• 대한의용생체공학회:의공학회지
• /
• 제35권5호
• /
• pp.125-131
• /
• 2014

The purpose of this study is to verify the utility of reflected photoplethysmography sensor using two green light emitting diodes that influenced by ambient light. Recently it has been studied that green light emitting diode is suitable for light source of reflected photoplethysmography sensor at low temperature and high temperature. Another study showed that, green light is better for monitoring heart rate during motion than led light. However, it has a bad characteristic about ambient light noise. To verify the utility of reflected photoplethysmography sensor using green light emitting diode, this study measures the photoplethysmography signal that is distorted by ambient light and will propose a solution. This study has two parts of research method. One is measurement system that composed sensor and board. The sensor is made up PE-foam and Non-woven fabric for flexible sensor. The photoplethysmography signal is measured by measurement board that composed high-pass filter, low-pass filter and amplifier. Ambient light source is light bulb and white light emitting diode that has three steps brightness. Photoplethysmography signal is measured with lead II electrocardiography signal at the same time and it is measured at the finger and radial artery for 1 minute, 1000 Hz sampling rate. The lead II electrocardiography signal is a standard signal for heart rate and photoplethysmography signal that measured at the finger is a standard signal for waveform. The test is repeated 3 times using three sensor. The data is processed by MATLAB to verify the utility by comparing the correlation coefficient score and heart rate. The photoplethysmography sensor using two green light emitting diodes is shown better utility than using one green light emitting diode and red light emitting diode at the ambient light. The waveform and heart rate that measured by two green light emitting diodes are more identical than others. The amount of electricity used is less than red light emitting diode and error peak detectability factor is the lowest.

• 한국환경과학회지
• /
• 제13권3호
• /
• pp.223-232
• /
• 2004

The change of pressure drop according to the change in the inlet concentration, pulse interval, and injection distance of pulse air jet type bag filters, and the effect of venturi installation are as follows. The pressure drop with the range of 30 to $50mmH_2O$ varies according to the injection distance with 30, 50, 70, 90sec and the inlet concentration of venture built-in fabric filters. For the lower concentration of 0.5g/㎥ and 1g/㎥, the pressure $drop(\DeltaP)$ was stable 60 to 90minutes after operation. For the higher concentration of 3g/㎥, as $\DeltaP$ continues to go up, pulse interval should be set shorter than 30 seconds. The pressure drop with the injection distance of 1l0mm, when inlet dust concentration is 0.5g/㎥ or 1g/㎥, is 1.3 to 2 lower than with the injection distance of 50, 160, and 220mm, which means that the inflow amount of the secondary air by the instant acceleration is large. The injection distance of 2g/㎥ and 3g/㎥ has the similar pressure distribution. The higher inlet concentration is, the more important pulse interval is than injection distance. The pressure drop has proved to be larger when inlet concentration is lower and injection distance closer, on condition that the venturi is installed. The change in the pressure drop was smallest when injection distance was 50mm, followed by 220mm, 160mm, and 110mm.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.281-292
• /
• 2008

Prefabricated Board Drains (PBDs) recently become more widely used than conventional sand drains in improving soft ground because the PBD is more time and cost effective. The performance of PBDs is affected by disturbance in the adjacent soil formation during inserting mandrels, the intrusion of fine particles into filter fabric, and necking of the drain by excessive lateral pressure especially occurring in very deep clay formation such as the Busan New Port site. In this study, the PBD with double-core is introduced, which seems to overcome the shortcomings of usual single-core PBDs. An in-situ test program was established in the Busan New Port site, in which a set of the double-core PBDs and the single-core PBDs was installed to compare the efficiency of each of the drains. The discharge capacity of the double-core and the single-core PBDs was compared for various confining pressures in the modified Delft test and the chamber test. A series of CRS consolidation tests was performed in order to obtain profiles of void ratio-effective stress and void ratio-permeability relationships in the Busan New Port site that are used as input date in performing a numerical program ILLICON. The numerically simulated settlements of ground surface in the test site are in good agreement with those of in-situ measurements. In addition, the performance of the double-core and single-core PBDs has been experimentally and numerically compared in this paper.

• 한국가스학회지
• /
• 제25권6호
• /
• pp.29-34
• /
• 2021

제약회사에서 제조하는 의약품의 원재료에 인화성물질이 종종 존재한다. 이런 경우 과량의 인화성 물질을 투입하여 중간체를 만들고 반응에 참여하지 않은 인화성물질을 여과 및 건조단계를 통하여 제거하는 공정을 거치게 된다. 또한, 여과 공정에서 분리된 인화성 액체가 여액받이 통에 스플래쉬 필링 형태로 쌓이게 된다. 이런 경우 인화성 액체의 증기 및 미스트가 생성되어 폭발 하한 값, 최소점화에너지가 더욱 낮아지게 되며 복합 대전이 발생하여 화재·폭발의 위험이 증대된다. 본 연구에서는 최근의 제약회사 여과공정 중 발생한 화재 사고를 분석하여, 화재 폭발 사고를 방지하기 위한 방안으로 질소 공급설비 설치, 용량 개선, 도전성 여과포 및 정전기 축적 방지대책 등을 제시하고자 한다.

• 대한환경공학회지
• /
• 제31권1호
• /
• pp.21-28
• /
• 2009

Ca계 및 Na계 탈황제를 대상으로 열중량 분석실험과 승온탈리 실험을 수행하여 탈황제의 열적안정성, 집진기 전단 온도인 $250^{\circ}C$에서 탈황 성능, 그리고 상온에서 흡수용량 등을 비교하여 아래와 같은 결론을 도출하였다. 소석회($Ca(OH)_2$)는 약 $390^{\circ}C$에서 열 분해되기 시작하여 480~$500^{\circ}C$에 이르면 완전하게 분해되었다. 열분해 결과 생성된 생석회(CaO)의 무게는 최초 소석회 무게의 76%로 감소하였다. 중탄산나트륨($NaHCO_3$)은 약 $95^{\circ}C$에서부터 분해되기 시작하여 $190^{\circ}C$ 이하의 온도에서 완전하게 분해되어 처음 도입된 중탄산나트륨 무게와 비교하여 약 63%로 감소하였다. $250^{\circ}C$에서 실시한 열중량 분석 결과, 무수탄산나트륨($Na_2CO_3$)의 경우에는 탈황제 무게의 35%에 해당하는 $SO_2$를 흡수할 수 있고, 생석회는 15.6%, 소석회는 6.5%까지 $SO_2$를 흡수할 수 있는 것으로 나타났다. $250^{\circ}C$에서 초기반응 속도를 비교하면, Ca계 탈황제의 경우에는 초기 미반응 시간이 있는 반면에 Na계 탈황제인 무수탄산나트륨에서는 이러한 초기 미반응 시간이 없어, Ca계 반응제의 경우보다 Na계 탈황제의 경우에 $SO_2$와 더 빠른 반응이 진행되었다. 상온에서 실시한 승온탈리 실험 결과, Na계인 무수탄산나트륨보다는 Ca계인 소석회가 더 많은 $SO_2$를 흡수하였다. 따라서 저온에서는 Ca계인 소석회가 적절하고 고온에서는 무수탄산나트륨이 더 적절한 탈황제인 것으로 판단된다.