• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2503-2508
• /
• 2005

In this paper, we propose a new discrete-time predictive current controller for a PMSM(Permanent Magnet Synchronous Motor). The main objectives of the current controllers are to ensure that the measured stator currents tract the command values accurately and to shorten the transient interval as much as possible, in order to obtain high-performance of ac drive system. The conventional predictive current controller is hard to implement in full digital current controller since a finite calculation time causes a delay between the current sensing time and the time that it takes to apply the voltage to motor. A new control strategy in this paper is seen the scheme that gets the fast adaptation of transient current change, the fast transient response tracking. Moreover, the validity of the proposed method is demonstrated by numerical simulations and the simulation results will present the improvements of predictive controller and accuracy of the current controller.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.2
• /
• pp.53.3-54
• /
• 2018

On June 16 AT2018cow (ATLAS 18qqn) was discovered as a bright and fast-evolving transient in nearby universe z ~ 0.01. It brightened by more than 4 mag within a day, and its light curve was decayed rapidly and has a high luminous peak which is more luminous than most of core-collapse supernova. It also overall showed a blue color in an unprecedented case of transients. There have been attempts to explain this behavior with existing models, but most of them have been insufficient except for one - tidal disruption by intermediate-mass black hole. We began to monitor this transient from about 4 days after the discovery until August 21 in the optical bands with 1m-class telescopes over the world. Here, we present a light curve of AT2018cow in the B, V, R and I bands, and analyze its photometric properties and compare to other transients and models.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1727_1728
• /
• 2009

Nowadays DC-DC converter has been used widely in electronic production. It has a high requirement in wide input voltage, load variations, stability, providing a fast transient response and lower overshoot. However, it is not easy to be controlled because of its nonlinearity. In this paper, the nonlinear model of DC-DC converter is approximatedby four linear models and sub-controllers are designed by using the LMI guaranteeing the stability of the sub-systems at the same time. For the robust of the control system, an integral sliding mode control (ISMC) is applied together with LMI fuzzy controller. The proposed controller supports a fast and almost no overshooting transient response for the DC-DC converter control.

• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1263-1271
• /
• 2014

A novel hysteresis PWM control strategy for synchronous buck converter is proposed. The proposed control strategy is based on ampere-second balance of the modulate capacitor, which not only offers faster transient response to meet the challenges of the power supply requirements of fast dynamic load changes, but also provides better stability and solves the compensation problem of error amplifier in the conversional voltage PWM control. Finally, the steady-state and dynamic operation of the control method is analyzed and verified by simulation and experimental results.

• The Journal of the Acoustical Society of Korea
• /
• v.7 no.2
• /
• pp.51-64
• /
• 1988

The frequency synthesizer thar has very short transient time is the key to construct the Fast Frequency Hopping(FFH) system. A Direct Digital Frequency Synthesizer(DDFS) whose transient time is in the nS range has been implemented and the performance of which has been examined through this paper. And by considering the hopping characteristic it is confirmed that the DDFS is suitable for the FFH system. Finally an improvement method which can greatly enhances the SNR with the state-of-the-art techniques and simplifies the system design is presented.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1523-1525
• /
• 1994

This paper describes a proposed very fast transient overvoltages(VFTO) measurement system suited for established gas insulated switchgear(GIS). The detecting system consists of a shield electrode connected to a buffer amplifier, and the transmission of the detected signal to an oscilloscope is made through an optical fiber. The bandwidth of the measurement system is 5 Hz to 30MHz. When determining the voltage dividing ratio by use of the commercial frequency voltage, the error is less than 0.5 %. Also, the data were obtained by the electric field probe and the high voltage probe, and their deviation for voltage dividing ratio were less than 1 %.

• Advances in aircraft and spacecraft science
• /
• v.5 no.2
• /
• pp.177-186
• /
• 2018

This paper deals with the idea to replace the usual high-level sine sweep test on shaker at system level, very severe, by a low level one completed by a transient test in the same configuration, in order to be more representative of the real environment, thus limiting over testing and improving the payload comfort. The problem of the transient test specification is first discussed. The proposed solution is to derive from LV/SC coupled analyses a shock response spectrum corresponding to two damping ratios. Then, the question of adequate shock synthesis is tackled. A new method with a given spectrum is considered for better potential and accuracy than the usual wavelets. A campaign on the Intespace bi-shaker devoted to system level showed its capability to perform the resulting test with one spectrum. First investigations to extend this approach to two spectra are in progress.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.686-690
• /
• 2004

This paper describes the performance improvement of transient response and the modeling of small aircraft onboard generator. As the characteristics of the stator coil which are a major parameters of transient response were improved, the characteristics of transient response could be increased, therefore, the improved generator can be satisfied with large and fast load changes. Established the control model of the generator, it could be possible to do the analysis of generator performance, and improve the operational stability of the generator system using the control model.

• Journal of KSNVE
• /
• v.6 no.4
• /
• pp.447-456
• /
• 1996

Dynamic characteristics of the bell-type structure including acoustic effects and transient dynamic problems were analyzed numerically. Natural frequencies, mode shapes and transient dynamic analysis used the finite element method with 3-D general shell element. Mode shapes and stress distributions of transient dynamic analysis were expressed by computer graphics. The method using this study was evaluated by comparision of theoretical results at reference papers(14), (15) and the experimental test using Fast Fourier Transform analyzer. Vibrational modes governing acoustic characteristics of the typical bell-type structure depended on the first flexural mode(4-0 mode) and the second flexural mode(6-0 mode). Asymmetric effects by Dangiwas, acoustic holes gave rise to beat frequencies, and the Dangjwa was found to be most effective. When impact load acted on the bell, stress concentration occured at the rim part of bell. It was found that the bell type structure should be designed thickly at the rim part in order to prevent impact load from stress concentration.

• ETRI Journal
• /
• v.42 no.5
• /
• pp.790-798
• /
• 2020

Herein, a low-ripple coarse-fine digital low-dropout regulator (D-LDO) without ringing in the transient state is proposed. Conventional D-LDO suffers from a ringing problem when settling the output voltage at a large load transition, which increases the settling time. The proposed D-LDO removes the ringing and reduces the settling time using an auxiliary power stage which adjusts its output current to a load current in the transient state. It also achieves a low output ripple voltage using a comparator with a complete comparison signal. The proposed D-LDO was fabricated using a 65-nm CMOS process with an area of 0.0056 μ㎡. The undershoot and overshoot were 47 mV and 23 mV, respectively, when the load current was changed from 10 mA to 100 mA within an edge time of 20 ns. The settling time decreased from 2.1 ㎲ to 130 ns and the ripple voltage was 3 mV with a quiescent current of 75 ㎂.