• 한국재료학회지
• /
• 제3권2호
• /
• pp.185-192
• /
• 1993

본 연구에서는 분극성을 갖는 미세분말/유전유체 분산계내의 전기유변효과를 mechanism을 중심으로 고찰하였다. 전기유변효과를 일으키는 mechanism을 (1)입자표면전도(surface conductance) (2)입자내부전도(bulk conductance(3) 유도분극(induced polarization)으로 구분하여 설명하였다. 소수성(anhydrous-base)전기유변유체 내의 미세분말 입자간 상호인력을 예측할 수 있도록 유도분극 mechanism을 적용하여 수학적으로 모델화 함으로써 전기유변효과를 향상 시키기 위한 재료선정의 기초로 하였다. 전기유변유체의 미세입자로 이용될 수 있다고 여겨지는 ceramic, ferrite 및 polymer등 7가지 재료를 선정하여 계산한 결과 ceramic및 ferrite입자가 입자간 상호인력이 큰것으로 나타났다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.402-405
• /
• 2001

The BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics were prepared by conventional mixed oxide method. The structural and dielectric properties of the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics with the sintering temperature were investigated. Increasing the sintering temperature, the 2$\theta$ value of BaTiO$_3$peaks were shifted to the higher degree and intensity of the BaTiO$_3$and BaNbO$_3$peaks were increased. In the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics sintered at 135$0^{\circ}C$ and 1375$^{\circ}C$, the grain was fine and uniform. Increasing the sintering temperature, the pore was decreased and the dielectric constant was increased. In the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics sintered at 1375$^{\circ}C$, the dielectric constant and dielectric loss were 5424, 0.02 respectively.ctively.

• 한국세라믹학회지
• /
• 제42권8호
• /
• pp.537-541
• /
• 2005

Silicon nitride is one of the most successful engineering ceramics, owing to a favorable combination of properties, including high strength, high hardness, low thermal expansion coefficient, and high fracture toughness. However, the impact damage behavior of $Si_3N_4$ ceramics has not been widely characterized. In this study, sphere and explosive indentations were used to characterize the static and dynamic damage behavior of $Si_3N_4$ ceramics with different microstructures. Three grades of $Si_3N_4$ with different grain size and shape, fine-equiaxed, medium, and coarse-elongated, were prepared. In order to observe the subsurface damaged zone, a bonded-interface technique was adopted. Subsurface damage evolution of the specimens was then characterized extensively using optical and electron microscopy. It was found that the damage response depends strongly on the microstructure of the ceramics, particularly on the glassy grain boundary phase. In the case of static indentation, examination of subsurface damage revealed competition between brittle and ductile damage modes. In contrast to static indentation results, dynamic indentation induces a massive subsurface yield zone that contains severe micro-failures. In this study, it is suggested that the weak glassy grain boundary phase plays an important role in the resistance to dynamic fracture.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 춘계학술대회 논문집
• /
• pp.17-21
• /
• 1995

Tw types of Pb(Mn$\sub$1/3/Nb$\sub$2/3/)O$_3$+PZT Ceramics had been fabricated by hot-pressing method. One had cause grain and the other had fine grain doe to Cr$_2$O$_3$ addition. These specimen were poled by applying the DC electric field in various steps. The effects of thermal aging on their piezoelectric characteristics and temperature stability of the frequency were investigated.

• 한국세라믹학회지
• /
• 제27권1호
• /
• pp.62-66
• /
• 1990

La-modified PbTiO3 Powders and ceramics were prepared by coprecipitation and salt decomposition method. In this process, fine and homogeneous single phase of La-modified PbTiO3 was synthesized at lower temperature than oxide mixing method. And these powders contributed to lowering calcination temperature and rising sintering properties. The properties of these powders and the change of properties with themperature and the effect of powder properties on sintering were investigated.

• 한국세라믹학회지
• /
• 제25권1호
• /
• pp.54-58
• /
• 1988

In order to depress PbO vaporization during calcination and improve sinterability in low temperature, a method for preparing homogeous Lead-Zirconate-Titanate (PZT) powder from aqueous salt solution by precipitation is described. In this method, single phae PZT fine powders are formed at above 500$^{\circ}C$. PZT-ceramics using these powders have high sinterability, and good sintering characteristics relatively low temp. (-high apparent density, low porosity, low water adsorption etc.)

• 한국분말재료학회지
• /
• 제10권1호
• /
• pp.57-62
• /
• 2003

The effect of bedding on the microstructure of $Si_3N_4$ added with ultra-fine SiC was investigated. The bedding and the addition of ultra-fine SiC effectively inhibited grain growth of $Si_3N_4$ matrix grain. The microstructures of the specimens sintered with bedding powder consisted of fine-grains as compared with the specimens sintered without bedding powder. In addition, the grain size and the difference of grain size between the specimens sintered with bedding and without bedding was reduced with increasing SiC content. Some ultra-fine SiC particles were trapped in the $Si_3N_4$ grains growed. The number of SiC particles trapped in the $Si_3N_4$ grains increased with increasing the grain growth. When ultra-fine SiC particles were added in the $Si_3N_4$ ceramics, the strength was improved but the toughness was decreased, which was considered to be resulted from the decrease of the grain size.

• Advances in materials Research
• /
• 제3권2호
• /
• pp.105-116
• /
• 2014

The microwave dielectric properties of $CeO_2$ nanoparticles (0.5, 1.0 & 1.5wt%) doped $Mg_2TiO_4$ (MTO) ceramics have been investigated at cryogenic temperatures. The XRD patterns of the samples were refined using the full proof program reveal the inverse spinel structure without any secondary phases. The addition of $CeO_2$ nanoparticles lowered the sintering temperature with enhancement in density and grain size as compared to pure MTO ceramics. This is attributed to the higher sintering velocity of the fine particles. Further, the microwave dielectric properties of the MTO ceramics were measured at cryogenic temperatures in the temperature range of 6.5-295 K. It is observed that the loss tangent ($tan{\delta}$) of all the samples increased with temperature. However, the $CeO_2$ nanoparticles doped MTO ceramics manifested lower loss tangents as compared to the pure MTO ceramics. The loss tangents of the pure and MTO ceramics doped with 1.5 wt% of $CeO_2$ nanoparticles measured at 6.5K are found to be $6.6{\times}10^{-5}$ and $5.4{\times}10^{-5}$, respectively. The addition of $CeO_2$ nanoparticles did not cause any changes on the temperature stability of the MTO ceramics at cryogenic temperatures. On the other hand, the temperature coefficient of the permittivity increased with rise in temperature and with the wt% of $CeO_2$ nanoparticles. The obtained lower loss tangent values at cryogenic temperatures can be attributed to the decrease in both intrinsic and extrinsic losses in the MTO ceramics.

• 한국분말재료학회지
• /
• 제17권5호
• /
• pp.399-403
• /
• 2010

The effects of $MnO_2$ doping on the crystal structure, ferroelectric, and piezoelectric properties of (K,Na)$NbO_3$ (KNN) ceramics have been investigated. $MnO_2$ was found to be effective in enhancing the densification and grain growth during sintering. X-ray diffraction analysis indicated that Mn ions substituted B-site Nb ions up to 2 mol%, however, further doping induced unwanted secondary phases. In comparison with undoped KNN ceramics, the well developed microstructure and the substitution to B-sites in 2 mol% Mn-doped KNN ceramics resulted in significant improvements in both piezoelectric coupling coefficient and electromechanical quality factor.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.38-49
• /
• 1994

In this study, grindability of some representative engineering ceramics are experimentally investigated using resin bond diamond wheel with conventional surface grinding machine, and proper grinding conditions which can be obtained from various experimental results are established also for mechanical components which are proper to domestic circumstances with high reliability. And through the results of experiment, it is confirmed that grinding energies of the ceramics, especially in the case of $Al_2O_3$, are lower than steel with same machining condition in the conventional grinding because of their fine-brittle fracture mode type removal process, though the ceramics are well-known to unmachinable materials. And moreover, the total pass numbers needed for spark-out process to be completed are depend on their mechanical properties because that grinding stiffness is different from each other. The grinding force, ginding power and ground surface roughness are also measured and compared. Furthermore, the experiments carried out in this study, some useful results are obtained with can guide to grind engineering ceramics with conventional surface grinding machine.