• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.513-518
• /
• 1998

In Half Precast Concrete Method, such as composite slab and composite wall, Interface between half PC plate and cast-in-place concrete is occurred. And this interface endure lastly in-plane shear which is occurred by external force. Therefore, test was executed to study in-plane shear strength of interface between half PC plate and cast-in-place concrete. In this test, Experimental parameters are finishing condition of the interface, cohesion of concrete, existence and nonexistence of re-bar truss, and angle and direction of lattice of re-bar truss. Comparing and analyzing experimental results, conclusions are obtained as follows. (1) In-plane shear strength of wide interface in composite plate is more affected by the roughness of interface than re-bar truss. And cohesion of concrete contribute to increasing in-plane shear strength. Therefore it seems that the interface should be roughen and kept clean to improve in-plane shear strength. (2) It seems that shear friction equation in ACI code can be sagely available for design of in-plane shear of composite plate.

• 대한기계학회논문집A
• /
• 제24권6호
• /
• pp.1427-1437
• /
• 2000

In the authors＇ preceeding paper, an improved component mode synthesis (CMS) technique in which experimental data as well as finite-element data are available in sub-systems has been proposed. Thi s technique, called an improved experimental free-interface method (IEFIM), has been proved to be more accurate and more efficient than the conventional experimental CMS method based on McNeal's formulation. It is due to the facts that dynamic residual terms as well as static ones are compensated from experimentally obtained FRFs and that FRFs measured on any frequencies can be used for the compensation. In this paper, the technique is applied to the component mode synthesis of a car body structure. As a result, the applicability of the technique to a large structure is demonstrated.

• Geomechanics and Engineering
• /
• 제17권6호
• /
• pp.553-564
• /
• 2019

This paper presents experimental results of rock-concrete bi-material discs under cyclically diametrical compression. It was found that both specimens under cyclical and static loading failed in three typical modes: shear crack, tensile crack and a combined mode of shear and wing crack. The failure modes transited gradually from the shear crack to the tensile one by increasing the interface angle between the interface and the loading direction. The cycle number and peak load increased by increasing the interface angle. The number of cycles and peak load increased with the interface groove depth and groove width, however, decreased with increase in interface groove spacing. The concrete strength can contribute more to the cycle number and peak load for specimens with a higher interface angle. Compared with the discs under static loading, the cyclically loaded discs had a lower peak load but a larger deformation. Finally, the effects of interface angle, interface asperity and concrete strength on the fatigue strength were also discussed.

• 전기학회논문지
• /
• 제56권6호
• /
• pp.1087-1091
• /
• 2007

Exact impedance modeling of the electrode/electrolyte interface is important in bio-signal sensing electrode development. Therefore, the investigation of the equivalent circuit models for the interface has been pursued for a long time by several researchers. Previous circuit models fit the experimental results in limited conditions such as frequency range, type of electrode, or electrolyte. This paper describes a new electrical circuit model and its capability of fitting the experimental results. The proposed model consists of three resistors and two constant phase elements. Electrochemical impedance spectroscopy was used to characterize the interface for Au, Pt, and stainless steel electrode in 0.9% NaCl solution. Both the proposed model and the previous model were applied to fit the measured impedance results for comparison. The proposed model fits the experimental data more accurately than other models especially at the low frequency range, and it enables us to predict the impedance at very low frequency range, including DC, using the proposed model.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 하계종합학술대회 논문집
• /
• pp.749-752
• /
• 1999

A new interface circuit for variable resistive sensors is proposed. The interface circuit compose of only two strain gages, a voltage-to-current converter, and current mirror with two outputs. A new dual slope A/D converter based on linear operational transconductance amplifier for the testing of prototype interface circuit is also described. The theory of operation is presented and experimental results are used to verify the theoretical predictions. The results show close agreement between predicted behaviour and experimental performance.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.951-955
• /
• 2001

The experimental comparison between bonded and unbonded types stem-cement interface was carried out on axisymmetric stem-cement-aluminum model of the femoral component of a total hip replacement. Human femur was modeled in non-tapered and tapered($7.5^{\circ}$) aluminum hollow cylinders to emulate the diaphyseal and metaphyseal segments of the femur. For unbonded type, we tested stems with three different taper angles($5^{\circ},\;7.5^{\circ},\;10^{\circ}$). In every case, the cement-aluminum interface was designed to endure 8MPa shear strength. (a measured value at cement-bone interface) We tested aluminum models under axial loading for both cases. As an experimental result, it was found that unbonded stem sustained more axial load as bonded stem in both cases, diaphyseal and metaphyseal models. The unbonded types failed in cement mantle under axial compressive load, while the bonded ones failed in shear at cement-aluminum interface. These results suggest that a polished stem will sustain much higher axial load than a roughened stem. And a polished stem will make more stable cement-bone interface that may promote better osteosythesis around the stem.

• 콘크리트학회논문집
• /
• 제21권6호
• /
• pp.781-788
• /
• 2009

강-콘크리트 계면의 성질을 대표하는 부착강도, 부착 및 비부착 마찰계수, 부착 및 비부착 마찰계수의 연화영역에서 잔류량의 크기, 모드 I 파괴에너지, 부착 및 비부착 모드 II 파괴에너지, 파괴포락선의 형상계수를 포함한 총 9개 계면상수의 값을 계면거동실험결과와 파괴포락선의 기하학적 형상 및 구성모델을 이용하는 민감도 해석을 통해 결정하였다. 계면의 거동이 계면의 부착상태뿐만 아니라 계면법선방향 응력의 방향과 크기에 따라 매우 민감하게 작용하므로 계면상수 값의 결정에서는 이러한 구속압의 크기와 부착 및 비부착 계면조건을 고려하였다. 강재판 사이에 콘크리트가 타설된 강-콘크리트 계면실험체의 거동해석을 위한 계면유한요소해석을 결정된 계면상수를 적용하여 수행하였으며 실험결과와의 비교를 통해 상수값의 적정성을 검토하였다.

• 한국과학교육학회지
• /
• 제15권2호
• /
• pp.164-172
• /
• 1995

In this study, the researcher tried to find out the effect of using a computer interface in teaching speed concept in the elementary school. The 4th and 5th pupils were sampled for this study. The school is located in a sub-urban agricultural area in Korea. In the study, the subjects were divided into two groups: experimental and comparison group. From the pretest, two groups did not show any difference in the understanding of speed concept. The computer interface and the programs to operate the interface and data analysis were developed by researcher. The interface is a modular type and designed ready to connect to microcomputer. The test items were consisted of (1) comparison of speed, (2) change of motion, (3) acceleration, and (4) deceleration. As the result, the researcher found the following results: 1. In case of speed comparison, no significant difference was found between experimental and comparison group. 2. In case of change of motion, acceleration, and deceleration, the experimental groups showed higher achievement both in 4th grade and 5th grade. However, the 4th graders showed more learning than the 5th graders. In conclusion, this study showed that the use of computer interface seemed to be very effective in teaching and learning speed concept in elementary school.

• 대한인간공학회:학술대회논문집
• /
• 대한인간공학회 1998년도 춘계학술대회논문집
• /
• pp.93-98
• /
• 1998

Recently, consumers are tend to purchase the user-centered designed product using interface enginnering and human factors techniques. Therefore, it is important that the designer's requirements should be analyzed focused on the human machine interface. This paper described the interface usability evaluation technique(suvjective evaluation) for the interface between user and product. This methodology is the integrated interface usbility evaluation method AHP and Conjoint Analysis. AHP(Analytic Hierarchy Process) is a multicriteria decision model to give priority after expressing hierarchically for decision making problem. Conjoint Analysis enduavors to unravel the value, or partworths, that consumers place on the product or service's attributes from experimental subjects' evluation of profiles based on hypothetical products or services. A new usability test methodology proposed by this paper includes techniques jointed both consistency test by AHP and experimental subjective evaluation of profiles by Conjoint Analysis for evaluating the user's emotion and impression.

• Biomolecules & Therapeutics
• /
• 제10권4호
• /
• pp.281-286
• /
• 2002

In this study, we intended to get a preliminary data for establishing rat tracheal surface epithelial(RTSE) cell culture system as an experimental model for physiology and pharmacology of tracheal epithelial cells. Primary culture on the membrane support and application of the air-liquid interface system at the level of cell layer were performed. The cell growth rate and mucin production rate were measured according to the days in culture. The results were as follows: this culture system was found to manifest mucocilliary differentiation of rat tracheal epithelial cells, the cells were confluent and the quantity of produced and released mucin was highest on culture day 9, the mucin was mainly released to the apical side and tbe free $^3{H}$-glucosamine which was not incorporated to process of synthesis of mucin was left on the basolateral side. Taken together, we suggest that air-liquid interface culture system can be used as a substitute for immersion culture system and as an experimental model for in vivo mucus-hypersecretory diseases.