actual movement of the manufactured actuator was confirmed by a 3D laser dopier vibrometer and compared with the simulation results. The results of numerical study and experimental investigation will be used for the future optimization of the actuator and the realization of the advanced ultrasonic motor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.5
• /
• pp.408-412
• /
• 2010

The single-phase switched reluctance motor(SRM) generates the positive torque in the restricted section. So, it can not started by itself and the torque ripple is heavier than poly-phase. For self-starting and fixing rotating direction, the rotor should be placed at the rising inductance slope when stationary. The parking permanent magnet locates the rotor in the fixed position, which can be started by it-self. It is very simple and cost effective but has some drawbacks. It affects the rotor during the operation, so the characteristics of motor, such as a torque, speed, and ripple are changed to go bad. This paper presents the detent torque of parking magnet starting device through the finite element analysis and experiments. The finite element analysis is performed at incremental rotor positions over one detent torque cycle for any one pole. The prototype, fabricated in the previous research, is used for the experiments. The inductance, instant torque, and detent torque are calculated using the terminal voltage and phase current. Finally, the finite element analysis result and the experiment result are compared for analysis and validity.

• Fashion & Textile Research Journal
• /
• v.4 no.6
• /
• pp.517-523
• /
• 2002

This study examines whether there are differences in consumer's evaluation price zone on the clothing clue (the type of clothing, brand, time of fashion, place of origin, material. submaterial, place for sale) according to consumer purchasing behavior. Therefore the ultimate goal is to offer help in fixing price when establishing marketing of the clothing industry by grasping the actual price set by consumers under the IMP system. The female consumers of 20s and 30s were chosen as study subjects for their sensitivity to the purchase of clothing. The tests carried out in this research are: SPSSIPC+ is used for frequency Analysis. The Results of this study are showed as the following: It was analyzed that 4 types of consumer are the reasonable consumption oriented consumer, fashion oriented consumer, the no care of fashion consumer and high price oriented consumer Among the several kinds such as the type of clothing, brand, time of fashion, place of origin, material, submaterial, place for sale, only on the type of clothing, there are difference in the type of the consumers, on the time of buying clothes, in the behavior of buying clothes and also on the degree of fashion and the place of origin among such kinds.

• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.6
• /
• pp.277-283
• /
• 2020

Cu-Co-Si based alloy has a strengthening mechanism for Co₂Si intermetallic compounds deposited on the copper matrix after aging treatment and the solution treatment has a key influence on the strength and electrical conductivity of the final products. In this paper, the Cu-1.6%Co-0.38%Si alloy was fixed at the time and the solution treatment temperature was set at a temperature in the range of 800 to 950℃, and the change in mechanical properties was observed by fixing the temperature at 950℃ and changing the time. The microstructure was observed using an electron microscope and an optical microscope, and the changes in hardness, electrical conductivity, and bending workability after aging treatment were investigated. When the solution treatment time is less than 20 seconds, the solution treatment is not sufficient and the formation of precipitates contributing to the increase in hardness decreases and the hardness decreases after the aging treatment, and in more than 50 seconds, the hardness decreases due to the coarsening of the grains and the bending workability got worse.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.1
• /
• pp.47-52
• /
• 2019

Micro-LEDs show lower efficiencies compared to general LEDs having large areas. Simulations were carried out using ray-tracing software to investigate the change in light extraction efficiency and light distribution according to chip-size of blue flip-chip micro-LEDs (FC ${\mu}-LEDs$). After fixing the height of the square FC ${\mu}-LED$ chip at $158{\mu}m$, the length of one side was varied, with dimensions of 2, 5, 10, 30, 50, 100, 300, and $500{\mu}m$. The highest light-extraction efficiency was obtained at $10{\mu}m$, beyond which the efficiency decreased as the chip-size increased. The chip size-dependence of the FC ${\mu}-LEDs$ both without the patterned sapphire substrate, as well as vertical FC ${\mu}-LEDs$, were analyzed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.6
• /
• pp.594-597
• /
• 2023

We have proposed and demonstrated a fiber optic RH (relative humidity) sensor based on fiber Bragg grating covered with a polyimide film. As the polyimide film absolves the moisture in the air, its volume expands. As a result, the grating period of the FBG (fiber Bragg grating) covered with a polyimide film becomes wide and the Bragg wavelength is shifted. The sensor is implemented by fixing a 30 ㎛ thickness polyimide film on the surface of an optical fiber grating using an adhesive, and the characteristics of the device according to humidity are analyzed. The fabricated FBG RH sensor showed a high sensitivity of 0.0186 nm/RH% and a wide measurement range from 30% to 90%. The influence of environmental temperature on the characteristics of the RH sensor was also measured and analyzed. The feasibility of commercialization is presented.