• Journal of Powder Materials
• /
• v.18 no.6
• /
• pp.526-531
• /
• 2011

Fecralloy is the promising materials for high temperature exhaust filtering system due to the excellent its oxidation resistance property. In this research, Fecralloy nanoparticles coated Fecralloy thin foil was prepared by a single nozzle electrospray system in order to increase surface area of Fecralloy foil. Fecralloy nanoparticles were fabricated by electrical wire explosion method in ethanol using Fecralloy wires as a source material. Electrospray modes with applied D.C voltages to Fecralloy colloidal solution were investigated to make a stable cone-jet mode. Coated layers with and without additional heat treatment were observed by FE-SEM (field emission-scanning electron microscope) and tape test for evaluating their adhesion to substrate were performed as well.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.303-306
• /
• 1998

Electroluminescence is occurred when phosphor is located in electric field. Object of this research show powder electroluminescent device (PELD) for high brightness compared with conventional PELD. Single layer of PELD structured as follow (ITO/phosphor + dielectric/silver paste). To investigate optical properties of PELDS, EL spectrum, CIE coordinate system, Brightness of PELDs was measured. The suitable ratio between phosphor and dielectric in single layer of PELD was 7:3(phosphor: dielectric). At 200 V4OO Hz, high performance of PELD which had ratio of 7:3

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.66-66
• /
• 2010

잉크젯용 저온 Cu ink의 소성 특성을 향상 시키기 위해 소성 분위기롤 조절 하였다. 일반적으로 Cu는 산화가 잘되는 물질로 환원 분위기에서 소성이 이루어져야만 하기 때문에 acid, alcohol, aldehyde, ether와 같은 환원제를 소성시 사용하였다. 또한 1종의 환원제가 아닌 2종의 환원제롤 일정 비율로 섞음으로써 환원력를 조절하여 소성 품질을 향상 시킬 수 있었으며, 이러한 환원 분위기 조절을 통하여 300도 이하 저온에서 소성이 가능하였다. 또한 optical microscopy와 field emission scanning electron microscopy를 통해 막 품질과 미세조직의 치밀도를 확인하였고 배선 재료로써의 적용을 위해 resistance를 측정 비교하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.575-575
• /
• 2012

Synthesis of novel two dimensional materials has gained tremendous attention recently as they are considered as alternative materials for replacing graphene that suffers from a lack of bandgap, a property that is essential for many applications. Single layer molybdenum disulfide ($MoS_2$) has a direct bandgap (1.8eV) that is promising for use in next-generation optoelectronics and energy harvesting devices. We have successfully grown high quality single layer $MoS_2$ by a facile vapor-solid transport route. As-grown single layer $MoS_2$ was carefully characterized by using X-ray diffraction, Raman spectroscopy, field emission scanning electron microscopy and electrical transport measurement. The results indicate that a high quality single layer $MoS_2$ can be successfully grown on silicon substrate. This may open up great opportunities for the exploration of novel nanoelectronic devices.

• Textile Coloration and Finishing
• /
• v.23 no.2
• /
• pp.83-89
• /
• 2011

Poly(vinyl alcohol) (PVA), PVA/Montmorillonite (MMT), PVA/Silver (Ag), and PVA/MMT/Ag nanocomposite nanowebs were prepared by electrospinning technique in aqueous solution. In order to investigate the effect of inorganic materials on the morphology and thermal properties of PVA based nanocomposite nanowebs, experiments were performed with 5 wt.% of MMT and Ag. Field emission type scanning electron microscopy, transmission electron microscopy (TEM), reflection type X-ray diffraction (XRD), and thermal gravimetric analyzer were utilized to characterize nanocomposite nanowebs. TEM and XRD results show MMT and Ag were well dispersed in PVA nanowebs. Those inorganic nanoparticles enhanced thermal property of the nanocomposite nanowebs.

• Journal of Surface Science and Engineering
• /
• v.36 no.5
• /
• pp.398-405
• /
• 2003

The stainless steel wire requires good corrosion resistance and mechanical properties, such as drawing ability, combined with a high resistance to corrosion. For increasing drawing ability of stainless steel, Ni coating methods have been used in this study. However, there is no information on the electrochemical corrosion behavior of drawed wires after Ni coating. To investigate corrosion resistance and mechanical property of drawed wire, the characteristics of Ni coated wires have been determined by tensile strength tester, hardness tester, field emission scanning microscope, energy dispersive x-ray analysis and potentiodynamic method in 0.1 M HCl. The drawed stainless steel wires showed the strain-induced martensitic structure, whereas non-drawed stainless steel wire showed annealing twin in the matrix of austenitic structure. The hardness and tensile strength of drawed stainless steel wire were higer than that of non-drawed stainless steel wire. Electrochemical measurements showed that, in the case of drawed stainless steel o ire after Ni coating, the corrosion resistance and pitting potential increased compared with non-coated and drawed stainless steel wire due to decrease in the surface roughness.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.4
• /
• pp.436-440
• /
• 1999

The highly resolved absorption spectra of mer-[Cr(dpt)(Gly-Gly)]ClO4·H2O [dpt = di(3-aminopropyl)amine, H2Gly-Gly = glycylglycine] have been measured between 13000 cm-1 and 50000 cm-1 temperatures down to 2 K. The vibrational intervals were extracted by recording emission and far-infrared spectra. The characteristic infrared bands in meridional isomer were discussed. The four-teen electronic origins due to spin-allowed and spin-forbidden transitions were assigned. With the use of this electronic transitions, a ligand field optimization based on the exact known ligand geometry have been performed to determine more detailed bonding properties of Gly-Gly and dpt ligands. It is confirmed that the peptide nitrogen of the Gly-Gly has a weak π-donor property toward chrornium(Ⅲ) ion.

• Korean Journal of Materials Research
• /
• v.17 no.2
• /
• pp.73-80
• /
• 2007

For the sub-65 nm CMOS process, it is necessary to develop a new silicide material and an accompanying process that allows the silicide to maintain a low sheet resistance and to have an enhanced thermal stability, thus providing for a wider process window. In this study, we have evaluated the property and unit process compatibility of newly proposed composite silicides. We fabricated composite silicide layers on single crystal silicon from $10nm-Ni_{1-x}Co_x/single-crystalline-Si(100),\;10nm-Ni_{1-x}Co_x/poly-crystalline-\;Si(100)$ wafers (x=0.2, 0.5, and 0.8) with the purpose of mimicking the silicides on source and drain actives and gates. Both the film structures were prepared by thermal evaporation and silicidized by rapid thermal annealing (RTA) from $700^{\circ}C\;to\;1100^{\circ}C$ for 40 seconds. The sheet resistance, cross-sectional microstructure, surface composition, were investigated using a four-point probe, a field emission scanning probe microscope, a field ion beam, an X-ray diffractometer, and an Auger electron depth profi1ing spectroscopy, respectively. Finally, our newly proposed composite silicides had a stable resistance up to $1100^{\circ}C$ and maintained it below $20{\Omega}/Sg$., while the conventional NiSi was limited to $700^{\circ}C$. All our results imply that the composite silicide made from NiCo alloy films may be a possible candidate for 65 nm-CMOS devices.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.447-453
• /
• 2011

The monodisperse spherical $SiO_2$ particles were overcoated with $Y_2O_3:Eu^{3+}$ phosphor layers via a Pechini sol-gel process and the resulting $SiO_2@Y_2O_3:Eu^{3+}$ core-shell phosphors were subsequently annealed at $800^{\circ}C$ at an ambient atmosphere. The crystallographic structure, morphology, and luminescent property of core-shell structured $SiO_2@Y_2O_3:Eu^{3+}$ phosphors were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and photoluminescence (PL). The spherical, nonagglomerated $SiO_2$ particles prepared by a Stober method exhibited a relatively narrow size distribution in the range of 260-300 nm. The thickness of phosphor shell layer in the core-shell particles can be facilely controlled by varying the coating number of $Y_2O_3:Eu^{3+}$ phosphors. The core-shell structured $SiO_2@Y_2O_3:Eu^{3+}$ phosphors showed a strong red emission, which was dominated by the $^5D_0-^7F_2$ transition (610 nm) of $Eu^{3+}$ ion under the ultraviolet excitation (263 nm). The PL emission properties of $SiO_2@Y_2O_3:Eu^{3+}$ phosphors were also compared with pure $Y_2O_3:Eu^{3+}$ nanophosphors.

• Journal of Powder Materials
• /
• v.24 no.6
• /
• pp.457-463
• /
• 2017

Nanosized $Gd_2O_3:Eu^{3+}$ red phosphor is prepared using a template method from metal salt impregnated into a crystalline cellulose and is dispersed using a bead mill wet process. The driving force of the surface coating between $Gd_2O_3:Eu^{3+}$ and mica is induced by the Coulomb force. The red phosphor nanosol is effectively coated on mica flakes by the electrostatic interaction between positively charged $Gd_2O_3:Eu^{3+}$ and negatively charged mica above pH 6. To prepare $Gd_2O_3:Eu^{3+}$-coated mica ($Gd_2O_3:Eu/mica$), the coating conditions are optimized, including the stirring temperature, pH, calcination temperature, and coating amount (wt%) of $Gd_2O_3:Eu^{3+}$. In spite of the low luminescence of the $Gd_2O_3:Eu/mica$, the luminescent property is recovered after calcination above $600^{\circ}C$ and is enhanced by increasing the $Gd_2O_3:Eu^{3+}$ coating amount. The $Gd_2O_3:Eu/mica$ is characterized using X-ray diffraction, field emission scanning electron microscopy, zeta potential measurements, and fluorescence spectrometer analysis.