• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.21-26
• /
• 2016

This paper presents a step-down DC-DC buck converter with a CCM/DCM dual-mode function for the internal power stage of portable electronic device. The proposed converter that is operated with a high frequency of 1 MHz consists of a power stage and a control block. The power stage has a power MOS transistor, inductor, capacitor, and feedback resistors for the control loop. The control part has a pulse width modulation (PWM) block, error amplifier, ramp generator, and oscillator. In this paper, an external capacitor for compensation has been replaced with a multiplier equivalent CMOS circuit for area reduction of integrated circuits. In addition, the circuit includes protection block, such as over voltage protection (OVP), under voltage lock out (UVLO), and thermal shutdown (TSD) block. The proposed circuit was designed and verified using a $0.18{\mu}m$ CMOS process parameter by Cadence Spectra circuit design program. The SPICE simulation results showed a peak efficiency of 94.8 %, a ripple voltage of 3.29 mV ripple, and a 1.8 V output voltage with supply voltages ranging from 2.7 to 3.3 V.

• Journal of Magnetics
• /
• v.19 no.1
• /
• pp.90-100
• /
• 2014

Position estimation that uses only active phase voltage and current is presented, to perform high accuracy position sensorless control of a SRM drive. By extracting the amplitude of the first switching harmonic terms of phase voltage and current for a PWM period through Fast Fourier Transform (FFT), the flux-linkage and position are estimated without external hardware circuitry, such as a modulator and demodulator, which result in increased cost, as well as large position estimation error, produced when the motional back EMF is ignored near zero speed. A two-phase SRM drive system, consisting of an asymmetrical converter and a conventional closed-loop PI current controller, is utilized to validate the performance of the proposed position estimation scheme in comprehensive operating conditions. It is shown that the estimated values very closely track the actual values, in dynamic simulations and experiments.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.50-61
• /
• 1994

A 300 meter class ROV(CROV300) is composed of three parts : a surface unit, a tether cable and an underwater vehicle. The vehicle controller is based on two processors : an Intel 8097-16-bit one chip micro-processor and a Texas Instruments TMS320E25 digital signal processor. In this paper, the surface controller, the vehicle controller and peripheral devices interfaced with the processors are described. These controllers transmit/receive measured status data and control commands through RS422 serial communication. Depth, heading, trimming, camera tilting, and leakage signals are acquired through the embedded AD converters of the 8097. On the other hand, altitude of ROV and lbstacle avoidance signals are processed by the DSP processor and periodically fetched by the 8097. The processor is interfaced with a 4-channel 12-bit D/A converter to generate control signals for DC motors an dseveral transistors to handle the relays for on/off switching of external devices.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.10 no.3
• /
• pp.64-70
• /
• 1996

In this paper, we designed a low cost data logger system using single chip microcontroller. It detects the normal and abnormal current in distribution system. A sampled analog signals are stored on RAM card(4Mbit) after digitalized by internal A/D converter. Stored data can be transmitted to the personal computer either by internal serial communication port or by external parallel communication port. The transmitted data are analyzed and displayed on personal computer.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1016-1018
• /
• 1992

A numerical model of a three junction device is presented. It allows the simulation of the external characteristics of the PNPN family devices and in this work the simulation of gate turn-off thyristor(GTO) is particularly considered. The proposed PNPN device simulation model solves all the drawbacks presented by the previous work, simulates the GTO well, and fulfills.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1371-1379
• /
• 2013

Application of induction machines in wind turbine driven generators is a good alternative due to their good characteristics such as efficiency, reliability and low cost. Nevertheless, when isolated operation is required, the application of external capacitive bank, connected to the stator windings, to provide self-excitation results in a rather complex analysis. This paper presents an analysis of self-excited induction generator connected to a load either directly or by an intermediate of a power converter. At first a dynamic model of the induction generator accounting for magnetic saturation is developed. Then a number of balanced and unbalanced capacitors, passive and active loads are verified. Experimental results obtained from laboratory tests are compared to those simulated; the two are shown to be in good agreement.

• Journal of Mechanical Science and Technology
• /
• v.18 no.4
• /
• pp.592-596
• /
• 2004

Corrosion is never avoided in the use of materials with various environments. The underwater hull is normally protected against rusting by several coatings of anti-corrosive paint. The purpose of ICCP(Impressed Current Cathodic protection) system is to eliminate the rusting or corrosion, which occurs on metal immersed in seawater. The anode of ICCP system is controlled by an external DC source with converter. The function of anode is to conduct the protective current into seawater. The proposed algorithm includes the harmonic suppression control strategy and the optimum protection strategy and has tried to test the requirement current density for protection, the influence of voltage, the protection potential. This paper was studied the variation of potential and current density with environment factors, time and velocity, and the experimental results will be explained.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.78.3-78
• /
• 2002

In this paper, we present a five-DOF actuator based on dielectric elastomer. The actuator is designed for generating five DOFs motions to drive a micro camera steering module and provides all the functions for controlling CCD array such as focusing, pan and tilting. Basic modeling of the actuator is performed, and simulation works and experimental verifications are conducted, too. The camera steering module includes most parts necessary for driving the actuator such as a micro-controller and DC-DC converter, etc. It can be operated with a personal computer using only communication lines without external power supply. A prototype is developed and its performance is experimentally proved. $\textbullet$ artificial muscle, EAP, actuator.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.369-378
• /
• 1999

This paper presents position control of an electro-hydraulic servo system whoch is operated by four 2-2way high speed on-off valves with either PWM PID control method or sliding mode control method, The advantages of using high speed on-off valves instead of electo-hydraulic servo valves or electro-hydraulic proportional valves are low price robustness for oil contamination and direct control without a D/A converter. The system consists of load cylinder inertia car potentiometer and external load cylinder. The experiments were carried out under several conditions and the results were compared. As a result the sliding mode method has shown good control performance and the robust and stable positioning of the elector-hydraulic servo system can be achieved accurately.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.81-85
• /
• 2003

The Bi-directional Wireless Capsule endoscope con sists of CMOS Image sensor, FPGA, LED, Battery, DC to DC Converter, Transmitter, Receiver and Antennas. The RF transmitter at 1.2GHz range is designed and fabricated with 10 mm(diameter)x1.6 mm(thickness) dimension considering the maximum permission exposure(MPE), system size, power consumption, linearity and modulation method. The fabricated RF receiver at 400MHz range can demodulate the external signals so as to control the behavior of CMOS image sensor. four LEDs and Transmitter.