• Transactions on Electrical and Electronic Materials
• /
• 제12권5호
• /
• pp.204-208
• /
• 2011

In this paper, the design area of a fabricated solar cell has been analyzed with respect to its charge density. The mathematical calculation used for charge-density derivation was obtained from the 2001 version of a MATHCAD program. The parameter range for the calculations was ${\pm}1{\times}10^{17}cm^{-3}$, which is in the normal parameter range for n-type doping impurities ($7.0{\times}10^{17}cm^{-3}$) and also for p-type impurities ($4.0{\times}10^{17}cm^{-3}$). Therefore, it can be said that the fabricated solar-cell design area has a direct effect on charge-density changes.

• 한국정보처리학회논문지
• /
• 제6권5호
• /
• pp.1351-1361
• /
• 1999

The wide spread of multimedia system demands a large area viewing display device which can inform a message to many people in open area. This paper is about the design of a large area viewing LED panel control system. The control system runs on 16 bit microprocessor MC68EC000 and has following functions: 16 line clock and time, 2 channel priority interrupt, 2 channel direct memory access, 2 channel 12 bit clock and timer, 2 channel infrared remocon receiver, 2 channel RS-232C with 16 byte FIFO, IBM PC/AT compatible keyboard interface, ISA bus, battery backuped real time clock, battery backuped 256 byte SRAM and watch dog timer. The core circuits are implemented to ASIC, considering lower cost, higher reliability, higher performance, smaller dimension, and lower power consumption. This is verified by simulation and fabricated in 0.6 um CMOS SOG processes. The total gate count is 39,083 and the clock frequency is 48 MGz. The fabricated ASIC is mounted on test board.

• Current Photovoltaic Research
• /
• 제11권3호
• /
• pp.75-78
• /
• 2023

Recently, the installation of photovoltaic modules in urban areas has been increasing. In particular, the demand for solar modules installed in a limited space is increasing. However, since the crystalline silicon solar module's size is proportional to the solar cell's size, it is difficult to manufacture a module that can be installed in a limited area. In this study, we fabricated a solar module with a shingled design that can control horizontal and vertical width using a bi-directional laser scribing method. We fabricated a string cell with a width of 1/5 compared to the existing shingled design string cells using a bi-directional laser scribing method, and we fabricated a solar module by connecting three strings in parallel. Finally, we achieved a conversion power of 5.521 W at a 103 mm × 320 mm area.

• Smart Structures and Systems
• /
• 제7권1호
• /
• pp.1-13
• /
• 2011

It has been shown in the literature that active adjustment of the intake area of a jet engine has potential to improve its fuel efficiency. This paper presents the design and control of a novel proof-of-concept active jet engine intake using Nickel-Titanium (Ni-Ti or Nitinol) shape memory alloy (SMA) wire actuators. The Nitinol SMA material is used in this research due to its advantages of high power-to-weight ratio and electrical resistive actuation. The Nitinol SMA material can be fabricated into a variety of shapes, such as strips, foils, rods and wires. In this paper, SMA wires are used due to its ability to generate a large strain: up to 6% for repeated operations. The proposed proof-of-concept engine intake employs overlapping leaves in a concentric configuration. Each leaf is mounted on a supporting bar than can rotate. The supporting bars are actuated by an SMA wire actuator in a ring configuration. Electrical resistive heating is used to actuate the SMA wire actuator and rotate the supporting bars. To enable feedback control, a laser range sensor is used to detect the movement of a leaf and therefore the radius of the intake area. Due to the hysteresis, an inherent nonlinear phenomenon associated with SMAs, a nonlinear robust controller is used to control the SMA actuators. The control design uses the sliding-mode approach and can compensate the nonlinearities associated with the SMA actuator. A proof-of-concept model is fabricated and its feedback control experiments show that the intake area can be precisely controlled using the SMA wire actuator and has the ability to reduce the area up to 25%. The experiments demonstrate the feasibility of engine intake area control using an SMA wire actuator under the proposed design.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제51권12호
• /
• pp.596-603
• /
• 2002

New layout methods for implementing MOS switches of ultra low channel resistance are presented. These area-effective layout methods include the waffle structure, zipper structure, star zag structure and fingered waffle structure. The design equations for these new layout structures are analyzed. The area-effectiveness of these structures is compared with that of the conventional alternating bar structure. MOS switches of the waffle structure were fabricated using a standard 0.25um CMOS process. The experimental characterization results of the fabricated MOS switches are presented. The analytical comparison and experimental results show that area reductions over 40% are achievable with the new structures.

• Journal of Radiation Protection and Research
• /
• 제34권2호
• /
• pp.77-81
• /
• 2009

An Area Radiation Monitoring System (ARMS) ionization chamber, which had an 11.8 L active volume, was fabricated and performance-tested at KAERI. Low leakage currents, linearities at low and high dose rates were achieved from performance tests. The correlation coefficients between the ionization currents and the dose rates are 1 at high dose rate and 0.99 at low dose rate. In this study, an integration-type ARMS ionization chamber was tested over a year for an evaluation of its long-term stability at a radioisotope (RI) repository of the Young-gwang nuclear power plant. The standard deviation of dose rate of 1 day data and over a 100-days mean value were 6.2 $\mu$R/h and 2.9 $\mu$R/h, respectively. The fabricated ARMS ionization chamber showed stable performance from the results of the long-term tests. Design and performance characteristics of the fabricated ionization chamber for the ARMS from performance-tests are also addressed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.373-378
• /
• 2004

Recently the electrostatic 2-axis MEMS stages have been fabricated for the purpose of an application to PSD (Probebased Storage Device). However, most of them have low area efficiency, which is undesirable as data storage devices, since all of the components (springs, comb electrodes, anchors, platform, etc.) are placed in-plane. In this paper, we present a novel structure of electrostatic 2-axis MEMS stage that is characterized by having large area platform. For large area efficiency, the actuator part consisting of mainly comb electrodes and springs is placed right below the platform. In this article, the structures and operational principle of the MEMS stages are described, followed by design procedure, structural and modal analysis using FEM(Finite Element Method). The area efficiency of the MEMS stage was designed to be about 55％, that is very large compared with conventional ones having a few percentage.

• Journal of Mechanical Science and Technology
• /
• 제16권5호
• /
• pp.591-598
• /
• 2002

Leakage magnetic flux is occurred in the cracked area of magnetized specimens, and also it changes the magnetic domain area of the magneto-optical film positioned on the specimen. It causes the change of the optical permeability of the magnetic domain on the crack area. So crack images can be obtained easily using this principle. On the other hand, utilizing a laser in this method makes possible to perform a remote sensing by detecting the light intensity contrast between cracked area and normal area. This paper shows the application of non-destructive inspection system taking advantage of magneto-optical method for micro-cracks and presents examples applied to the several types of specimens having fatigue cracks and fabricated cracks using this method. Also the authors prove the possibility of this method as a remote sensing system under the oscillation load considering application to real fields.

• 한국전산구조공학회논문집
• /
• 제35권1호
• /
• pp.45-55
• /
• 2022

현 설계기준에서 제시한 단부횡보강 상세는 시공성과 생산품질이 현저히 떨어지므로 내진성능과 시공성을 확보할 수 있는 RC 구조벽체의 단부횡보강 상세 개발이 필요하다. 최근 선재 제작기술의 발전으로 다양한 선조립철근의 제작이 가능해지고 있으며 특히 다양한 연속횡보강 철근 상세의 제작이 가능하게 되었다. 본 연구에서는 사각 연속횡보강 선조립철근 단부횡보강 상세를 적용한 RC 구조벽체의 모멘트-곡률 관계에 대한 분석을 진행하였다. 비선형 단면해석에 의하면 사각 연속횡보강의 상세를 적용한 RC 구조벽체는 사각 연속횡보강 영역의 면적이 증가할수록 내진성능을 확보할 수 있다. 이러한 연구결과에 근거하여 사각 연속횡보강 선조립 철근의 상세 적용시, 단부횡보강 영역의 면적만큼 사각 연속횡보강 영역의 면적을 확보해야 한다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.337-338
• /
• 2012