• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.6
• /
• pp.63-71
• /
• 1998

In this paper, we experiment the characteristics of coupling coefficient, gain, diffraction efficiency and dependence of time determined by TWM(Two-Wave Mixing), using Fe-LiNbO$_3$ crystal(doped with 0.015Wt.%). From these results, we proposed to apply for optical memory application. The highest coupling angle of 14。 and maximum coupling coefficient of 6.9$cm^{-1}$ / are obtained at 514.5nm wavelength. Also, maximum diffraction efficiency is 54.13% when intensity ratio and writing beam incident angle are 0.1 and 14o, respectively. After fixing process, diffraction efficiency is 21.4%. As an example, we demonstrated the writing and reconstruct optical data using spatial light modualtor and angular multiplexing in most optimal condition.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.5
• /
• pp.345-352
• /
• 2017

In this study, squeal noise with respect to pressure variation is measured by a lab-scaled brake dynamometer and estimated by a complex finite element (FE) eigenvalue analysis. From the FE eigenvalue sensitivity analysis, unstable frequencies occur due to a mode-coupling mechanism and are found to change with variation in contact stiffness. In the experiment, squeal frequencies near 1 kHz, 2.5 kHz, 3.5 kHz, and 4 kHz are increased with pressure variation. The sensitivity of squeal modes to contact stiffness variation obtained from the FE analysis is shown to approximate the variation of squeal frequencies under pressure variation in the experiment.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.389-393
• /
• 2000

Effects of Co addition and heat treatment on the magnetic properties of Fe-Si-B thin films were investigated. The compositions of metalloids, i.e, B and Si, in the alloys were kept 10 at.% each. Heat treatments were carried out in the temperature range from 100 to $300^{\circ}C$ for up to 60 min. Amorphous thin films of FeCoSiB were deposited on the water-cooled substrates by dc magnetron sputtering. The composition of thin films was controlled by placing proper number of pellets of alloying elements and analyzed by ICP, resulting in $Fe_{80-X}Co_ XB_{10}Si_{10}$ (X=8~18 at.%). Saturation magnetization of the alloys increased as Co concentration increased up to 10 at.% and then decreased with further increase of Co concentration. However, coercive force of the films decreased with the increase of Co concentration. Furthermore, the coercive force was also reduced by the annealing due to the residual stress relief.

• Journal of the Korean Vacuum Society
• /
• v.17 no.3
• /
• pp.220-225
• /
• 2008

In this research, the P(VDF-TrFE) copolymer thin films were prepared by the physical vapor deposition and studied to their piezoelectric properties. In the case of a specimen produced by varying the deposition temperature from $260^{\circ}C$ to $300^{\circ}C$, its piezoelectric coefficient($d_{33}$) increased from 32.3pC/N to 36.28pC/N, and piezoelectric voltage coefficient($g_{33}$) from $793{\times}10^{-3}V{\cdot}m/N$ to $910.5{\times}10^{-3}V{\cdot}m/N$. On the basis of these experimental results, we concluded that the P(VDF-TrFE) copolymer thin film prepared at $300^{\circ}C$ showed the optimum piezoelectric properties. At the deposition temperature of $320^{\circ}C$, its piezoelectric coefficient(d33) decreased 25.3 pC/N and piezoelectric voltage coefficient($g_{33}$) $680{\times}10^{-3}V{\cdot}m/N$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.323-331
• /
• 2010

In this study, we propose a 3D finite element (FE) model for the residual stress under oblique shot peening. Using the FE model for an oblique impact, we examine the effects of factors on the residual stress such as the Rayleigh damping in the material, dynamic friction, and the rate dependency of the material and systematically integrate the effects. The plastic deformation of the shot is also emphasized. Then, the FE model is used to study oblique multi-impacts. The results obtained using the FE model are compared with experimental x-ray diffraction (XRD) results; in contrast to the rigid and elastic shots, plastic shots are found to produce residual stresses similar to that shown in the XRD results. Thus, the 3D FE models with integrated factors and plastically deformable shots are validated. The proposed model will serve as a basis for the 3D FE model for multi-impacts with different impact angles to simulate the actual phenomenon of shot peening.

• Journal of the Korean Magnetics Society
• /
• v.20 no.5
• /
• pp.196-200
• /
• 2010

$\gamma-Fe_2O_3$ nanoparticles have been prepared by a sol-gel method. The structural and magnetic properties have been investigated by XRD, VSM and Mossbauer spectroscopy. $\gamma-Fe_2O_3$ powder annealed at $150^{\circ}C$ has a spinel structure and superparamagnetical behavior. The estimated size of superparammagnetic $\gamma-Fe_2O_3$ nanoparticle is around 7 nm. The hyperfine fields at $-261^{\circ}C$ for the A and B patterns were found to be 503 and 485 kOe, respectively. The blocking temperature ($T_B$) of superparammagnetic $\gamma-Fe_2O_3$ nanoparticle is about $-183^{\circ}C$. The magnetic anisotropy constant of $\gamma-Fe_2O_3$ nanoparticle was calculated to be $1.6{\times}10^6ergs/cm^3$. $\gamma-Fe_2O_3$ nanoparticle annealed at $150^{\circ}C$ can be a candidate for biomedicine applications as magnetic carriers.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.30 no.3
• /
• pp.23-28
• /
• 2022

In order to investigate the degree of sewage sludge dewaterability using Fe(II)/Na₂S₂O₈, STTF, SCST, water content, TS, VS, TB-EPS as carbohydrate and Protein were measured. The dosage of Na₂S₂O₈ was varied from 0.4 to 0.7 mmol/gVS and molar ratio of Fe(II)/Na₂S₂O₈ was varied from 0.5 to 0.7 mol/mol. According to the increase of the dosage of Na₂S₂O₈ and Fe(II)/Na₂S₂O₈ molar ratio, STTF and SCST increased from 1.00 to 15.00 and 4.51, respectively. Water content decreased to 82.6%. TB-EPS as carbohydrate and protein decreasing rate also increased to 37.16% and 57.34%, respectively. Especially, Na₂S₂O₈ 0.6 mmol/gVS and Fe(II)/Na₂S₂O₈ 0.6 mol/mol condition, water content dercreased to 83.1%, STTF and SCST increased to 13.64 and 4.19 which showed the cost effective improvement of dewaterability. It is considered that SO₄^- radical generated by Fe(II)/Na₂S₂O₈ degraded EPS and converted bound water to free water.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.1
• /
• pp.36-41
• /
• 2000

We studied the exchange anisotropy of Ni-Fe/Co-Fe/Mn-Ir/Cu/buffer/Si multilayers using D.C magnetron sputtering technique. Generally, Ni-Fe/Mn-Ir/buffer(Cu)/Si multilayers cannot pin the ferromagnetic layer for the lower exchange biased field. We got $H_{ex}$ ex/ increased by two times, after using Cu/Ta as buffer layer to get larger grain size of Mn-Ir layer and inserting very thin Co-Fe layer between the Ni-Fe layer and the Mn-Ir layer to get improved grain-to-grain epitaxy relation at the interface between Ni-Fe layer and Mn-Ir layer. The variation of $H_{ex}$ by thickness of Mn-Ir layer in ferromagnete/Mn-Ir/buffer/Si multilayers is different to that in Mn-Ir/ferromagnete/buffer/Si multilayers, because the volume distribution of grain size of Mn-Ir layer and the exchange energy at the interface between the Mn-Ir and the ferromagnetic layers is different for stacking sequence.

• Resources Recycling
• /
• v.1 no.1
• /
• pp.44-50
• /
• 1992

The $\alpha$-FeOOH powders were prepared by allkaline and acidic method on the small scale plant from the waste pickling liquor of iron. $\alpha$-FeOOH, $\alpha-Fe_2O_3$, $Fe_3O_4$ and ${\gamma}-Fe_2O_3$ powders were examined by TEM, SEM, TG-DTA, X-ray diffraction, VSM and chemical analysis. The results obtained from the experiment could be summerized as follows : the reaction time for the preparation of $\alpha$-FeOOH was observed to be smaller in the case of alkaline method and the products was acicular with the size of about $0.5\mu\textrm{m}$. The color of $\alpha-FeOOH and $\alpha-Fe_2O_3$was lovely yellow and red, respectively. The magnetic properties of $Fe_3O_4$ obtained by the reduction of $\alpha-Fe_2O_3$in the $H_2$ atomosphere at $370^{\circ}C$ for 1 hour showed 367(Oe) and 82.7(emu/g).

• Resources Recycling
• /
• v.2 no.2
• /
• pp.27-38
• /
• 1993

In this study, we investigated the grinding and sedimentation(elutriation) process of the dusts for the effective separation of high purity iron and iron oxides. For characterization of the dust, particle size distribution and chemical composition, were examined. The results obtained in this study may be summarized as follows : 1. The converter CF(clarifier) dust of the Pohang 1st, 2nd steel making factory and EC(Evaporation Cooler), EP(Eltrostatic precititator) dust of the Kwangyang 2nd steel making factory are composed $\alpha$-Fe(21~50%), FeO(wustite)$Fe_3$$O_4$(magnetite), $Fe_2$$O_3$, CaO, $Al_2$$O_3$, $SiO_2$, and etc. 2. Pure iron has ductile characteristic in nature, particle size of the pure iron increase by increasing the grinding time. On the other hand, it is conformed that bo고 particles of hematite and magnetite become less than 325 mesh after 10 minutes grinding. 3. By applying the elutriation technique for the EC dust of the Kwangyang 2nd steel making factory, the iron powder of high content more than 99.17% of pure Fe was recovered with 37.8% yield at grinding time for 40 minutes. 4. By applying the elutriation technique for the CF dust of the Pohang 2nd steel making factory, the iron powder of high content more than 98.38% of pure Fe was recovered with 44.42% yield at grinding time for 40 minutes. 5. When magnetic separation was performed using plastic bonding magnet of 70 gauss, more than 98% Fe grade of iron powder was recovered in the size range +65 -200 mesh but the recovery of it was low.