• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.2
• /
• pp.218-225
• /
• 1999

This paper contains the computational simulation of a free rocket with a parachute and the development of a firing table for each range. To obtain the trajectory of the rocket, 6 DOF model of rocket with parachute was generated and the wind tunnel test was done for the input parameters. Good agreement was obtained between the analysis of trajectory and the flight test result. Also the trajectory error analysis was performed by the Monte Carlo simulation. As a result of simulation, the CEP(Circular Error Probability) of the firing table was calculated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.588-593
• /
• 2012

Nowadays, various forms of electro-optical rifle scope have been developed and used in order to enhance the accuracy of small arms. However, firing shock acceleration has characteristics of pyroshock having a big acceleration value with very short duration time, which the electro-optical scopes should be designed to sustain. In this paper, the firing shock acceleration, which is transmitted to the electro-optical scope, was measured and SRS (Shock Response Spectrum) analysis was performed by using the measured firing shock acceleration. Furthermore, a shock test condition using a drop-table shock tester, which can simulate the actual firing shock acceleration, was devised. The devised shock test condition will be utilized to test the electro-optical scope itself before attaching it to the small arms.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.2 s.25
• /
• pp.42-52
• /
• 2006

Tube erosion can be defined as a phenomenon for an increment of bore diameter, a declination of accuracy and utility of tube by firing. This study introduces the characteristics of tube life for the 155 mm K9 SHP Using a tube history book with bore measurement data and firing data of standard charge, this study analyzed the EFC vs Tube life and EFC with heat transfer effect formula as a consideration of continuous firing vs tube life. The results were compared with Firing Table(FT 155-K9-1) after the analysis. Also, this study suggests that CN98 tube can be rifled as 1000 EFC through the severe condition with continuous firing.

• Journal of Korean Institute of Industrial Engineers
• /
• v.42 no.3
• /
• pp.165-172
• /
• 2016

The purpose of this study is to investigate the ergonomic verification of suitability of the 4-wheeled hand cart to prevent musculoskeletal problems in the firing test range. Because of the increasing amount of firing test, the needs to develop a projectile transferring device such as 4-wheeled hand cart has been increased. For the 4-wheeled hand cart, the lifting and carrying activity in the manual handling method were transformed to pushing activity. The risk of low back pain for lifting and carrying the projectile by manual was estimated by NLE and 3D SSPP. On the other hand, the risk for pushing the 4-wheeled hand cart was estimated by psychophysical and biomechanical method such as Mital's equation, Snook's table and 3D SSPP. It was shown that the 4-wheeled hand cart reduced the risk of low back pain drastically with higher efficiency and design compatibility.

• The Journal of Korean Physical Therapy
• /
• v.32 no.5
• /
• pp.295-301
• /
• 2020

Purpose: The purpose of this study was to compare the electromyographic activity and onset time of the gluteus maximus (GM) and hamstring (HAM), lumbopelvic kinematics during three different prone table hip extension exercises in healthy individuals. Methods: Twenty subjects were participated. Electromyography device was used to measure the muscle activities and onset time of the GM and HAM muscles. An electromagnetic tracking motion device was used to measure lumbopelvic compensations. The subjects were asked to perform three different prone table hip extension [Prone table hip extension with the abdominal drawing-in maneuver on a chair (PTHEA), PTHEA with the ipsilateral knee flexion (PTHEAF), PTHEAF with hip 30 abduction (PTHEAFA)]. One-way repeated measures analysis of the variance and a Bonferroni post hoc test were used. Results: The electromyographic activity and onset time were significantly different among three conditions (PTHEA vs. PTHEAF vs. PTHEAFA)(p<0.01). The GM muscle activity and onset time were significantly greater and reduced during the PTHEAFA compared to PTHEA and PTHEAF (p<0.01). However, The HAM muscle activity and onset time were significantly smaller and delayed during the PTHEAFA compared to PTHEA and PTHEAF (p<0.01). Conclusions: PTHEAFA exercise can be recommended to facilitate the muscle activity and efficient muscle firing time of GM without HAM dominance.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.1
• /
• pp.95-104
• /
• 2016

To make a firing table of artillery with trajectory simulation, a precise trajectory model which corresponds with real firing test is required. Recent 4-DOF modified point mass trajectory model is considered accurate as a theoretical model, but fitting coefficients are used in calculation to match with real firing test results. In this paper, modified point mass trajectory model is presented and method of setting ballistic coefficient is introduced by applying optimization algorithms. After comparing two different algorithms, Particle Swarm Optimization and Covariance Matrix Adaptation - Evolutionary Strategy, we found that using CMA-ES algorithm gives fine optimization result. This fitting coefficient setting method can be used to make trajectory simulation which is required for development of new projectiles in the future.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.1
• /
• pp.31-38
• /
• 1991

A direct digital control technique of a current source using the phase-controlled rectifier is presented. A digital firing technique without sensing the line voltage is proposed. This scheme generates firing pulses directly from error signal between command and output voltage. Thus the phase detection transformers filters and zero-crossing detector are unnecessary. The synchronism is modeled and analized. Also a software synchronization algorithm is presented without a look up table and controls the system in real time with fast dynamic characteristics. Using the single-chip microprocessor 8097BH, the direct digital control is implemented with minimal hardware structure. Using the time-weighted performance index, the optimal discrete IPM control technique is also proposed to control the current of the PCR.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.2
• /
• pp.150-158
• /
• 1999

The process of designing protective circuits against damage by transient overvoltages requires much work and expensive equipment. However computer simulation using PSpice can overcome these problems. In this paper a gas tube and a ZnO varistor Pspice-model considering the steepness of the wave-front were presented. The effects of various waveforms on the transient behaviors and firing volt-ages of a gas tube were modeled by controlled voltage source E controlled current source G and TABLE function of PSpice. And the nonlinear characteristics of a ZnO varistor were modeled by controlled voltage source E and H. To estimate the characteristics of the models proposed various waveforms specified in IEC Std. 1000310-4-5 were used in the simulation and the actual tests. The simulation results were compared with test results and showed good agreement.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.389-392
• /
• 2008

The thrust axis alignment of the launch vehicle is very important because of the misalignment causes the unstable attitude control and results in mission failure. Generally, optical methods such as digital theodolite and laser tracker and mechanical method such as turn table method are used to thrust axis alignment. This article deals with the simple method of thrust axis alignment of Kick Motor.

• Journal of Korean Society for Quality Management
• /
• v.46 no.3
• /
• pp.739-752
• /
• 2018

Purpose: The purpose of this study was to investigate the relationship between kiln processing parameters and NOx emissions that occur in the sintering and calcination steps of the cement manufacturing process and to derive the main factors responsible for producing emissions outside emission limit criteria, as determined by category models and classification rules, using data mining techniques. The results from this study are expected to be useful as guidelines for NOx emission control standards. Methods: Data were collected from Precalciner Kiln No.3 used in one of the domestic cement plants in Korea. Thirty-four independent variables affecting NOx generation and dependent variables that exceeded or were below the NOx emiision limit (>1 and <0, respectively) were examined during kiln processing. These data were used to construct a detection model of NOx emission, in which emissions exceeded or were below the set limits. The model was validated using SPSS MODELER 18.0, artificial neural network, decision treee (C5.0), and logistic regression analysis data mining techniques. Results: The decision tree (C5.0) algorithm best represented NOx emission behavior and was used to identify 10 processing variables that resulted in NOx emissions outside limit criteria. Conclusion: The results of this study indicate that the decision tree (C5.0) can be applied for real-time monitoring and management of NOx emissions during the cement firing process to satisfy NOx emission control standards and to provide for a more eco-friendly cement product.