• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.7
• /
• pp.1541-1548
• /
• 2012

This paper proposes a new multipath-based routing protocol on MANETs with Fast-Recovery of failures. The proposed protocol establishes the primary and secondary paths between a source and a destination considering the end-to-end packet reception reliability of routes. The primary path is used to transmit messages, and the secondary path is used to recover the path when detecting failures on the primary path. If a node detects a link failure during message transmission, it can recover the path locally by switching from the primary to the secondary path. By allowing the intermediate nodes to recover locally the route failure, the proposed protocol can reduce the number of packet loss and the amount of control packets for setting up new paths. The simulation result using QualNet simulator shows that the proposed protocol was about 10-20% higher than other protocols in terms of end-to-end message delivery ratio and the fault recovery time in case of link fault was about 3 times faster than the other protocols.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.4
• /
• pp.29-36
• /
• 2009

The fuzzy controller of the FFH(Fuel Fired Heater) used for vehicle is designed in this study. Two of the most important things of the pre-heater are how fast it can be at the set temperature and how to reduce the temperature deviation in the space to a minimum. The temperature deviation of the existed FFH with PI controller for temperature controller was reduced. Also, the fuzzy controller improved the response characteristics, and then the performance was inspected. When setting the temperature in this designed fuzzy controller, it took 12 minutes in the existed PI control method to reach $25^{\circ}C$. However, it took 9 minutes and 20 seconds in the fuzzy control method. Therefore, it is proved that the fuzzy controller is better than the existed one with fast response performance as 2 minutes 40 seconds. The temperature deviation was $2.4^{\circ}C$ in the existed control method but $1.6^{\circ}C$ in the designed fuzzy controller. Accordingly, the temperature deviation was improved too.

• Journal of KIISE:Information Networking
• /
• v.30 no.5
• /
• pp.621-630
• /
• 2003

In this paper, we implemented SIP protocol that supports IPv6 and differentiated call processing scheme for NGN(Next Regeneration Network). In NGN, SIP processes call signaling among various application services. A softswitch and SIP server must give priority to sensitive services such as Fax, network management and home networking that require a fast call setup time. Also, the support of IPv6 is needed under consideration of All-IP. We proposed differentiated call processing scheme. The differentiated call processing scheme supports differentiated call processing as priority of service class on call processing in SW server We defined three service classes and use the Flow Label field of the IPv6 header for setting service class. Through the performance analysis, we proved that it improves throughput for call message with the high priority. The result of performance analysis demonstrates that differentiated call processing scheme gives better performance for the service requiring a fast session establishment in NGN.

• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1297-1303
• /
• 2021

Most thickness measurement techniques using X-ray radiation are unsuitable in field processes involving fast-moving organic films. Herein, we propose a Compton scattering X-ray radiation method, which probes the light elements in organic materials, and a new simple, non-destructive, and non-contact calibration-free real-time film thickness measurement technique by setting up a bench-top X-ray thickness measurement system simulating a field process dealing with thin flexible organic films. The use of X-ray fluorescence and Compton scattering X-ray radiation reflectance signals from films in close contact with a roller produced accurate thickness measurements. In a high-thickness range, the contribution of X-ray fluorescence is negligible, whereas that of Compton scattering is negligible in a low-thickness range. X-ray fluorescence and Compton scattering show good correlations with the organic film thickness (R² = 0.997 and 0.999 for X-ray fluorescence and Compton scattering, respectively, in the thickness range 0-0.5 mm). Although the sensitivity of X-ray fluorescence is approximately 4.6 times higher than that of Compton scattering, Compton scattering signals are useful for thick films (e.g., thicker than ca. 1-5 mm under our present experiment conditions). Thus, successful calibration-free thickness monitoring is possible for fast-moving films, as demonstrated in our experiments.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.39-49
• /
• 2011

Recently PBD method, one of acceleration of consolidation methods is used in the soft ground to shorten consolidation time for fast settlement during construction. It is economical and easy to work. Discharge capacity of PBD is sensitive in proportion to thickness of soft ground layer, and drainage of PBD declines due to disturbance effect in surrounding ground by mandrel used for vertical drainage setting and setting machines and type. Also, deviation of discharge capacity is large according to ground condition, construction condition and soil properties. In addition, when embankment loading is not conducted instantly after PBD setting due to rain or lack of embankment material supply, it causes leaving period problems. But cause and analysis of those problems for discharge capacity is lack. So, in this test, ground improvement and discharge capacity is investigated by implementing composite discharge capacity test for analysis of an effect factor of PBD discharge capacity with leaving period. After fixing the vertical drain on a cylindrical cylinder, put churned sample into the cylinder. Then leave 0day, 30day, 60day and 90day. And then, load following the loading step of 30, 70 and 120kPa using a pressure device. As a result, the longer leaving period, discharge capacity is reduced. It is caused by a decrease of discharge area caused by creep transformation moisture absorption of PBD filter after long leaving period.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.12
• /
• pp.1202-1209
• /
• 2004

This paper presents a design methodology of a Digital Servo Signal Processor for high speed CD-RW drive systems. The proposed Digital Servo Signal Processor enables us to develop CD-related systems for the very high speed applications and is one of the key components of the CD-RW systems. The proposed center compensation servo control is newly built for an actuator shaking due to the fast response of a step motor when it jumps to a long distance. A control method compensating for eccentricity of a disc is implemented for operating robustly at a higher rotational speed. This servo mechanism is more size efficient and less power consumed because it is implemented using a ARM7 embedded processor and hardware digital filters. Furthermore, it is convenient to upgrade firmware for the future required functions. From experimental results, we can see that the performance of the control system is improved greatly. The proposed servo algorithm shows a shorter setting time including a pull-in time and a faster access time. It can be applied easily to the DVD-ROM and the DVD-RAM which have the same optical structure.

• Management & Information Systems Review
• /
• v.2
• /
• pp.209-235
• /
• 1998

Traditional cost system is distorted due to the using unit-based measure. It is being criticized that it do a poor job of attributing the expenses of support resources to the production and sales of individual product. Activity Based Cost System expend the range of second-stage cost assignment drivers beyond the traditional measures of labor and machine times, units produced, and material quantities to allow for drivers that measure the amount of batch-level, product-sustaining, and facility-sustaining activities performed. It is a resources consumption model of organization, not just a more complex cost accounting of cost allocation system. This paper proposes a enterprise resource planning by activity based management. To effective performance system for company that want to be setting competitive levels, the information systems must support a fast moving, rapidly changing. Activity based management is a process of accumulating and tracing cost and performance da to a firm's activities and providing feedback of actual results against the planned cost to initiate corrective action where required. Therefore this system provides a highly powerful decision-making tool. To construct this system, we need Enterprise Resource Planning System. Since ERP is designed around the idea that rapid change and a degree of unhandled change is normal, it allows driving the customer's rapidly needs much deeper through the business cycle.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.23 no.1
• /
• pp.79-84
• /
• 2007

Mineral Trioxide Aggregate(MTA) has been used in Endodontic treatment successfully for more than 10 years. But the high cost of MTA limits its use in endodontics in Korea. Recently many studies have been done to compare MTA and Portland cements. To investigate the chemical constitutions of MTA (Proroot MTA, Tulsa Dental), Gray Portland cement (Lafarge Halla cement), White Portland cement(Union corp), and fast setting cement (SSangyong cement), we performed SEM(scanning electron microscope)(S4700, Hitachi) examination and EDS(Energy dispersive spectrometry)(emax, Horiba) analysis. SEM examination and EDS analysis were committed to and performed in SNU DRI (Seoul National University Dental Research Institute). We found that particles of MTA were relatively round, uniform in size, and compactly packed compared to Portland cements. Chemical constitutions of MTA, GPC, WPC and FSC were similar. It was shown that MTA contains much BiO2 . MTA and WPC showed less heavy metals such as Fe and Mg compared to GPC and FSC. FSC showed remarkably high aluminum content.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.301-304
• /
• 2003

Recently, the development of internet remote control system has been studied lively along with fast growth of internet. In this paper, we proposed the internet-based remote control and monitoring system using java platform. The apache web server that is now used worldwide was constructed for monitoring and controlling of an machine in administrator's web browser. We solved the limitation on security which is the biggest problem of internet control system due to strong security setting in web server. As a result of experiment which is used in the proposed remote internet control system, several time-delay occurred in internet. However, correct control result could be achieved without an error. And this system monitored informations of a RPM, temperature and the other condition in almost real time.

• Journal of the Korean Society of Safety
• /
• v.29 no.5
• /
• pp.1-6
• /
• 2014

When the fluid energy convert into kinetic energy due to water hammer, the propagation velocity of pressure wave appear. The propagation velocity of pressure wave(1050 m/s) of very fast could be damage to the pipeline system. If the occurrence of water hammer is due to down-pressure, the faster the air exhaust or supply device is needed. it is high Speed Air Valve. In this paper, Each 3.12, 3.13, 3.72, $3.74kg/cm^2$ pipeline pressure were setting, and then executed pressure rapid drop for obtaining a high Speed Air Valve Operating time and pressure change data. the result was that pipe line pressure stabilization time were each 0.98, 1, 1.22, 1.25 sec. In other words, that pressure drop experimental results pipe line pressure was equal to atmospheric pressure without negative pressure After about one second. The study result would be useful to pipe line system stability design because this data could be foresee pressure stabilization time.