• 한국전기전자재료학회논문지
• /
• 제20권9호
• /
• pp.793-797
• /
• 2007

In this paper, the long time breakdown characteristic of the epoxy composite, which is widely used in the insulation system for high voltage application, was estimated with Weibull distribution. In the procedure of the estimation, the short time breakdown characteristics for the epoxy composite specimens, which were made with the variation of hardener and/or filler, were tested firstly. Then the long time voltage-to-time test was implemented. Finally, the long time breakdown voltage of each specimen was estimated with the parameters obtained from the statistical treatment with Weibull distribution. Base on the results, it has been found that the optimal weight ratio of epoxy resin/hardener/filler that has the excellent long time breakdown characteristic was 100/100/65. It was due to the silane treatment which relieves the electric field at the interface between filler and epoxy.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.107-110
• /
• 2005

This paper describes the design and fabrication of synchronous clock recovery module for S-DMB Gap Filler. Using the 2.304MHz TTL signal from gap filler tuner, clock recovery module with 10MHz output frequency including holdover function is designed. The measured performance of the clock recovery module shows a stability of less than 0.01ppm, 29 sec stability time, 10 sec holdover time, and maximum -113dBc/Hz@100Hz phase noise.

• 한국군사과학기술학회지
• /
• 제4권1호
• /
• pp.207-215
• /
• 2001

Plastic bonded explosive(PBX) is mainly composed of the nitramine-ploymer compositions. PBX is characterized by high velocity and pressure of detonation, low vulnerability and good thermal stability. Many important applications of PBX require the good adhesion between nitramine crystals and the binder. For PBXs as well as propellants, where good mechanical properties are of great importance, dewetting therefore must be prevented by strong adhesion between filler-binder. Adhesion depends on surface characteristics of filler and binder. In order to design for better adhesion, an understanding of the surface properties of explosive and binder is required. The surface free energies are calculated from contact angle values by the method of Kaelble. Critical surface tension of solids are calculated by Zisman plot. Critical surface tension is a useful parameter for characterizing the wettability of solid surface. In this study, HMX and 3 kinds of copolymers are selected, since they are widely used in many plastic bonded explosives. The technical objective of this investigation is to predict the interaction between filler and binder from their surface free energies.

• 한국세라믹학회지
• /
• 제31권9호
• /
• pp.957-968
• /
• 1994

Manufacturing process of porous glass by the filler method was studied. Commercial soda-lime-silicate glass powder was mixed with inorganic salt as the filler such as KCl, K2SO4, Na2SO4. Sintering shrinkages of mixed powders with the variation of sintering temperature were compared, and the effects of the fillers to shrinkages of mixed powder were increased in the order of Na2SO4${\mu}{\textrm}{m}$ of pore diameter were manufactured when the filler sizes 100~200 ${\mu}{\textrm}{m}$. The open pore volume of porous glass is determined by the quantity of filler and porous glasses having open pore volume between 30 and 70 vol% are available. Available sintering temperature range for preparation of porous glass is from the softening temperature of the glass powder to eutectic melting temperature of DTA curve of mixed powder.

• 한국분말재료학회지
• /
• 제11권4호
• /
• pp.288-293
• /
• 2004

The application concept of using a fail safety filter on the filtering system is to prevent the particle leakage when the main filter element is broken at high temperature. In this study, the metal filters were fabricated by pressureless sintering method. The mixture of stainless steel powders and filler metal binder solved in the water solutions of 5% PVA was compacted to form the cylindrical filter without pressure. The compacted filter were sintered in the vacuum sintering furnace at 120$0^{\circ}C$ for 1 hour. The metal filter(produced with powder of 640-840 ${\mu}m$ size) having more than above 50% porosity, 500${\mu}m$ pore size, and permeability of 7.3${\times}$10$^{-11}$m$^{2}$ plugged within 2.5 minute to prevent the leakage of maximum slip particle size of less than 3${\mu}m$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 추계학술대회 논문집
• /
• pp.171-174
• /
• 1995

Space charge formation in epoxy loaded with silica and calcium carbonate has been studied. The epoxy itself showed almost no charge at up to 40 kV/mm. The addition of fillers such as SiO$_2$and CaCO$_3$resulted in homocharge formation, which was attributed to the interfacial trapping of injected charge at epoxy/filler interfaces. The amount of charge showed a maximum at 20-40 parts per hundred resin above which the charge decreased gradually. This was tentatively attributed to the enhanced interconection of charge transport path by an increased filler content

• KIEAE Journal
• /
• 제7권4호
• /
• pp.119-126
• /
• 2007

In this study, we processed two procedures of application test of filler for fire-resistance utility that are new application methods of aerated concrete and properties test of aerated concrete according to mixing ratio because we investigated the better use of aerated concrete as filler for fireproof safety and we proposed basic data about standardization of mixing of aerated concrete. We measured flow and volume change of aerated concrete. And if its volume doesn't change, we added measuring unit weight and compressive strength. To test application of aerated concrete as filler for fireproof safety, we filled up aerated concrete to fireproof safety according to suitable mixing ratio. Then we measured maximum temperature of inner part of fireproof safety in accordance with the standard test of fireproof. According to the results, aerated concrete as filler for fireproof safety could be possibly used. So when we make aerated concrete, we should consider using an adding agent as well as a foaming agent.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2004년도 하계학술대회
• /
• pp.19-22
• /
• 2004

위성 DMB(Digital Multimedia Broadcasting)는 위성을 통하여 이동 흑은 고정 무선 가입자 수신기에게 비디오 방송 및 정지화상 CD 음질의 오디오 방송과 각종 데이터 서비스와 같은 Multimedia 서비스를 제공하는 서비스이다. 향후 새로운 사업으로 다양한 부가가치를 이끌어 낼 것으로 기대를 받고 있다. 우리나라의 경우 위성 DMB기술기준으로 System E방식이 선정되었다. 본 논문에서는 위성DMB 서비스 의 음영지역을 해소하기 위해 사용되는 재생중계방식의 중계기인 Gap Filler 개발에 대해 기술한다. System E용 Cap Filler용 보조 방송의 전송 방식 선정과 보조방송에서 주 방송으로의 변환 기법, Gap Filler 망설계시에 고려해야 할 사항 등에 대해 기술한다.

• 한국전기전자재료학회논문지
• /
• 제30권10호
• /
• pp.641-645
• /
• 2017

In this study, an epoxy insulation barrier for high voltage GIS was developed using epoxy and a filler with a Young's modulus of 11 GPa. The material was investigated using a simulation of the principal stress, displacement, and safety factors while optimizing the profile shape. The simulation showed that thelarger Young's modulus of the $Al_2O_3$ filler compared to the $SiO_2$ in the epoxy insulation can contribute to an increase in resistance to mechanical fracturing for theoptimized profile barrier in high voltage GIS. In addition, the safety factor was improved by 10%. It can be concluded that the mechanical fracturing properties of the insulation barrier can be enhanced by increasing the content of the elastic filler, $Al_2O_3$, for high voltage GIS applications.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.233-236
• /
• 2006

A dilatometer was used to investigate the effect of cure conditions and the presence of filler in an epoxy system. These studies showed shrinkage in the cured epoxy when heating it through the glass transition temperature region. The magnitude of the shrinkage, related to stress build up in the epoxy during curing, was influenced by the processing conditions, filler presence and the nature of the mold used to contain the resin. Cure and cyclic cure at a lower temperature, prior to a post cure, decreased the magnitude of observed shrinkage. Cure shrinkage decreased with number of cyclic cure. Post cured samples outside the mold led to less shrinkage compared with sample in the mold. And sample containing kaolin filler showed less shrinkage than unfilled sample.