• 한국분말재료학회지
• /
• 제22권3호
• /
• pp.181-186
• /
• 2015

In this study, the effect of the friction stir welding (FSW) was compared with that of the gas tungsten arc welding (GTAW) on the microstructure and microhardness of Cu-Ni alloy weldment. The weldment of 10 mm thickness was fabricated by FSW and GTAW, respectively. Both weldments were compared with each other by optical microstructure, microhardness test and grain size measurement. Results of this study suggest that the microhardness decreased from the base metal (BM) to the heat affected zone (HAZ) and increased at fusion zone (FZ) of GTAW and stir zone (SZ) of FSW. the minimum Hv value of both weldment was obtained at HAZ, respectively, which represents the softening zone, whereas Hv value of FSW weldment was little higher than that of GTAW weldment. These phenomena can be explained by the grain size difference between HAZs of each weldment. Grain size was increased at the HAZ during FSW and GTAW. Because FSW is a solid-state joining process obtaining the lower heat-input generated by rotating shoulder than heat generated in the arc of GTAW.

• 동력기계공학회지
• /
• 제21권5호
• /
• pp.86-91
• /
• 2017

Friction Stir Welding (FSW) is useful technique to join aluminum alloy with energy efficient and environment friendly. In this paper, the design of experiment with three-way factorial design was adopted for optimum conditions of welding variables in the FSW of Al 6061 alloy. Tools of shoulder diameter of 9, 12, 15 mm and pin length of 1.5 mm were used. Also the material's dimension for welding were $2{\times}100{\times}150mm$, and the tensile specimens were worked by water-jet technique. Welding variables were shoulder diameter, rotating speed and travel speed of tool. From the results of this work, the welding factor influenced on yield strength most was travel speed and the optimum condition for FSW was predicted as the shoulder diameter of 15 mm, welding speed of 500 mm/min and rotating speed of 2,000 rpm. Also the presumption range of yield strength at optimal condition of reliability 99% was estimated to $207.19{\pm}9.91MPa$.

• Journal of Welding and Joining
• /
• 제27권5호
• /
• pp.81-87
• /
• 2009

Recently, extruded aluminium-alloy panels have been used in the car bodies for the purpose of the light-weight of railway vehicles and FSW(Friction Stir Welding), which is superior to the arc weldings, has been applied in the railway vehicles. This paper presents the optimum design of the FSW process on A6005 extruded alloy for railway vehicles to improve its mechanical properties. Rotational speed, welding speed and tilting angle of the tool tip were chosen as design parameters. Three objective functions were determined; maximizing the tensile strength, minimizing the hardness and maximizing the difference between the normalized tensile strength and hardness. The tensile tests and the hardness tests for fifteen FSW experiments were carried out according to the central composite design table. Recursive model functions on three characteristic values, such as the tensile strength, the hardness difference(${\Delta}Hv$) and the difference of normalized tensile strength and ${\Delta}Hv$, were estimated according to the classical response surface analysis methodology. The reliability of each recursive function was verified by F-test using the analysis of variance table. Sensitivity analysis on each characteristic value was done. Finally, the optimum values of three design parameters were found using Sequential Quadratic Programming algorithm.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.700-707
• /
• 2013

Owing to high oil prices and environmental issues, the automobile industry has conducted considerable research and made large investments to manufacture a high-efficiency automobiles. In the case of automobile wheels in which a lightweight material is used to increase the fuel efficiency a mold is used to increase the production efficiency; however, the use of the molding method for this purpose is very expensive. Therefore an automobile wheel consists of two parts. In this study a two-piece automobile wheel is manufactured by the friction stir welding(FSW) of Al6061-T6 to reduce the manufacturing cost and process complexity. The FSW welding tool geometry and rotational speed, and the feed rate are key factors that significantly affect the weld strength. Therefore tensile tests were conducted on specimens produced using various welding conditions, and the optimal FSW welding conditions were applied to manufacture aluminum wheels. To ensure reliability, prototype aluminum wheels were manufactured and their mechanical reliability and safety were evaluated using a durability test, fatigue durability test, and impact test. Through this study, aluminum wheel production was made possible using the FSW method.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.493-498
• /
• 2002

Friction stir welding (FSW) is a relatively new solid-state joining process which can homogenize the heterogeneous microstructure by intensely plastic deformation arising from the rotation of the welding tool. The present study applied the FSW to an A356 aluminum (AI) alloy with the as-cast heterogeneous microstructure in the T6 temper condition, and examined an effect of microstructure on mechanical properties in the weld. The base material consisted of Al matrix with a high density of strengthening precipitates, large eutectic silicon and a lot of porosities. The FSW led to fragment of the eutectic silicon, extinction of the porosities and dissolution of the strengthening precipitates in the Al alloy. The dissolution of strengthening precipitates reduced the hardness of the weld around the weld center and the transverse ultimate tensile strength of the weld. Longitudinal tensile specimen containing only the stir zone showed the roughly same strength as the base material and a much larger elongation. Moreover, Charpy impact tests indicated that the stir zone had remarkably the higher absorbed energy than the base material. The higher mechanical properties of the stir zone were attributed to a homogenization of the as-cast heterogeneous microstructure by FSW.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권4호
• /
• pp.791-796
• /
• 2001

Friction stir welding is a solid phase welding process that does not melt the metal when welding. The FSW is the most remarkable and potentially useful new welding technique that is still in development. Friction stir butt welding process on 2 mm thick Al 1050 plates by utilizing a milling machine was experimentally studied. With the optimized heat generating tool welds could be achieved that are void and crack free. It was found that the friction stir welded tensile test specimens failed in the HAZ outside of the weld metal, and that the tensile strength was above 90% of that of the base metal.

• 한국산학기술학회논문지
• /
• 제19권3호
• /
• pp.614-618
• /
• 2018

Al 6061-T6를 사용하여 마찰교반 용접 시 회전 툴 숄더의 너비부의 넓이와 회전 속도, 이동속도의 변화에 따른 물성의 변화에 대하여 평가되었다. FSW 공정의 접합 변수에 따라 인장시험을 수행하기 위하여 KS B 0801 5호에 따라 시험편을 제작하여 마찰교반 용접을 시행하였다. 마찰교반 용접이 된 시험편의 기계적 특성을 평가하기 위해 Instron 인장시험기를 사용하여 1mm/min의 시험 속도로 인장시험을 시행했다. 평가결과, 인장강도는 회전 속도가 증가함에 증가 하였다. 툴 숄더의 이동 속도가 빠를수록 툴 유형에 관계없이 인장강도는 감소하였다. 툴 숄더 직경 12 mm (TSD12) 의 인장 강도 값은 일반적으로 8mm 보다 높게 나타났다. 이동 속도와 회전하는 속도가 한계 값을 초과하면 재료의 특성에 영향을 주지 않고 안정화 단계에 도달한다. 툴 숄더 직경 8mm (TSD8) 는 TSD12 유형의 공구와 비교하여 재료 특성이 감소하고 용접 영역에서 재료가 완전히 혼합되지 않는다. 인장 강도 값은 모든 회전 속도 1500 rpm에서 상대적으로 감소한다. 이동 속도가 낮을수록 같은 회전수에서 재료의 혼합될 수 있는 양이 많으므로 인장강도값이 높게 나타난다. 결과적으로 용접 영역에서 재료를 완전히 혼합하고 전이 온도에 도달하기 위해서는 임계값을 초과하는 회전 속도가 필요하다.

• 대한금속재료학회지
• /
• 제48권6호
• /
• pp.533-542
• /
• 2010

The specific motivation for joining an Al alloy and Zn-coated steel arises from the need to save fuel consumption by weight reduction and to enhance the durability of vehicle structures in the automobile industry. In this study, the lap joining A6K31 Al alloy (top) and SGARC340 Zn-coated steel (bottom) sheets with a thickness of 1.0 mm and 0.8 mm, respectively, was carried out using the friction stir weld (FSW) technique. The probe of a tool did not contact the surface of the lower Zn-coated steel sheet. The friction stir welding was carried out at rotation speeds of 1500 rpm and travel speeds of 80~200 mm/min. The effects of tool geometry and welding speed on the mechanical properties and the structure of a joint were investigated. The tensile properties for the joints welded with a larger tool were better than those for the joints done with a smaller tool. A good correlation between the tensile load and area of the welded region were observed. The bond strength using a larger tool (M4 and M3) decreased with an increase in welding speed. Most fractures occurred along the interface between the Zn-coated steel and the Al alloy. However, in certain conditions with a lower welding speed, fractures occurred at the A6K31 Al alloy.

• 동력기계공학회지
• /
• 제15권2호
• /
• pp.61-68
• /
• 2011

This paper investigates the tensile properties of the friction stir welded joints of Al 7075-T651 aluminum plate according to the welding conditions. A 7075-T651 aluminum alloy plate with a thickness of 6.0 mm was used in this investigation. For the friction stir welding (FSW) process, a tool with shoulder diameter of 20 mm and probe diameter of 9 mm was used. The rotation speed and traverse speed conditions were changed in this study, the other welding conditions are constant. The welding direction was aligned with the material rolling direction, and dimension of the FSW plate were $250{\times}100{\times}6\;mm$. As far as this work is concerned, the optimal FSW conditions are determined as the rotation speed, 600 rpm and traverse speed 0.8 mm/sec or the rotation speed, 800 rpm and traverse speed 0.5 mm/sec.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.159-161
• /
• 2004

FSW공전은 특수하게 설계된 용접툴(tool)을 특정한 회전수로 회전시키면서 용접하고자하는 재료의 용접라인에 삽입하여 용접에 필요한 마찰열과 소성변형을 발생시키고, 그 후 용접라인을 따라 툴을 이동시킴으로써 용접이 이루어지는 매우 간단한 공정이다. (중략)