• 반도체디스플레이기술학회지
• /
• 제15권2호
• /
• pp.81-86
• /
• 2016

Moisture vapor transmission rate (MVTR) is an important item for many applications of polymer breathable thin film. To determine the optimum values of the process parameters, it is essential to find their influence on The significance of six important process parameters namely, extruder cylinder temperature, extruder speed, extruder dies temperature, cooling roll temperature, stretching ratio, stretching roll temperature on breathable film strength of polymer extrusion was determined. Moreover, this paper presents the application of Taguchi method and analysis of variance (ANOVA) for maximization of the breathable film MVTR influenced by extrusion parameters. The optimum parameter combination of extrusion process was obtained by using the analysis of signal-to-noise ratio. The conclusion revealed that extruder speed and stretching ratio were the most influential factor on the film strength, respectively. The best results of film MVTR were obtained at higher extruder speed and stretching ratio.

• The Korean Journal of Ceramics
• /
• 제3권1호
• /
• pp.13-17
• /
• 1997

It is identified that the diamond films grown o bias-treated (100) silicon showed different surface morphologies and film textures according to the initial applied dc bias voltage at the same growth condition. The highly oriented diamond film (HODF) was successfully grown on -200 V bias-treated silicon substrate in which the heteroepitaxial relation of $(100)_{dimond}//(100)_{si}\; and\; [110]_{diamond}//[110]_{si}$ was identified. On the contrary, the heteroepitaxial relation was considerably disturbed in the samples bias-voltage was a key factor in growing the highly oriented diamond film on (100) silicon substrate. Considering the experimental results, we proposed a new model about heteroepitaxial diamond growth on silicon, in which 9 diamond unit cell are matched with 4 silicon cells and the bond covalency of both atoms is satisfied via the intermediate layer at the interface as well.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.61-62
• /
• 2014

To evaluate anti-corrosion performance of high-frequency arc metal spray film in accordance with metal type and epoxy sealing coat application status, electrochemical impedance spectroscopy(EIS) method was conducted in this study. As a result, in case of applying Al-Mg alloy metal spray film, it showed the best polarization resistance. In case of applying epoxy sealing coat, it showed increased polarization resistance of arc metal spray film. Through this experiment, it is judged that Al-Mg alloy arc metal spray film with epoxy sealing coat can increase the biggest anti-corrosion performance of high-frequency arc metal spray film on steel.

• 소성∙가공
• /
• 제21권1호
• /
• pp.30-35
• /
• 2012

FIM(Film Insert Molding) is an innovative method of producing decorated parts for a wide range of products. Because it requires fewer steps when compared to conventional production methods, the time and cost of manufacturing high quality components can be reduced considerably. In this paper, the effects of processing conditions on the warpage of film-insert molded plate were investigated by using a design of experiments. The dominant factors affecting warpage were mold temperature and holding pressure. Warpage increased with the temperature difference between stationary mold and fixed one. Even when the mold temperature difference was zero, the plate with a film was bent after ejection such that the film side protruded. As holding pressure increased, warpage decreased significantly. In addition warpage increased with time increment for the film-insert molded plates.

• 한국가시화정보학회지
• /
• 제21권3호
• /
• pp.33-38
• /
• 2023

Spray cooling is a method of cooling high-temperature heating elements by spraying droplets. Recently, spray cooling has been proposed for use in next-generation nuclear reactors. When droplets are sprayed onto the outer wall of a heat exchanger tube, a film boiling occurs on the outer wall. Over time, the outer wall temperature decreases, and a liquid film forms on the outer wall, and the heat exchanger outer wall is subsequently cooled by the liquid film. In this case, the liquid film thickness has a great influence on the heat removal performance. In this study, an experimental study was conducted to measure the liquid film thickness distribution in a droplet spray environment. For this purpose, a method using the electrical conductivity of the liquid was adopted.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.104-111
• /
• 2011

To protect the turbine blade, many cooling techniques has developed. With all other things, film-cooling has been widely used as the important alternative. In the present work, numerical analysis has been performed to investigate and to compare the film-cooling performance of various film-cooling hole schemes such as cylindrical, crescent, louver, and dumbbell holes. To analyze the turbulent flow and the film-cooling mechanism, three-dimensional Reynolds-averaged Navier-Stokes analysis has been performed with shear stress transport turbulence model. The validation of numerical results has been assessed in comparison with experimental data. The characteristics of fluid flow and the film-cooling performance for each shaped hole have been investigated and evaluated in terms of centerline, laterally averaged and spatially averaged film-cooling effectivenesses. The dumbbell shaped hole shows better film-cooling effectiveness than other shaped holes. And the louver and cylindrical shaped hole shows lower one, and concentrated flow on centerline only.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.90-96
• /
• 2003

Numerical analyses have been performed to obtain the absorption heat and mass transfer coefficients and the absorption mass flux from a falling film of LiBr solution. In the present study, the behavior of laminar-wavy falling film in the vertical absorber was studied analytically and experimentally. The change of absorption performance on mean film thickness, wave amplitude, wave celerity was analysed. The heat and mass transfer equations are solved simultaneously to give the temperature and concentration variations at the LiBr solution/refrigeration vapor interface and at the wall. Effects of uniform film, wavy film and film Reynolds number on the heat and mass transfer coefficients have been estimated. The analytical results of the uniform and wavy falling film in the bare tube was higher than experimental result for $Rd_{t}<100$. The absorption performance showed the maximum at the wavy film by the insert device(spring).

• 설비공학논문집
• /
• 제18권11호
• /
• pp.867-873
• /
• 2006

Vertical falling liquid film is extensively used in heat and mass transfer processes of many applications, such as evaporative coolers, cooling towers, and absorption chillers. In such cases, it is required that the falling film spreads widely in the surface forming thin liquid film to enlarge contact surface. An addition of surface active agent to a falling liquid film or hydrophilic surface treatment affects the fluid physical properties of the film. Surfactant addition not only decreases contact angle between the liquid and solid surface but also changes the surface from hydrophobicity to hydrophilicity. In this study, the effects of contact angle on falling film characteristics over a vertical surface have been investigated experimentally. The contact angle is varied either by an addition of surfactant to the liquid or by hydrophilic surface treatment. It is found that the wetted area is increased and film thickness is decreased by the hydrophilic treatment as compared with those of other surfaces. With this hydrophilic treatment, the falling liquid film spreads out widely in the surface. As surfactant concentration is increased, wetted area is also increased and the film thickness is substantially decreased.

• 한국세라믹학회지
• /
• 제29권12호
• /
• pp.990-996
• /
• 1992

Chemical vapor deposition of ATO from SnCl4-SbCl5-H2O gas mixture was investigated with thermodynamic and experimental analyses. Electrical conductivity of the ATO film was much improved under deposition conditions of low input-gas ratio, Psbcl5/Psbcl4. This increase of the conductivity was attributed to donor electrons produced mainly by the pentavalent Sb ions in SnO2 lattice. However high input-gas ratio conditions produced an ATO film consisting of a mixture of SnO2 and very fine Sb2O5 phase. It was found that the deterioration of electrical conductivity and optical transmission of the film was caused by the deposition of fine Sb2O5 phase in the SnO2 matrix.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.2062-2072
• /
• 1991

본 연구에서는 역류의 측정과 원주의 근접 후류의 난류 구조에 미치는 자유흐 름 난류의 영향을 정성적 및 정량적으로 조사하기 위하여, 역류가 존재할 경우나 순간 유입각이 매우 큰 경우에도 난류의 측정이 가능한 split film probe(이하 SFP로 줄여 표기함)를 사용하여 평균 유동장과 난류의 2차 및 3차 모멘트의 변화, 속도 변동 상관 의 변화 및 대규모 와류의 유출 주파수 특성 등을 측정 분석하여, 격자에 의해 형성된 서로 다른 자유흐름 난류특성에 따른 실험 결과들을 비교 검토 해보고자 한다.