• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.6
• /
• pp.608-614
• /
• 2023

The fast filling process of high-pressure hydrogen has an important impact on the filling efficiency and safety. In this paper, a specific study is carried out on the thermophysical phenomena during the fast filling process. Starting from the gas state equation of hydrogen, the change law of the hydrogen storage temperature is obtained, and then the temperature rise prediction is constructed. The model can clarify the relationship between the filling parameters and the temperature rise during the fast filling process, thereby revealing the flow and heat transfer laws of the fast charging process. To improve the theoretical research basis for the evaluation of vehicle-mounted hydrogen fast charging capacity, temperature prediction and optimization of hydrogenation methods.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.353-358
• /
• 2010

High pressure gas is a widely used storage mode for hydrogen fuel. A typical hydrogen tank that is charged with hydrogen gas can function as a hydrogen supply source in a large number of applications. The filling process of a high-pressure hydrogen tank should be reasonably short. However, when the fill time is short, the maximum temperature in the tank increases. Therefore the process should be designed in such a way to avoid high temperatures in the tank because of safety reasons. The paper simulates the fast filling process of hydrogen tanks using Computational Fluid Dynamics method. The local temperature distribution in the tank is obtained. Results obtained are compared with available experimental data. Further work is going on to improve the accuracy of the calculations.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.36 no.1
• /
• pp.34-40
• /
• 1991

The study aimed to investigate the relationship between the rates of leaf senescence and photosynthate translocation at post-anthesis. Seven barley varieties were observed at Suweon in 1988-89. The varieties differed significantly in the number of leaves survived and the rate of photosynthate transolcation with the progress of grain filling. The rate of grain filling was higher in the fast leaf sene-scencing varieties than the slow senescencing ones. There was a close coincidence between the rates of grain filling and $\^$14/c translocation into grains. Photosynthesis was higher in the fast leaf senescencing varieties at early stage of grain filling, but the reverse phenomenon was observed at the late stage of grain filling. The grain yield of fast senescencing varieties was higher than that of slow ones.

• Korean Journal of Remote Sensing
• /
• v.37 no.4
• /
• pp.777-788
• /
• 2021

Since aerosol has a relatively short duration and significant spatial variation, satellite observations become more important for the spatially and temporally continuous quantification of aerosol. However, optical remote sensing has the disadvantage that it cannot detect AOD (Aerosol Optical Depth) for the regions covered by clouds or the regions with extremely high concentrations. Such missing values can increase the data uncertainty in the analyses of the Earth's environment. This paper presents a spatial gap-filling framework using a univariate statistical method such as DCT-PLS (Discrete Cosine Transform-based Penalized Least Square Regression) and FMM (Fast Matching Method) inpainting. We conducted a feasibility test for the hourly AOD product from AHI (Advanced Himawari Imager) between January 1 and December 31, 2019, and compared the accuracy statistics of the two spatial gap-filling methods. When the null-pixel area is not very large (null-pixel ratio < 0.6), the validation statistics of DCT-PLS and FMM techniques showed high accuracy of CC=0.988 (MAE=0.020) and CC=0.980 (MAE=0.028), respectively. Together with the AI-based gap-filling method using extra explanatory variables, the DCT-PLS and FMM techniques can be tested for the low-resolution images from the AMI (Advanced Meteorological Imager) of GK2A (Geostationary Korea Multi-purpose Satellite 2A), GEMS (Geostationary Environment Monitoring Spectrometer) and GOCI2 (Geostationary Ocean Color Imager) of GK2B (Geostationary Korea Multi-purpose Satellite 2B) and the high-resolution images from the CAS500 (Compact Advanced Satellite) series soon.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.5
• /
• pp.1951-1972
• /
• 2018

Wi-Fi Access Point (AP) optimization approaches are used in indoor positioning systems for signal coverage enhancement, as well as positioning precision improvement. Although the huge power consumption of the AP optimization forms a serious problem due to the signal coverage requirement for large-scale indoor environment, the conventional approaches treat the problem of power consumption independent from the design of indoor positioning systems. This paper proposes a new Fast Water-filling algorithm Group Power Constraint (FWA-GPC) based Wi-Fi AP optimization approach for indoor positioning in which the power consumed by the AP optimization is significantly considered. This paper has three contributions. First, it is not restricted to conventional concept of one AP for one candidate AP location, but considered spare APs once the active APs break off. Second, it utilizes the concept of water-filling model from adaptive channel power allocation to calculate the number of APs for each candidate AP location by maximizing the location fingerprint discrimination. Third, it uses a fast version, namely Fast Water-filling algorithm, to search for the optimal solution efficiently. The experimental results conducted in two typical indoor Wi-Fi environments prove that the proposed FWA-GPC performs better than the conventional AP optimization approaches.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.48 no.5
• /
• pp.397-401
• /
• 2003

This experiment was conducted to know the characteristics of kernel growth as affected by various temperature regimes during grain filling using the varieties Hwaseongbyeo, Ilpumbyeo and Chucheongbyeo. The rice plants tested were grown in the natural condition at 1/5000a Wagner pots until flowering. After flowering, the rice plants were moved to controlled temperature conditions in a phytotron. The minimum/maximum daily temperature in the phytotron was controlled by 12/18, 15/21, 18/24, 21/27, and 24/$30^{\circ}C$, respectively. The grain weights were measured every three days after treatment. The mean daily kernel growth rate during active grain filling period showed different responses among varieties under various temperature regimes. The kernel growth rate of Chucheongbyeo was seriously reduced as temperature regimes were decreased. However, that of Ilpumbyeo was not influenced so critically. Ilpumbyeo showed some advantages in grain filling under low temperature regimes compared to Chucheongbyeo. The lag phase in grain filling of Chucheongbyeo was the longest among tested varieties, followed by Hwaseongbyeo under daily mean temperature regime of $15^{\circ}C$. Kernel weight of Ilpumbyeo increased fast in early grain filling phase under low temperature. This characteristic may be favorable for grain filling in temperate zone where the daily mean temperature is drastically dropped during grain filling period. Regression analysis with kernel growth rate and temperature showed the estimated critical low temperature for grain filling among varieties were $9^{\circ}C$, $12^{\circ}C$, $13^{\circ}C$ in Ilpumbyeo, Hwaseongbyeo and Chucheongbyeo, respectively. Under moderate temperature the duration of grain filling of Ilpumbyeo was longer than that of Chucheongbyeo. However, Under low temperature that of Ilpumbyeo was more favorable than Chucheongbyeo.

• Journal of the Korean Society of Radiology
• /
• v.10 no.2
• /
• pp.117-124
• /
• 2016

The purpose of this study was tried to evaluate the filling sodium states inside the fuel rod of sodium-cooled fast reactor by digital medical X-ray. We used the diagnostic X-ray generators in digital radiography (DR). This study have found the optimal conditions by changing the effective focal spot size of X-ray tube and post-processing of the DR method with a tungsten edge plate in order to ensure excellent sharpness At this time, the sharpness and resolution were evaluated using the MTF (modulation transfer function). As a result, this study obtained a spatial resolution of 3.871 lp/mm (0.1 MTF), 3.290 lp/mm (0.5 MTF) when implemented the contrast strengthen post-processing in small focal spot. In this research, the result is able to evaluate the level of sodium inside the fuel rod by using the diagnostic X-ray generators in medical digital radiographic images.

• Korean Journal of Breeding Science
• /
• v.40 no.3
• /
• pp.291-294
• /
• 2008

Amylogram properties such as peak viscosity, hot viscosity, cool viscosity, breakdown, pasting consistency and setback were investigated by the Rapid Visco Analyzer and interpreted by the relationship among amylogram properties according to the varietal groups classified by the rapidity of grain filling (RGF) which was calculated by the percentage of grain weight at 15 days after heading to 40 days after heading. The 164 rice recombinant inbred lines from the cross of Milyang23 and Gihobyeo were used to get the basic information regarding the amylogram properties. The used recombinant inbred lines could be grouped into 4 varietal groups such as slow maturing (less than 40% of RGF), mid-slow maturing (41-60% of RGF),mid-fast maturing (61-80% of RGF), and fast maturing (more than 81% of RGF) groups based on the RGF. The peak viscosity and setback showed regular tendency according to the varietal groups classified by the RGF. Positive significant correlations were found between pasting consistency and setback, however negative significant correlations were found between breakdown and setback in all varietal groups.

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.583-588
• /
• 1999

The characteristics of copper thin films and pattern filling capability were investigated by ECD. Prior to deposition of copper film, seed-Cu/Ta(TaN)/$SIO_2$(BPSG)/Si structure was manufactured. Copper deposition was performed with various current waveforms(DC/PC, 1~10,000Hz) and current densities(10~60 mA/$\textrm{cm}^2$) after pretreatment (Oxident removal, wetting) of seed-layer. Conformal pattern filling was performed using PC method with fast deposition rate of 6,000~8,000$\AA$/min. Heat-treated($450^{\circ}C$, 30min) copper films showed good resistivities of 1.8~2.1$\mu$$\Omega$.cm. According to the XRD analysis, (111)-preferred orientation of copper film was found in ECD-Cu/seed-Cu/Ta/$Sio_2$/Si structure. Also, we have successfully achieved to fill via holes with 0.35$\mu\textrm{m}$ width and 4:1 aspect ratio.

• Textile Coloration and Finishing
• /
• v.12 no.1
• /
• pp.1-11
• /
• 2000

This paper surveys the fabric weavability and machine efficiency in the various weaving looms such as Projectile, Rapiers, and Air-jet. Used projectile loom was Sulzer-PU, and FAST-R, THEMA-11E, and Picanol-GTX were used for Rapier looms, as the Air-Jet looms, Picanol PAT and OMNI types were used. Using these looms, 5 harness worsted satin fabrics were woven for surveying the fabric weavability and machine efficiency. Warp yam count of fabric is 1/40Nm, Sirofil, and filling is 1/30 Nm, worsted. End breaks of warp and filling directions for the various types of looms are measured and discussed with the mechanism of each loom. Warp and filling yam tensions are also measured and analysed with open width of shedding motion of each weaving machine. And various warp yam tensions with open width of shedding are measured and analysed according to the warp yam in various heald frame. These results fire also discussed with temples such as bar and ring. Warp yam tensions at the various positions on the fabric with various looms are measured and discussed with fabric mechanical properties such as tensile, bending, shear and surface.